In DMA start window scheduling, TRIG_CTRL.COMMAND_MODE_DMA_TRIGGER_SEL
is programmed to SW + DMA start window trigger. But if DMS switch
comes after command is scheduled, COMMAND_MODE_DMA_TRIGGER_SEL gets
reprogrammed to SW trigger leading to command transfer failure.
Program the COMMAND_MODE_DMA_TRIGGER_SEL only from the CMD DMA Tx path.
Change-Id: I01062497bb70aa5fdcb25be3715c7cbc4c68b681
Signed-off-by: Ritesh Kumar <quic_riteshk@quicinc.com>
Signed-off-by: Rajeev Nandan <quic_rajeevny@quicinc.com>
Signed-off-by: Kirill Shpin <quic_kshpin@quicinc.com>
DSI PHY isolation is unused and considered deprecated. Previous uses
were for power measurements and emulated platform support. Use on
emulated platforms has been supplanted by PHY PLL bypass.
Change-Id: I547681912ff82f0df09a1b98c671eac32c19412a
Signed-off-by: Alex Danila <quic_eadanila@quicinc.com>
This change adds support for bypassing hw access in DSI PHY/PLL
drivers which enables the DSI driver to run on emulation
platforms that might be missing those modules.
Change-Id: I3e83155a79d60f2357606746214d776cefabd651
Signed-off-by: Rajkumar Subbiah <quic_rsubbia@quicinc.com>
Signed-off-by: Shamika Joshi <quic_shamjosh@quicinc.com>
Signed-off-by: Alex Danila <quic_eadanila@quicinc.com>
Added dsi ctrl version 2.8 support for pineapple hardware
Change-Id: If9beb77c53d70d94b498b5b837c26892a4df9089
Signed-off-by: Kirill Shpin <quic_kshpin@quicinc.com>
Add DSI CTL MISR support for ctl 2.2 version. Reuse the same
debugfs nodes to setup/collect misr.
Change-Id: I3d8dfab093659ce53817d9511999c0c03cc33f62
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
* quic/display-kernel.lnx.5.10:
disp: msm: sde: avoid error during fal10_veto override enablement
disp: msm: update copyright description
disp: msm: sde: configure dest_scaler op_mode for two independent displays
disp: msm: dp: updated copyright set for 4nm target
Revert "disp: msm: sde: consider max of actual and default prefill lines"
disp: msm: sde: Reset backlight scale when HWC is stopped
disp: msm: dp: avoid duplicate read of link status
disp: msm: dsi: update vreg_ctrl settings for cape
disp: msm: fail commit if drm_gem_obj was found attached to a sec CB
disp: msm: dp: updated register values for 4nm target
disp: msm: sde: update framedata event handling
disp: msm: dsi: Add new phy comaptible string for cape
disp: msm: sde: software override for fal10 in cwb enable
disp: msm: update cleanup during bind failure in msm_drm_component_init
disp: msm: sde: dump user input_fence info on spec fence timeout
disp: msm: sde: add null pointer check for encoder current master
disp: msm: dsi: enable DMA start window scheduling for broadcast commands
disp: msm: sde: avoid alignment checks for linear formats
disp: msm: reset thread priority work on every new run
disp: msm: sde: send power on event for cont. splash
disp: msm: sde: always set CTL_x_UIDLE_ACTIVE register to "1"
disp: msm: use vzalloc for large allocations
disp: msm: sde: Add support to limit DSC size to 10k
disp: msm: sde: add tx wait during DMS for sim panel
disp: msm: dsi: add check for any queued DSI CMDs before clock force update
disp: msm: sde: correct pp block allocation during dcwb dither programming
disp: msm: sde: avoid setting of max vblank count
disp: msm: sde: add cached lut flag in sde plane
disp: msm: sde: avoid use after free in msm_lastclose
disp: msm: sde: update TEAR_SYNC_WRCOUNT register before vsync counter
disp: msm: dsi: Support uncompressed rgb101010 format
disp: msm: sde: update idle_pc_enabled flag for all encoders
disp: msm: sde: flush esd work before disabling the encoder
disp: msm: sde: allow qsync update along with modeset
disp: msm: dp: avoid dp sw reset on disconnect path
disp: msm: sde: consider max of actual and default prefill lines
disp: msm: ensure vbif debugbus not in use is disabled
disp: msm: sde: update cached encoder mask if required
disp: msm: sde: while timing engine enabling poll for active region
disp: msm: enable cache flag for dumb buffer
disp: msm: sde: disable ot limit for cwb
disp: msm: sde: avoid race condition at vm release
disp: msm: dsi: set qsync min fps list length to zero
disp: msm: sde: reset mixers in crtc when ctl datapath switches
disp: msm: sde: update vm state atomic check for non-primary usecases
disp: msm: sde: reset CTL_UIDLE_ACTIVE register only if uidle is disabled
Change-Id: If480e7f33743eb4788549f853ba05e744ecb38d3
Signed-off-by: Narendra Muppalla <quic_nmuppall@quicinc.com>
This change updates copyright description with correct
license marking as per the guidelines.
Change-Id: Ia74b721e78afcc7f8e88bcbccfcf15430111ec37
Signed-off-by: Yashwanth <quic_yvulapu@quicinc.com>
Cape uses phy version 4.3 but requires programming of
different values for vreg_ctrl_0 and vreg_ctrl_1 to
configure LDO setting. Add new phy compatible string
to distinguish cape from other chipsets and program
the registers accordingly.
Change-Id: I68b266cc6e179d211ee0fd05584a605f39b4d31d
Signed-off-by: Srihitha Tangudu <quic_tangudu@quicinc.com>
Add HW recommended programming sequence for when PHY is allowed to turn
off during idle.
Change-Id: Iaeafa17d9821913b42ae669dbd21f244783f4cdd
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
Change adds the new files for DSI PHY version 5 and 4nm
DSI PLL.
Change-Id: I97712d6ce53a60a6fae1c8331b6ba9a5d17b8d34
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
Add dsi ctrl version 2.7 and dsi phy version 5.2 support for
Kalama hardware.
Change-Id: Ia7b4c8a2e1579458f114e466de8b24855e9251ce
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Removes files and version checks for unsupported DSI PHY versions.
Change-Id: I47223a3860e3bcf48eb3b74e405064d8eb375f16
Signed-off-by: Michael Ru <mru@codeaurora.org>
Removes files and version checks for unsupported DSI Controller
HW versions.
Change-Id: Ic0acd34959ddfcf2db79102857e15f4e06da1d3a
Signed-off-by: Michael Ru <mru@codeaurora.org>
When Broadcast is enabled, DMA_DONE bit gets set for slave
controller on command transfer completion but it is not
getting cleared. Due to this, DMA transfer failures on slave
controller are not getting caught. This patch add supports for
clearing DMA_DONE for slave controller on every successful
transfer. This also prints error if transfer fails on slave
controller.
Change-Id: I61ce7b2d8be323adc70d888b5a2416afd9ae9fac
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Change adds support for transferring commands to each sublink.
Change-Id: Iefc0dca7343325cdfe0cf48d41d50e6e2a13bc05
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Change adds the new compatible version strings for DSI PHY and DSI CTRL
for waipio.
Change-Id: I1073034e608cace9d41cc04a9854f15f56828dfe
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Change avoids clock framework APIs to configure the DSI PHY
PLL. It follows HW recommendation to set the byte and pclk
dividers.
Change-Id: I8c110f3997e4ec4c2eaa28778b70091855725ab8
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Currently, mdp_intf_line_count and mdp_intf_tear_line_count register
addresses are defined in dsi_ctrl_hw for debug feature. But mdp_intf
base address is target specific and independent of dsi controller
version. This change adds support for parsing the mdp intf base
address from dt, thereby remapping using base + offset addressing.
Change-Id: Ibb72dfe84a786a5c8b95f6a400e8333f6b46814a
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
During ESD check failure, DSI video engine can get stuck
sending data from display engine. In use cases where GDSC
toggle does not happen like DP MST connected or secure video
playback, display does not recover back after ESD failure.
This change adds support to perform soft reset when DSI
video engine gets stuck.
Change-Id: I9cb31e6c71c4da171f9fe22fc3bee9175711831d
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
This change allows dynamic refresh trigger to sw trigger
and mdp intf flush. With this we can make sure that DSI
timing/clock update and mdp intf timings are updated in
one vsync.
Change-Id: Ic807f498e2e47be6dd0f1e11ff1fc0896a8ec758
Signed-off-by: Vara Reddy <varar@codeaurora.org>
The change adds register mapping of MDP_INTF_[1/2]_TEAR_INT_COUNT_VAL
register to DSI controller. This allows for the controller to read the
line count and frame count of the read pointer during trigger and
successful transfer of DMA command.
To enable the debug feature:
echo 1 > /d/<panel_name>/dsi-ctrl-0/enable_cmd_dma_stats.
To disable the debug feature
echo 0 > /d/<panel_name>/dsi-ctrl-0/enable_cmd_dma_stats.
To read line count value:
cat /d/<panel_name>/dsi-ctrl-0/cmd_dma_stats.
Change-Id: I5cdeb54ca941af05b226a9d7ab332b899ecc5797
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
The change allows for configuring a command DMA window during which
the command is triggered. The DMA window must not intersect with the
MDP tear check window. Once the command transfer is successful, the
trigger control needs to reset to the default DMA trigger specified
by the panel.
Change-Id: I5485ca1f8e141ed92dc8c77c2daf579634271022
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Avoid sharing and have dedicated dsi HW ctrl ops across versions
even if they are identical. It helps to stub out a specific
version of ops if needed.
Change-Id: Ic14c206b526ebe03dd5f47f62701820e7e542670
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
From Lahaina onwards, for compressed DSI output, widebus should be enabled.
In widebus mode, 6 bytes of data are transmitted per pclk.
For uncompressed output, widebus must be disabled to transmit 3 bytes
of uncompressed data per pclk.
Change-Id: I7fc0bdb2e1678152d57b4cbb8295063a2ba8ae73
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Move DSI debugbus dumping logic from DSI driver to sde_dbg
in order to utilize the framework in place for debugbuses.
This allows for more control over the dumping logic, such
as where the dump data is stored(memory/console), via nodes
populated in debugfs.
Change-Id: Iff507fdaa02d26af26743e81f6048aec57c09a76
Signed-off-by: Steve Cohen <cohens@codeaurora.org>
Add changes to support dynamic switching of dsi clock feature for
phy ver 2.0. This helps to avoid RF interference with DSI clock.
Change-Id: I69958d9224665296cc0f272e39dcdfcefbe293d4
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Signed-off-by: Lipsa Rout <lrout@codeaurora.org>
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
DSI PLL is tightly coupled with DSI PHY. This change removes
separate DSI pll driver and makes DSI pll as a subnode to DSI
PHY which is an accurate way of representation. In addition, this
change adds support for 5nm DSI ctrl and PHY revisions and adds
DSI pll support for 5nm. Remove support for older DSI pll revisions
such as 7nm, 10nm, 14nm, 20nm, 28nm.
Change-Id: Ic8b886a9fe24b906e4ec5130720600efa1e59b68
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
DSI PHY timings must be committed every time the values
are updated after a dynamic mode switch.
Change-Id: Id605c76dfe75ec41ceb89000f24baccda189e82f
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Adding debug, info and error prefix for log messages
in dsi files. To enable debug logs
run "echo 0x1 > /sys/module/drm/parameters/debug"
Change-Id: I438ac16954bd1d39450f8adeb7fb17f9ea6f8140
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change is a snapshot of dsi files taken of 4.14
as of commit 764f7c2 (Merge remote-tracking branch
'quic/dev/msm-4.14-display' into msm-4.14)
Change-Id: I8361a844c35a4450f7800964a8da2741676fd6c7
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Continuous splash enabled displays are identified by reading
the MDP ctl registers. DSI cont-splash init settings are
called based on this. Additionally, DSI reads the DSI-CTL
scratch register set by bootloader to detect cont-splash.
This change removes the redundant mechanism in DSI to
detect cont-splash.
Change-Id: Ic58be1e62eda239fcea5e82d9d356905dc552a73
Signed-off-by: Veera Sundaram Sankaran <veeras@codeaurora.org>
This change adds support for dynamic switching of dsi clocks
to avoid RF interference issues. DSI PHY V4 support is added.
Change-Id: I5bdbd6d2916692087c0192d23c8e7598238f161f
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Yujun Zhang <yujunzhang@codeaurora.org>
This change adds support for dynamic switching of dsi clocks
to avoid RF interference issues. Also with dynamic dsi clock
switch feature coming into picture, now populate the supported
refresh rate as list instead of providing a range. Modify the
logic to enumerate all the modes in dsi driver, taking dynamic
bit clocks, resolutions and refresh rates into account.
Change-Id: I5b6e62bc935cf2234bdd96fcb3c7537b4e735fff
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Signed-off-by: Yujun Zhang <yujunzhang@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
