The UniPhier AIO audio system needs I2S data in/out lines
and clock signal pins to connect external codec chip.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since 'num-slots' had already deprecated, remove the property in
device-tree file.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since 'num-slots' had already deprecated, remove the property in
device-tree file.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The compatible string was mistakenly pulled from the downstream tree and the
startup delay property is needed to prevent io errors on initial page select.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The #sound-dai-cells property may be required to reference the CPU DAI
properly. This change is required for Snow HDMI audio.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As serial interface is already specified into stdout-path property,
"console=ttyASN,115200" from bootargs can be removed.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update serial aliases from "ttyASN" to more common "serialN".
Since dtc v1.4.6-9-gaadd0b65c987, aliases property name must
be lowercase only. This allows to fix following dtc warnings:
arch/arm/boot/dts/stih418-b2199.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
arch/arm/boot/dts/stih407-b2120.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
arch/arm/boot/dts/stih410-b2260.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
arch/arm/boot/dts/stih410-b2120.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VCHIQ firmware communication channel operates in parallel with our
other mailbox-based channel. This is the communication channel that
exposes the firmware's media decode/encode and ISP interfaces.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com> (v2)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we removed the inclusion of skeleton.dtsi from the device trees, we
broke booting for systems with bootloaders that aren't device tre aware.
This can be seen, for example, when appending the device tree blob to
the kernel image.
The reason booting broke was that the kernel lacked the device_type
label in the memory node. Add in a default memory node wth the
device_type. It can contain the memory address as the location is fixed
for each SoC generation, but the size needs to be added by the
bootloader or the board specific dts.
Fixes: 73102d6fdc ("ARM: dts: aspeed: Remove skeleton.dtsi")
Cc: <stable@vger.kernel.org>
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Qualcomm Centriq 2400 REP (Reference Evaluation Platform) is
an aarch64 Armv8 server platform with an ast2520 BMC.
Signed-off-by: Ken Chen <chen.kenyy@inventec.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
GPIOS7 shall be pulled low for CPLD to continue the power up sequence.
With this hogged as pull-low, the CPLD workaround can be removed in
OpenBMC.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Romulus uses ASPEED's fan tach instead of max31785:
* Pass1's max31785 is always reset by CPLD
* Pass2's max31785 is not connected
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Pull "Broadcom devicetree changes for 4.17" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs devicetree changes
for 4.17, please pull the following:
- Henry fixes the pin functions for the JTAG pins, nothing uses this for
now, but it could be backported eventually if deemed appropriate
- Stefan fixes the register ranges for the bcm2835-i2s nodes in the
binding document definition, he then fixes the probing of the
bcm2835-i2s driver by providing an appropriate register range and a
missing clock. Stefan also makes sure that the appropriate pull
settings are applied to the pins used on the Raspberry Pi Zero
Wireless, he then adds the necessary UART node to connected to the
BCM43438 Bluetooth adapter on the Pi Zero W. He finally enables USB
OTG mode on the Pi Zero W since he became usable again
- Baruch adds the necessary Device Tree nodes to support the Raspberry
Pi GPIO expander which is controlled via the VC4 firmware
- Hiroshi adds the missing LEDs on the Buffalo WZR-900DHP router
- Eric adds the DPI hardware block into the BCM283x Device Tree include
file for future use when an actual panel is available
- Florian updates the Northstar Plus platforms to use port 8 of the
internal switch as the CPU/management port since necessary code was
added in the b53 switch driver to support that
* tag 'arm-soc/for-4.17/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: NSP: Switch to port 8 for CPU port
ARM: bcm2835: Add the DPI hardware to the device tree.
ARM: dts: BCM5301X: add missing LEDs for Buffalo WZR-900DHP
ARM: dts: bcm2835-rpi-zero-w: Enable OTG mode
ARM: dts: bcm2835-rpi-zero-w: Add bcm43438 serial slave
ARM: dts: bcm283x: Apply pull settings to Zero W relevant groups
ARM: dts: bcm2837-rpi-3-b: add GPIO expander
ARM: dts: bcm2835: make the firmware node into a bus
ARM: dts: bcm283x: Fix probing of bcm2835-i2s
dt-bindings: bcm283x: Fix register ranges of bcm2835-i2s
ARM: dts: bcm283x: Fix pin function of JTAG pins
This pull request brings in one last patch to add the BCM2835 DPI
controller to the device tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Now that we have added support for pre-pended Broadcom tags with commit
1160603960 ("net: dsa: b53: Support prepended Broadcom tags") we can
switch all the Northstar Plus reference boards to use port 8 for the CPU
port. This allows us to prepare room for supporting the Flow Accelerator
2 NAPT offload, and frees up port 5 to be made fully configurable for
the modes that it supports: internal, SGMII, RGMII etc.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's currently marked disabled, as it's not useful without a panel
associated with it and the GPIO pins routed to ALT2.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
"debounce-inteval" was never supported.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Pull "Rockchip dts32 fixes for 4.16" from Heiko Stübner:
Fix for a new dtc warning.
* tag 'v4.16-rockchip-dts32fixes-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add missing #sound-dai-cells on rk3288
Pull "i.MX fixes for 4.16, 2nd round" from Shawn Guo:
- Fix a copy-paste error in imx7d-sdb device tree, which results in two
usb-otg regulators are both named "regulator-usb-otg1-vbus" and
override each other.
* tag 'imx-fixes-4.16-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d-sdb: Fix regulator-usb-otg2-vbus node name
Pull "This is the pxa changes for v4.17 cycle" from Robert Jarzmik:
- minor changes for property API
- clock API fix for ULPI driver warning
It exceptionally contains a merge from the mtd tree from Boris
to prevent any merge conflicts in the PXA tree.
* tag 'pxa-for-4.17' of https://github.com/rjarzmik/linux:
ARM: pxa/raumfeld: use PROPERTY_ENTRY_U32() directly
ARM: pxa: ulpi: fix ulpi timeout and slowpath warn
ARM: pxa: cm-x300: remove inline directive
ARM: pxa: fix static checker warning in pxa3xx-ulpi
MAINTAINERS: remove entry for deleted pxa3xx_nand driver
arm: dts: pxa: use reworked NAND controller driver
dt-bindings: mtd: remove pxa3xx NAND controller documentation
mtd: nand: remove useless fields from pxa3xx NAND platform data
mtd: nand: remove deprecated pxa3xx_nand driver
mtd: nand: use Marvell reworked NAND controller driver with all platforms
Add emif node for keystone2 devices, which is used for ECC support.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
[t-kristo@ti.com: made emif enabled by default for all keystone2 devices]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a watchdog node for keystone-k2g, with the corresponding clock and
power domain handles.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "AT91 DT for 4.17" from Alexandre Belloni:
Not much this cycle, mainly changes on the Axentia boards from Peter and
a cleanup from Bartosz:
- use 'atmel' as at24 manufacturer
- device addition and fixes for axentia boards
- fix sama5d4 pinctrl compatible
* tag 'at91-ab-4.17-dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: use 'atmel' as at24 manufacturer for at91sam9263ek
ARM: dts: at91: use 'atmel' as at24 manufacturer for at91-sama5d2_ptc_ek
ARM: dts: at91: use 'atmel' as at24 manufacturer for at91sam9g20ek
ARM: dts: at91: use 'atmel' as at24 manufacturer for at91sam9260ek
ARM: dts: at91: use 'atmel' as at24 manufacturer for sama5d34ek
ARM: dts: at91: sama5d4: fix pinctrl compatible string
ARM: dts: at91: tse850: make the sound dai cell count explicit
ARM: dts: at91: nattis: add lvds-encoder
ARM: dts: at91: nattis: use up-to-date mtd partitions
ARM: dts: at91: tse850: use the correct compatible for the eeprom
ARM: dts: at91: nattis: use the correct compatible for the eeprom
ARM: dts: at91: sam9rl: Properly assign copyright
Pull "mvebu dt for 4.17 (part 1)" from Gregory CLEMENT:
Most of them are small fixes or cleanup.
Only the change on the clearfog will have a noticeable effect allowing
to use the i2c at an higher frequency.
* tag 'mvebu-dt-4.17-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada388-clearfog: increase speed of i2c0 to 400kHz
arm: dts: kirkwood: fix error in #sound-dai-cells size
ARM: dts: kirkwood: Fix "debounce-interval" property misspelling
ARM: dts: armada: netgear-rn*: fix rtc node name
This adds information, that the battery is charged by the charger.
The Linux kernel uses this information to refresh battery information
when the power-supply changes.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Fix that USB initialization fails as below runtime log is present during
booting on bananapi-r2 board by adding missing regulators the USB device
requires. Current regulators USB device uses are being updated with the
correct ones to reflect real configurations which are all from fixed
regulators rather than MT6323 one's output.
xhci-mtk 1a1c0000.usb: 1a1c0000.usb supply vbus not found, using dummy regulator
xhci-mtk 1a240000.usb: 1a240000.usb supply vbus not found, using dummy regulator
Cc: stable@vger.kernel.org
Fixes: f4ff257cd1 ("arm: dts: mt7623: add support for Bananapi R2 (BPI-R2) board")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
[mb: update kernel log in commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The A23/A33 reference tablet design has a DC barrel tied to the ACIN
of the PMIC. And being a tablet, it has a Li-Po battery.
Enable both power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A33-OLinuXino routes the SoC's headphone output to a headphone jack,
and the microphone input to a microphone jack. Power to the microphone
is provided by MBIAS.
This patch enables the various parts of the codec, and adds widgets and
routes for simple-card.
HBIAS is connected to the microphone jack as well, but in a manner that
is confusing and likely does not provide power. This part is left out
of this patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A33-OLinuXino has a DC jack wired to the onboard PMIC's ACIN pins.
There is also a battery connector, wired to the PMIC's battery charger.
Enable the power supplies for both these components.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
None of the common regulators defined in sunxi-common-regulators.dtsi
are used for the A33-OLinuXino.
Drop the include.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Normal GPIO usage does not need an additional pinmix setting. Exclusive
usage of the pin will be guaranteed by the driver.
Drop the extra pinmux settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
According to the i.MX25 reference manuals, each SSI has four FIFOs. All
of those FIFOs can store up to 15 entries.
The fsl_ssi driver's internal default for the FIFO depth in 8. Set our
non-default FIFO depth explicitly in the Device Tree.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds new cpu, codec subnodes according to the updated
"google,snow-audio-max98091" DT bindings and the I2S clock tree
configuration so sound on the HDMI interface can be also supported.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds new cpu, codec subnodes according to the updated
"google,snow-audio-max98090" DT bindings and the I2S clock tree
configuration so sound on the HDMI interface can also be supported.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds new cpu, codec subnodes according to the updated
"google,snow-audio-max98095" DT bindings and the I2S clock tree
configuration so sound on the HDMI interface can also be supported.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds missing clocks, clock-names properties so the CODEC can
properly handle its master clock. Without this change sound on exynos5250-snow
doesn't work.
Missing #sound-dai-cells property is also added so it is possible to specify
the DAI links properly for HDMI audio support.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Currently the audio subsystem clocks are not configured properly on Snow
and sound is not working. The MAX98095 CODEC is not getting its master clock
on the MCLK pin connected to the SOC's CLKOUT GPIO. This patch adds CLKOUT
and other clocks configuration so HDMI audio can also be supported.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This property is required for specifying link between the HDMI IP block
and the SoC's audio subsystem.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Using the enable-method property for SMP support would allow future PSCI
implementations to override any in-OS support. This is better than just
matching against the machine compatible, and then having to determine
whether other methods are available or not.
This adds enable-method properties to all CPU nodes.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Buffalo WZR-900DHP has 8 LEDs, but there is not LED definitions in the
dts and cannot configure these LEDs.
I Added missing LED definitions for WZR-900DHP.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds the PM8921 XOADC node to the PM8921 PMIC node,
defines the channels and further also define an IIO HWMON
node for the channels that are used for housekeeping of
voltages and die temperature for the PMIC chip die.
Tested on the Nexus 7 tablet:
lsiio
Device 000: PM8921-XOADC
cd /sys/bus/iio/devices/iio:device0
cat in_voltage10_input
616461 (0.625V reference voltage)
cat in_voltage11_input
(1.25V reference voltage)
cat temp1_input
35852 (die temperature)
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Using compatible strings without the <manufacturer> part for at24 is
now deprecated. Use a correct 'atmel,<model>' value.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Support the V1.2 hardware revision with the following pin muxing
changes:
Ddc_scl_pv4 and ddc_sda_pv5 previously used as Apalis GPIO3 and GPIO4
are now used as DDC pins.
Gen2_i2c_scl_pt5 and gen2_i2c_sda_pt6 previously used as DDC pins are
now used as USB power enable signals.
Usb_vbus_en0_pn4 and usb_vbus_en1_pn5 previously used as USB power
enable signals are now used as GPIO3 and GPIO4.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Apalis TK1 module uses some dedicated GPIOs as I210 gigabit Ethernet
controller reset and to control RESET_MOCI aka reset module output
carrier input on MXM3 pin 26. The Apalis Evaluation Board furthermore
uses Apalis GPIO7 on MXM3 pin 15 as reset signal for its PLX PEX 8605
PCIe Switch.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As the AS3722 GPIO0 is also a not connected on our Apalis TK1 module
explicitly configure it to high-impedance as well.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
