This patch fixes that sometimes hang at start-up time of the system.
As the below log:
...
[ 11.136543] calling pm_genpd_debug_init+0x0/0x60 @ 1
[ 11.141602] initcall pm_genpd_debug_init+0x0/0x60 returned 0 after 11 usecs
[ 11.148558] calling genpd_poweroff_unused+0x0/0x84 @ 1
<hang>
In some cases, the rk3399 should turn off the gmac power domain to save
power if some boards didn't register the gmac device node for rk3399.
Then, rk3399 need to make sure the gmac's pclk enabled if we need
operate the gmac power domain. (Due to the NOC had enabled always)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Initial device tree support for Qualcomm MSM8994 SoC and
Huawei Angler / Google Nexus 6P support.
The device tree is based on the Google 3.10 kernel tree.
The device can be booted into the initrd with only one CPU running.
Signed-off-by: Bastian Köcher <mail@kchr.de>
[jeremymc@redhat.com: removed Kconfig, defconfig, move from Huawei to qcom dir]
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Tested-by: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Initial device tree support for Qualcomm MSM8992 SoC and
LG Bullhead / Google Nexus 5X support.
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch add support to Analog audio both Playback and Capture via
msm8916 WCD muti codec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Pull PCI fixes from Bjorn Helgaas:
- Update MAINTAINERS for Intel VMD driver filename
- Update Rockchip rk3399 host bridge driver DTS and resets
- Fix ROM shadow problem that made some video device initialization
fail
* tag 'pci-v4.9-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: VMD: Update filename to reflect move
arm64: dts: rockchip: add three new resets for rk3399 PCIe controller
PCI: rockchip: Add three new resets as required properties
PCI: Don't attempt to claim shadow copies of ROM
Add the node for the thermal sensor of the bcm2837-soc
to the device tree.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
On the APQ8016 SBC, the LDO2 PM8916 regulator feeds 1.2V to the following:
- VDDA_1P2_MIPI_DSI and VDDA_MIPI_CSI pins on APQ8016.
- VCCCAD pins on the LPDDR3 chip.
- VDDPX_1 pins on APQ8016.
The LDO6 regulator feeds 1.8V to:
- VDAA_MIPI_DSI0_PLL pin on APQ8016.
- QFPROM_BLOW_VDD pin on PM8916.
- The AVDD, A2VDD and DVDD pins on ADV7533 bridge.
The LDO17 regulator feeds 3.3V to:
- The V3P3 pin on ADV7533 bridge.
Currently, the regulator min/max voltages for all the LDOs are set to the
range of what the PMIC supports. Set the ranges for L2, L6 and L17 to what
we need, i.e. 1.2V, 1.8V and 3.3V respectively.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
pm_rst, aclk_rst and pclk_rst should be controlled by driver, so we
need to add these three resets for PCIe controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
In drivers/mmc/core/host.c, there is "max-freqeuncy" property.
It should be same behavior, So Use the "max-frequency" instead of
"clock-freq-min-max".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enabling SPI controllers, which are attached to different busses
inside an SoC, may result in overlapping enumeration and cause
sysfs registration failure. Example log after enabling two
controllers on Armada 8040 SoC with same identifiers:
[ 3.740415] sysfs: cannot create duplicate filename
'/class/spi_master/spi0'
[ 3.747510] ------------[ cut here ]------------
[ 3.752145] WARNING: at fs/sysfs/dir.c:31
[...]
[ 4.002299] orion_spi: probe of f4700600.spi failed with error -17
spi-orion driver offers dedicated DT property ('cell-index'), that
allow setting unique identifiers. Recently added support for CP110-slave
HW block introduced two new SPI controllers' nodes with same ID as
ones from CP110-master.
This commit fixes the issue by assigning different 'cell-index' values
for CP110-slave SPI controllers.
Fixes: 4eef78a009 ("arm64: dts: marvell: add description for the slave
CP110 in Armada 8K")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
I2C and SPI interfaces share common clock trees within the CP110 HW block.
It occurred that SPI0 interface has wrong clock assignment in the device
tree, which is fixed in this commit to a proper value.
Fixes: c749b8d9de32 ("arm64: dts: marvell: add description for the ...")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add support for the AMAC ethernet to the Broadcom Northstar2 SoC device
tree
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using pinctrl-single,pins have #pinctrl-cells = <1>, while
pinctrl-single,bits need #pinctrl-cells = <2>.
Note that this patch can be optionally applied separately from the
driver changes as the driver supports also the legacy binding without
#pinctrl-cells.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These hardware blocks are SoC-specific, so their compatible strings
should be SoC-specific as well. This change has no impact on the
actual behavior since it is controlled by the generic "simple-mfd",
"syscon" compatible strings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a CPU clock to every CPU node and CPU OPP tables to use the
generic cpufreq driver. All the CPUs in each cluster share the
same OPP table.
Note:
clock-latency-ns (300ns) was calculated based on the CPU-gear switch
sequencer spec; it takes 12 clock cycles on the sequencer running
at 50 MHz, plus a bit additional latency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Add a CPU clock to every CPU node and a CPU OPP table to use the
generic cpufreq driver.
Note:
clock-latency-ns (300ns) was calculated based on the CPU-gear switch
sequencer spec; it takes 12 clock cycles on the sequencer running
at 50 MHz, plus a bit additional latency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The System Control node has 0x10000 byte of registers. The current
reg size must be expanded to use the cpufreq driver because the
registers controlling CPU frequency are located at offset 0x8000.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
At the first system bring-up, I chose to use spin-table because ARM
Trusted Firmware was not ready for this platform at that moment.
Actually, these SoCs are equipped with EL3 and able to provide PSCI.
Now I finished porting the ATF BL31 for the UniPhier platform, so it
is ready to migrate to PSCI enable method.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since this board doesn't mount pull-up/down registers for
USB1_{OVC,PWEN} pins, we should enable bias setting to pull these
pins up/down.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the exposed SD card slots in the DT of the r8a7796/salvator-x.
Based on work for the r8a7795/salvator-x by Ai Kyuse.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Interrupt of type IRQ_TYPE_NONE is not allowed for GIC interrupts and
generates an error:
genirq: Setting trigger mode 0 for irq 16 failed (gic_set_type+0x0/0x68)
The GIC requires shared interrupts to be edge rising or level high.
Platform declares support for both. Arbitrarily choose level high
everywhere hoping it will work on each platform.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Alban Browaeys <alban.browaeys@gmail.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
This patch adds the Device Tree source for Exynos5433-based Samsung TM2
board.
This patch adds support for following devices:
1. basic SoC
- Initial booting for Samsung Exynos5433 SoC
- DRAM LPDDR3 (3GB)
- eMMC (32GB)
- ARM architecture timer
2. power management devices
- Sasmung S2MPS13 PMIC for the power supply
- CPUFREQ for big.LITTLE cores
- TMU for big.LITTLE cores and GPU
- ADC with thermistor to measure the temperature of AP/Battery/Charger
- Maxim MAX77843 Interface PMIC (MUIC/Haptic/Regulator)
3. sound devices
- I2S for sound bus
- LPASS for sound power control
- Wolfson WM5110 for sound codec
- Maxim MAX98504 for speaker amplifier
- TM2 ASoC Machine device driver node
3. display devices
- DECON, DSI and MIC for the panel output
4. USB devices
- USB 3.0 DRD (Dual Role Device)
- USB 3.0 Host controller
5. storage devices
- MSHC (Mobile Storage Host Controller) for eMMC device
6. misc devices
- gpio-keys (power, volume up/down, home key)
- PWM (Pulse Width Modulation Timer)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Ingi kim <ingi2.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Pine64 is a cost-efficient development board based on the
Allwinner A64 SoC.
There are three models: the basic version with Fast Ethernet and
512 MB of DRAM (Pine64) and two Pine64+ versions, which both
feature Gigabit Ethernet and additional connectors for touchscreens
and a camera. Or as my son put it: "Those are smaller and these are
missing." ;-)
The two Pine64+ models just differ in the amount of DRAM
(1GB vs. 2GB). Since U-Boot will figure out the right size for us and
patches the DT accordingly we just need to provide one DT for the
Pine64+.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Maxime: Removed the common DTSI and include directly the pine64 DTS]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A64 SoC is a low-cost chip with 4 ARM Cortex-A53 cores
and the typical tablet / TV box peripherals.
The SoC is based on the (32-bit) Allwinner H3 chip, sharing most of
the peripherals and the memory map.
Although the cores are proper 64-bit ones, the whole SoC is actually
limited to 4GB (including all the supported DRAM), so we use 32-bit
address and size cells. This has the nice feature of us being able to
reuse the DT for 32-bit kernels as well.
This .dtsi lists the hardware that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
[Maxime: Convert to CCU binding, drop the MMC support for now]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Add a device node for the RST module, which provides a.o. reset control
and mode pin monitoring.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
There is a 'cpu-id' field in efuse, export it for other drivers
reference.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The devicetree node for mt8173-auxadc lacks the clock and
io-channel-cells property. This leads to a non-working driver.
mt6577-auxadc 11001000.auxadc: failed to get auxadc clock
mt6577-auxadc: probe of 11001000.auxadc failed with error -2
Fix these fields to get the device up and running.
Fixes: 748c7d4de4 ("ARM64: dts: mt8173: Add thermal/auxadc device
nodes")
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Correct regulator handling on Rockchip arm64 boards to make
bind/unbind calls work correctly and remove a sdio-only
property from non-sdio mmc hosts, that accidentially was
added there.
* tag 'v4.9-rockchip-dts64-fixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: remove the abuse of keep-power-in-suspend
arm64: dts: rockchip: remove always-on and boot-on from vcc_sd
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request contains a single fix for Broadcom ARM64-based SoCs:
- Ray adds the required bus width and OOB sector size properties to the
Northstar 2 SVK reference board in order for the NAND controller to work
properly
* tag 'arm-soc/for-4.9/devicetree-arm64-fixes' of http://github.com/Broadcom/stblinux:
arm64: dts: Updated NAND DT properties for NS2 SVK
Signed-off-by: Olof Johansson <olof@lixom.net>
The i.MX fixes for 4.9:
- A couple of patches from Fabio to fix the GPC power domain regression
which is caused by PM Domain core change 0159ec6707
("PM / Domains: Verify the PM domain is present when adding a
provider"), and a related kernel crash seen with multi_v7_defconfig
build.
- Correct the PHY ID mask for AR8031 to match phy driver code.
- Apply new added timer erratum A008585 for LS1043A and LS2080A SoC.
- Correct vf610 global timer IRQ flag to avoid warning from gic driver
after commit 992345a58e ("irqchip/gic: WARN if setting the
interrupt type for a PPI fails").
* tag 'imx-fixes-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: mach-imx6q: Fix the PHY ID mask for AR8031
ARM: dts: vf610: fix IRQ flag of global timer
ARM: imx: gpc: Fix the imx_gpc_genpd_init() error path
ARM: imx: gpc: Initialize all power domains
arm64: dts: Add timer erratum property for LS2080A and LS1043A
Signed-off-by: Olof Johansson <olof@lixom.net>
