Activate PWM pin muxing for Apalis PWM3. Note that the same PWM3 is
already active on pu6 being Apalis BKL1_PWM as well. Therefore exporting
that one for raw sysfs access will fail and one has to revert to using
the PWM backlight.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Set "critical" trip temperatures for cpu, gpu, mem and pllx thermal
zones. These trips can trigger shut down or reset.
Similar to commit 40823f8e26 ("arm: tegra: set critical trips for
Tegra124").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As described in
Documentation/devicetree/bindings/input/touchscreen/stmpe.txt there is
no 'reg' property under stmpe_touchscreen, so remove it to fix the
following build warning with W=1:
arch/arm/boot/dts/tegra30-apalis-eval.dtb:
Warning (unit_address_vs_reg): Node
/i2c@7000d000/stmpe811@41/stmpe_touchscreen has a reg or ranges
property, but no unit name
Similar to commit 89277e8e26 ("ARM: dts: imx6qdl-apalis: Remove
unneeded reg property").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All Toradex Carrier Boards use a st,m41t0 compatible RTC. Compared to a
st,m41t00 this RTC has also an oscillator fail bit which allows to
detect when the RTC lost track of time.
Similar to commit c53bec16b1 ("ARM: dts: colibri/apalis: use correct
compatible for RTC") covering our NXP i.MX and Vybrid based modules.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a faster speed of 400 kbit/s for regular I2C busses.
Use a slower speed of 10 kbit/s for DDC/EDID to improve reliability.
Use a slower speed of 100 kbit/s for power I2C to be within specs of
the LM95245 temperature sensor.
While at it further annotate I2C pin usage.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This switches a few interrupt definitions that were using either
GPIO_ACTIVE_HIGH or GPIO_ACTIVE_LOW as IRQ type, which is invalid.
This is mostly a cosmetic change, that doesn't affect any driver.
Analogous to Paul's commit 38333641b6 ("ARM: tegra: nyan: Use proper
IRQ type definitions").
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since commit f8f8f1d044 ("clk: Don't touch hardware when reparenting
during registration") ULPI has been broken on Tegra20 leading to the
following error message during boot:
[ 1.974698] ulpi_phy_power_on: ulpi write failed
[ 1.979384] tegra-ehci c5004000.usb: Failed to power on the phy
[ 1.985434] tegra-ehci: probe of c5004000.usb failed with error -110
Debugging through the changes and finally also consulting the TRM
revealed that rather than the CDEV2 clock off OSC requiring such pin
muxing actually the PLL_P_OUT4 clock is in use. It looks like so far it
just worked by chance of that one having been enabled which Stephen's
commit now changed when reparenting sclk away from pll_p_out4 leaving
that one disabled. Fix this by properly assigning the PLL_P_OUT4 clock
as the ULPI PHY clock.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the missing unit address for the VDE IRAM area node in accordance
with the mmio-sram device tree binding.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device tree node for the Video Decoder Engine found on Tegra30 SoC's.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
IRAM is a static RAM that consists of four contiguous 64 KiB blocks,
it is currently used to store CPU resume code, utilized by the video
decoder engine and could be used as a general-purpose fast memory.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All the vf610m4 based boards include the real memory size in their
dts files, so remove the the zero length reg property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as
deprecated") the inclusion of skeleton.dtsi is deprecated, so
remove it as this file will eventually go away someday.
Move its content to the SoC dtsi file, so that the resultant dtb
is the same.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All the vf500 based boards include the real memory size in their
dts files, so remove the zero length reg property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Include memory node unit name in order to fix the following W=1
warnings:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as
deprecated") the inclusion of skeleton.dtsi is deprecated, so
remove it as this file will eventually go away someday.
Move its content to the SoC dtsi file, so that the resultant dtb
is the same.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtc now warns about missing #sound-dai-cells:
arch/arm/boot/dts/imx6ul-geam.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/imx6ul-isiot-emmc.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
arch/arm/boot/dts/imx6ul-isiot-nand.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /soc/aips-bus@2100000/i2c@21a0000/codec@a or bad phandle (referred from sound-dai[0])
Lots of i.MX boards use the SGTL5000 codec, but not all get the warning
because only some reference the codec with "sound-dai" property. However,
the codec should always provide #sound-dai-cells regardless, so fix all
the occurrences.
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The two usb-otg regulators for imx7d-sdb are both called
"regulator-usb-otg1-vbus" and they effectively override each other.
This is most likely a copy-paste error.
Fixes: b877039aa1 ("ARM: dts: imx7d-sdb: Adjust the regulator nodes")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This add a DTS for the Digilent Zybo Z7 board.
This board is the successor board of Zybo, these are almost the same except
for ps-clk-frequency specifications.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu@cybertrust.co.jp>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, ethernet, i2c, qspi, spi and uart.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, 2x i2c, nor flash, spi and uart.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, i2c, nand uart, spi and usb.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains ethernet port, can, i2c, sd, qspi, spi, uart and usb.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The board contains 7z010 with 512MB memory, ethernet, qspi, uart, usbs
and sd. But board is not supporting booting from sd card.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This patch is fixing issue reported by dtc:
arch/arm/boot/dts/zynq-microzed.dtb: Warning (unit_address_vs_reg): Node
/memory has a reg or ranges property, but no unit name
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Prevents the error:
aspeed-smc 1e630000.spi: Error applying setting, reverse things back
The pinmux driver is only capable of modifying selected strapping bits
that make sense to change at runtime. The SPI strapping is not
currently defined modifiable, so "request" the mux as per how the board
is physically strapped.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The Palmetto BMC has a UART connected to a RS-232 transceiver designed
to be used as a serial console for the host processor. It appears as a
D-sub connector on the back of the chassis.
Signed-off-by: Joel Stanley <joel@jms.id.au>
The NanoPi-M1-Plus have a 8GB eMMC, add a node for it.
This eMMC is always powered with 3.3V.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: Fixed "mmc2_8bits_pins" label typo; added subject prefixes]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add the I2C clocks so the I2C busses can be used. The clock input is not
device specific (the AO I2C bus uses clk81 as input, while the two I2C
busses in CBUS have a separate "CLKID_I2C" gate, provided by the clock
controller.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Pull "Samsung DTS ARM changes for v4.17" from Krzysztof Kozłowski:
1. Add WiFi to Artik 5 board.
2. Remove unused samsung_k3pe0e000b memory DTSI.
3. Add few remaining SPDX license identifiers.
4. Refactor Exynos4 by using labels for overriding/extending nodes and
moving respective nodes under the 'soc' node.
5. Add three new Exynos4412-based boards: GT-I9300 (Samsung Galaxy S3),
GT-I9305 (Samsung Galaxy S3 LTE) and GT-N7100/N7105 (Samsung Note 2).
They are based heavily on existing Trats2 board.
6. Fix PMIC interrupts on Trats board.
7. Fix IOMMU for GScaler devices on Exynos5250.
8. Minor fixes in unit addresses pointed by DTC.
9. Minor cleanups from unused properties and duplicated code.
* tag 'samsung-dt-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (29 commits)
ARM: dts: exynos: Fix IOMMU support for GScaler devices on Exynos5250
ARM: dts: exynos: Remove unused bypass-smu property from Xyref5260
ARM: dts: exynos: Add missing interrupts property to PMIC on Trats board
ARM: dts: exynos: Fix unit addresses of PDMA nodes in Exynos5410
ARM: dts: exynos: Fix address of PPMU ACP on Exynos4210
ARM: dts: exynos: Cleanup power domain nodes in exynos3250.dtsi
ARM: dts: exynos: Add touchscreen node to Exynos4412 N710x
ARM: dts: exynos: Add Samsung's Exynos4412-based Midas boards
ARM: dts: exynos: Split Trats2 DTS in preparation for Midas boards
ARM: dts: exynos: Remove "cooling-{min|max}-level" for CPU nodes
dt-bindings: samsung: Document bindings for Midas family boards
ARM: dts: exynos: Add soc node to exynos4412
ARM: dts: exynos: Add soc node to exynos4210
ARM: dts: exynos: Add soc node to exynos4
ARM: dts: exynos: Add soc node to exynos5440
ARM: dts: exynos: Use pmu label in exynos4412
ARM: dts: exynos: Remove duplicated inclusion of syscon restart nodes on Exynos5410
ARM: dts: exynos: Use label instead of full path in exynos4412-itop-elite
ARM: dts: exynos: Use labels instead of full paths in exynos4412-trats2
ARM: dts: exynos: Use label instead of full path in exynos4412-odroid-common
...
As of commit 7f60830ab1 ("serial: sirf: Use generic
uart-has-rtscts DT property property"), the SiRF UART driver recognizes
the generic "uart-has-rtscts" DT property, deprecating the
vendor-specific "sirf,uart-has-rtscts" DT property. Hence replace the
latter by the former in all DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "STM32 DT updates for v4.17, round 1" from Alexandre Torgue:
Highlights:
-----------
-Add support of STM32MP157 MPU and stm32mp157c eval board
-Add SD supports on F4 and F7 boards
-Add leds support on stm32f469 and stm32f769 disco boards
-Add push button support on stm32f469 and stm32f769 disco boards
-Add EXTI, SPI, RTC, USB HS/FS support on STM32H743 MCU
-Add RTC and USB OTG HS on stm32f769-disco
-Use dedicated files for F7 pinctrl
* tag 'stm32-dt-for-v4.17-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (34 commits)
ARM: dts: stm32: Fix sdio2 rcc hard coded value
dt-bindings: mfd: Add STM32F7 SDMMC2 rcc entry
ARM: dts: stm32: Enable sdio1 for stm32f769-disco
ARM: dts: stm32: Enable sdio1 for stm32f746-eval
ARM: dts: stm32: Enable sdio1 for stm32f746-disco
ARM: dts: stm32: Add sdio pins definition for stm32f7
ARM: dts: stm32: add SPI support on STM32H743 SoC
ARM: dts: stm32: enable RTC on stm32h743i-eval
ARM: dts: stm32: add RTC support on STM32H743
ARM: dts: stm32: enable USB OTG HS on stm32h743i-eval
ARM: dts: stm32: add USB OTG HS and FS support for STM32H743 SoC
ARM: dts: stm32: enable RTC on stm32f769-disco
ARM: dts: stm32: enable USB HS on stm32f769-disco
ARM: dts: stm32: select otg mode for usbotg_hs on stm32746g_eval
ARM: dts: stm32: add gadget fifo sizes to usbotg_hs on stm32f746
ARM: dts: stm32: Add push button to stm32f769 Discovery board
ARM: dts: stm32: Add push button to stm32f469 Discovery board
ARM: dts: stm32: Add leds support to stm32f769 Discovery board
ARM: dts: stm32: Add leds support to stm32f469 Discovery board
ARM: dts: stm32: Fix HSE clock frequency for stm32h743i-disco board
...
Pull "Device tree changes for dra7 sdhci for v4.17" from Tony Lindgren:
This series from Sekhar Nori and Kishon Vijay Abraham I adds
sdhci related nodes for dra7. To support higher transfer speeds,
the iodelay pinmux controller needs to be also configured.
Note that as these changes need SDHCI_OMAP to be enabled to avoid
breaking booting for various systems, these changes are based on
two defconfig changes to enable SDHCI_OMAP in the defconfig files.
* tag 'omap-for-v4.17/dt-sdhci-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am57xx-idk: Select pull down for mmc1_clk line in default mode
ARM: dts: dra71-evm: Select pull down for mmc1_clk line in default mode
ARM: dts: dra71-evm: Correct evm_sd regulator max voltage
ARM: dts: dra76-evm: Add "vqmmc-supply" property for mmc2
ARM: dts: am57xx-idk: Add "vqmmc-supply" property for mmc2
ARM: dts: dra7-evm: Add "vqmmc-supply" property for mmc2
ARM: dts: dra7-evm: Remove mmc specific pinmux
ARM: dts: am57xx-beagle-x15: Add "vqmmc-supply" property for mmc2
ARM: dts: dra76-evm: Add pinctrl data for higher speed MMC/SD modes
ARM: dts: dra76-evm: Shift to using common IOdelay data
ARM: dts: dra76x: Create a common file with MMC/SD IOdelay data
ARM: omap2plus_defconfig: Enable CONFIG_MMC_SDHCI_OMAP
ARM: multi_v7_defconfig: Enable CONFIG_MMC_SDHCI_OMAP
Pull "ARM: Keystone DTS for 4.17" from Santosh Shilimkar:
- Andrew's various DTS warning fixes
- clock address separator fix
- EDAC support for EMIF
- serial dts node unit address format fix
* tag 'keystone_dts_for_4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2g: Fix unit-address formatting for serial nodes
dt-bindings: memory: ti-emif: add edac support under emif
ARM: dts: keystone-k2e-clocks: Fix missing unit address separator
ARM: dts: keystone-k2g: Move usb-phy nodes out of soc0
ARM: dts: keystone-k2g: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone-k2g: Move keystone_irq to under device-state-control
ARM: dts: keystone-k2hk: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone-k2l: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone-k2e: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone: Move reset-controller to under device-state-control
ARM: dts: keystone: Move keystone_irq to under device-state-control
Pull "Device tree changes for omap variants for v4.17" from Tony Lindgren:
This series of changes updates the device tree files for omaps:
- Nokia N9 support for magnetometer
- Update at24 to use atmel as manufacturer for am335x-boneblue
- Add support for am33xx based PDU001 board
- Update Droid 4 touchscreen for reset-gpios and add audio
codec and soundcard
- Remove unused dra7 cooling level nodes
- A series of changes to configure am335x and am437x for PM
- Add pinmuxing for i2c2 and 3 for LogicPD boards
- Add EMIF interrupt infor for am437x and am335x
- Add missing omap3 sound-dai-cells
* tag 'omap-for-v4.17/dt-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: omap4-droid4: add soundcard
ARM: dts: motorola-cpcap-mapphone: add audio-codec
ARM: dts: omap3: Add missing #sound-dai-cells
ARM: dts: am43xx: add emif interrupt info
ARM: dts: am33xx: add emif interrupt info
ARM: dts: Add pinmuxing for i2c2 and i2c3 for LogicPD SOM-LV
ARM: dts: Add pinmuxing for i2c2 and i2c3 for LogicPD torpedo
ARM: dts: am4372: Mark omap_l3_noc with ti,no-idle
ARM: dts: am4372: Mark emif with ti,no-idle
ARM: dts: am33xx: Mark emif with ti,no-idle
ARM: dts: am4372: Add soc node
ARM: dts: am33xx: Add pm-sram phandle to soc node
ARM: dts: am4372: Update emif node
ARM: dts: am33xx: Update emif node
ARM: dts: am4372: Reserve pm code and data regions in ocmcram sram node
ARM: dts: am33xx: Reserve pm code and data regions in ocmcram sram node
ARM: dts: omap: Remove "cooling-{min|max}-level" for CPU nodes
ARM: dts: omap4-droid4: update touchscreen
ARM: dts: am33xx: add PDU001 board
ARM: dts: use 'atmel' as at24 manufacturer in am335x-boneblue
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
'linux,stdout-path' has been deprecated for some time in favor of
'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
Search and replace all the of occurrences with 'stdout-path'.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "DaVinci DT support enhancements for v4.17" from Sekhar Nori:
* Lego EV3 gains firmware recovery mode support
* Miscellaneous non-critical clean-up
* tag 'davinci-for-v4.17/dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-evm: add chosen and SPI alias
ARM: dts: da850-lego-ev3: use a correct fallback for at24 compatible
ARM: dts: da850-lego-ev3: Add node for reboot modes
Add node for the hardware crypto acceleration used in the artpec6 SoC.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PCIe controller in the artpec6 SoC supports both root complex and
endpoint mode, however, the controller can only be used in one of the
modes.
Both pci nodes are disabled by default. A DTS file can enable one of
them, depending on what mode it wants to run.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add nodes for the nbpfaxi DMA controllers used in the artpec6 SoC,
and start using them for the exising UARTs.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add node for the pin controller used in the artpec6 SoC,
and start using it for the exising UARTs.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The snps,dwc-qos-ethernet binding is still supported as a glue layer
in the stmmac driver.
However, since the snps,dwc-qos-ethernet binding is now deprecated,
migrate to stmmac's native binding.
At the same time, enable features supported by the stmmac driver,
such as PTP, LPI, and an additional tx queue.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
