Add pin control information for the NAND flash interface. This interface
is multiplexed with the device bus interface to the function is "dev"
not "nand" as one might expect.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
While converting PCIe node on kirkwood by using label, the following
commit eb13cf8345 ("ARM: dts: kirkwood: Fixup pcie DT warnings")
introduced a regression on the OpenRD boards: the PCIe didn't work
anymore. As reported by Aaro Koskinen, the display/framebuffer was
lost. This commit adds the forgotten label.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: eb13cf8345 ("ARM: dts: kirkwood: Fixup pcie DT warnings")
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
By assigning the pin hog to the pinctrl node, we correctly configure the
MPPs. However, they are not available to userspace.
Fix this by assigning the hogs to the gpio node.
After this, the following works as expected:
# echo 28 >/sys/class/gpio/export
# echo low >/sys/class/gpio/gpio28/direction
[gregory.clement@free-electrons.com: fix title]
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The ARM GIC only supports interrupts with either level-high or
rising-edge types for SPIs. The interrupt type for the Palmas PMIC used
for Tegra114 boards is specified as level-low which is invalid for the
GIC. This has gone undetected because until recently, failures to set
the interrupt type when the interrupts are mapped via firmware (such as
device-tree) have not been reported. Since commits 4b357daed6
("genirq: Look-up trigger type if not specified by caller") and
1e2a7d7849 ("irqdomain: Don't set type when mapping an IRQ"), failure
to set the interrupt type will cause the requesting of the interrupt to
fail and exposing incorrectly configured interrupts.
Please note that although the interrupt type was never being set for the
Palmas PMIC, it was still working fine, because the default type setting
for the interrupt, 'level-high', happen to match the correct type for
the interrupt.
Finally, it should be noted that the Palmas interrupt from the PMIC is
actually 'level-low', however, this interrupt signal is inverted by the
Tegra PMC and so the GIC actually sees a 'level-high' interrupt which is
what should be specified in the device-tree interrupt specifier.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix for v4.8-rc1:
1. Select proper eMMC HighSpeed mode on Odroid XU. DTS was mixing
"samsung,exynos5250-dw-mshc" compatible (with HS200 as fastest mode)
with a property "mmc-hs400-1_8v" thus leading to failures during
probe.
2. Update Krzysztof Kozlowski's email address in maintainers.
* tag 'samsung-fixes-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
MAINTAINERS: Switch to kernel.org account for Krzysztof Kozlowski
ARM: dts: exynos: Properly select eMMC HighSpeed mode on Odroid XU
Signed-off-by: Olof Johansson <olof@lixom.net>
The i.MX fixes for 4.8:
- Fix typo in imx6sx-sabreauto board wakeup property
- Fix i.MX6UL suspend-to-standby support by adding the
BM_CLPCR_BYP_MMDC_CH0_LPM_HS handling
- Fix a i.MX6UL regression on suspend support, which is caused by
commit 850bea2335 ("arm: Remove unnecessary of_platform_populate
with default match table")
* tag 'imx-fixes-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6ul: populates platform device at .init_machine
ARM: imx6: add missing BM_CLPCR_BYP_MMDC_CH0_LPM_HS setting for imx6ul
ARM: dts: imx6sx-sabreauto: Fix misspelled property
Signed-off-by: Olof Johansson <olof@lixom.net>
Fixes for omaps for v4.8-rc cycle, mostly a series of four fixes for
am335x RTC zero offset for clkctrl register. Also few other fixes:
- Add missing sysc information for DSI as at least n950 needs it for
the working display
- Fix old elm-id properties that cause nand boot to not work
- Fix overo gpmc nand cs0 range
- FIx overo gpmc nand on boards with ethernet
- Fix logicpd torpedo nand ready pin nand interrupt configuration
* tag 'omap-for-v4.8/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: logicpd-somlv: Fix NAND device nodes
ARM: dts: logicpd-torpedo-som: Provide NAND ready pin
ARM: dts: overo: fix gpmc nand on boards with ethernet
ARM: dts: overo: fix gpmc nand cs0 range
ARM: dts: am335x: Update elm phandle binding
ARM: OMAP4+: CM: Remove redundant checks for clkctrl_offs of zero
ARM: OMAP4+: Have _omap4_wait_target_* check for valid clkctrl_offs
ARM: OMAP2+: AM33XX: Add HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET flag to rtc hwmod
ARM: OMAP4+: hwmod: Add hwmod flag for HWMOD_OMAP4_ZERO_CLKCTRL_OFFSET
ARM: OMAP3: hwmod data: Add sysc information for DSI
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu fixes for 4.8 (part 1)
Fix lan numbering for the Armada 388 clearfog board
* tag 'mvebu-fixes-4.8-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-388-clearfog: number LAN ports properly
Signed-off-by: Olof Johansson <olof@lixom.net>
A23/A33 has a NAND controller which can now be used properly.
Add a device node for it.
The DMA function cannot work because of changed DMA IP block, so it's
temporarily removed in the device node. However, with PIO mode it can still
work.
Tested on an Aoson M751s tablet with Boris Brezillon's "mtd: nand: allow
vendor specific detection/initialization" patchset, which is needed for the
large-block MLC chip to be recognized correctly.
( http://lists.infradead.org/pipermail/linux-mtd/2016-June/068198.html )
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Raspberry Pi Zero is a minified version of model A+. It's
notable there is no PWR LED and the ACT LED is inverted.
Additionally the Pi Zero is capable of the USB peripheral mode.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In case dr_mode isn't passed via DT, the dwc2 defaults to OTG mode.
But all Raspberry Pi boards here are designed only for host mode.
So fix this issue by providing a dtsi file which set the dr_mode
to host.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
According to the DWC2 binding an appropriate clock is required.
This clock isn't handled by bcm2835 clock driver, so add a fixed
clock to the bcm283x DT.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch enables getting a HPD GPIO descriptor quicker.
The exynos-hdmi driver uses "hpd" for HDMI hot plug detection.
static int hdmi_resources_init(struct hdmi_context *hdata)
{
...
hdata->hpd_gpio = devm_gpiod_get(dev, "hpd", GPIOD_IN);
...
}
This calls 'of_find_gpio()' and it generates the GPIO consumer ID by referring
GPIO suffix. So 'hpd-gpios' is preferred on getting a GPIO descriptor.
However, if the device tree uses 'hpd-gpio', then the exynos-hdmi driver
always retries to get a GPIO descriptor because the first GPIO suffix is not
'gpio' but 'gpios'. So you always see the debug message below.
of_get_named_gpiod_flags: can't parse 'hpd-gpios' property of node '/soc/hdmi@14530000[0]'
Use the preferred property, 'hpd-gpios' instead of 'hpd-gpio'.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Qualcomm SPMI GPIO and MPP lines are problematic: the
are fetched from the main MFD driver with platform_get_irq()
which means that at this point they will all be assigned the
flags set up for the interrupts in the device tree.
That is problematic since these are flagged as rising edge
and an this point the interrupt descriptor is assigned a
rising edge, while the only thing the GPIO/MPP drivers really
do is issue irq_get_irqchip_state() on the line to read it
out and to provide a .to_irq() helper for *other* IRQ
consumers.
If another device tree node tries to flag the same IRQ
for use as something else than rising edge, the kernel
irqdomain core will protest like this:
type mismatch, failed to map hwirq-NN for <FOO>!
Which is what happens when the device tree defines two
contradictory flags for the same interrupt line.
To work around this and alleviate the problem, assign 0
as flag for the interrupts taken by the PM GPIO and MPP
drivers. This will lead to the flag being unset, and a
second consumer requesting rising, falling, both or level
interrupts will be respected. This is what the qcom-pm*.dtsi
files already do.
Switched to using the symbolic name IRQ_TYPE_NONE so that
we get this more readable.
This misconfiguration was caused by a copy/pasting the
APQ8064 set-up, the latter has been fixed in a separate
patch.
Tested with one of the SPMI GPIOs: after this I can
successfully request one of these GPIOs as falling edge
from the device tree.
Fixes: 0840ea9e44 ("ARM: dts: add GPIO and MPP to MSM8660 PMIC")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Qualcomm PMIC GPIO and MPP lines are problematic: the
are fetched from the main MFD driver with platform_get_irq()
which means that at this point they will all be assigned the
flags set up for the interrupts in the device tree.
That is problematic since these are flagged as rising edge
and an this point the interrupt descriptor is assigned a
rising edge, while the only thing the GPIO/MPP drivers really
do is issue irq_get_irqchip_state() on the line to read it
out and to provide a .to_irq() helper for *other* IRQ
consumers.
If another device tree node tries to flag the same IRQ
for use as something else than rising edge, the kernel
irqdomain core will protest like this:
type mismatch, failed to map hwirq-NN for <FOO>!
Which is what happens when the device tree defines two
contradictory flags for the same interrupt line.
To work around this and alleviate the problem, assign 0
as flag for the interrupts taken by the PM GPIO and MPP
drivers. This will lead to the flag being unset, and a
second consumer requesting rising, falling, both or level
interrupts will be respected. This is what the qcom-pm*.dtsi
files already do.
Switched to using the symbolic name IRQ_TYPE_NONE so that
we get this more readable.
Cc: stable@vger.kernel.org
Fixes: bce3604696 ("ARM: dts: apq8064: add pm8921 mpp support")
Fixes: 874443fe9e ("ARM: dts: apq8064: Add pm8921 mfd and its gpio node")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
AP148 has a SATA port, but no entity to populate the AHCI
Port Implemented register, so force this in DT.
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Define the Blanche board dependent part of the DU device node.
Add the device nodes for the Analog Devices ADV7511W HDMI transmitter
(connected to DU0) and ADV7123 video DAC (connected to DU1). Add the
necessary subnodes to interconnect DU, HDMI/VDAC devices, and HDMI/VGA
connectors.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Blanche board dependent part of the SDHI0 (connected to the
micro-SD slot) device node along with the necessary voltage regulator.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a dts file for tablets using the generic inet-q972 PCB.
Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.
This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Just like with a13/a23/a33 most a31 tablets are derived from the same
reference design. Add a .dtsi file with all the common bits to avoid
endless copy and pasting of these.
The sun6i-reference-design-tablet.dtsi this commit adds is a copy
of sun6i-a31s-colorfly-e708-q1.dts with a few tablet specific bits
removed / left in sun6i-a31s-colorfly-e708-q1.dts.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The 32.768 kHz clock inside the A80 SoC is fed from an external source,
typically the AC100 RTC module.
Make the osc32k placeholder a fixed-factor clock so board dts files can
specify its source.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Almost all sun8i tablets use a gsl1680 touchscreen controller, so add
a node describing it to reference-design-tablet.dtsi.
Almost all, but not all, so mark it as disabled by default (dts files
will also need to supply a firmware-name and resolution info).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ga10h tablet has a rtl8703as wifi chip, add a dt node describing it.
This enables usage of wifi on this tablet (together with the out of
tree rtl8732bs driver).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This results in quite a nice cleanup for this dts file.
As an added bonus this also enables full otg support. I've tested that
this works as advertised.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A33-OLinuXino is A33 development board designed by Olimex LTD.
It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.
It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CHIP has a status LED connected to one of the AXP GPIOs. Add the
gpio-leds node to be able to use the proper LED framework to control it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the general purpose software switches SW2 and tactile
switches SW24/25 as a virtual keyboard (like it was done with the Lager/
Koelsch boards).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The LCDK embeds a TLV320AIC3106 connected to the SoC McASP for analog
audio. The power supply of the codec comes from the main PMIC
(TPS650250) DCDCs which are always on per HW design and not
controllable by SW, so SW wise the codec driver will rely on the 'dummy'
regulator.
Quality is good with arecord -pipe- aplay on Line In/Line Out.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The "linux,stdout-path" is deprecated.
Add serial options so the console can be properly configured when
bootloader does not pass "console" parameter to the command line. Without
options and lack of "console" in command line, the serial output dies
during boot (just after probing sound, probably because of rate change).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
There are many regulators are missed in previous commit, this
commit complete most of them. It also fix some mistakes in the
regulator properties. The VDD_10(REG10) and VCC_18(REG11) had better
to keep in always-on state, as it is used as the USB PHY supply,
corretly we have no way to assign power supply to a USB PHY.
The VCCA_33(REG8) should be enabled or the GMAC won't work.
It also fix the wrong properties for audio in io-domains, the supply
connected to APIO4_VDD is different to firefly release version.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Because of a bug in hardware design, the sdcard at firefly
rk3288 reload board can't switch the io voltage level to 1.8v.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
