bcm2837-rpi-3-b.dts, its only in-tree user, was overriding it as
"brcm,bcm2837" already.
Fixes: 9d56c22a78 ("ARM: bcm2835: Add devicetree for the Raspberry Pi 3.")
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch adds pmic specific dts which are configured specially
for db820c. One of such pin is GPIO_F on the Low Speed expansion
which has default output voltage of 2.7v. This patch fixes setup
for that pin to have an output voltage of 1.8v to comply with
96boards LS expansion specs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Hexagon core on the msm8916 provides services for audio control,
audio output, sensors and the Hexagon SDK. The Hexagon remoteproc node
allows us to boot this core.
Although its part of the core platform its left disabled as it will
crash without the rmtfs QMI service and we do not yet handle crashes
gracefully.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add clock controller nodes, including one top controller
two low speed controllers and one audio controller.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1046A QorIQ development system (QDS) board is a high-performance
computing, evaluation, development, and test platform supporting the
LS1046A SoC.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1046A reference design board (RDB) is a high-performance computing,
evaluation, and development platform that supports the LS1046A SoC.
Signed-off-by: Mingkai Hu <Mingkai.Hu@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Both the LS1043A and LS2080A platforms are affected by the Freescale
A008585 erratum. Advertise it in their respective device trees.
Signed-off-by: Scott Wood <oss@buserror.net>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Wifi module support on the Amlogic P20x boards on the SDIO port.
The Wifi module also needs a 32768Hz clock provided by the PWM E port
through a pwm-clock node in it's power sequence.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add a 32768Hz clock generated by the PWM E port used by the WiFi module.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add binding and basic support for the SD/eMMC controller on Amlogic
S905/GXBB devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added nodes for GX, enabled SDIO on P20x]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Adding QSPI node compatible with the new spi-bcm-qspi driver for the Broadcom's
Northstar2 SoC.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It was invented for sdio only, and should not be used for sdmmc
or emmc. Remove it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: Brian Kim <brian.kim@hardkernel.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
For boards only supporting 10/100 ethernet over a RMII PHY link, add
a separate pinctrl node. By the way, rename the existing node to rgmii
specific naming in all boards dts.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
In order to remove the boot warning :
[ 2.290933] Unable to detect cache hierarchy from DT for CPU 0
And add missing L2 cache hierarchy information, add a simple l2 cache node
and reference it from the A53 cpu nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch introduces the basic support for the Amlogic S905D (MesonGXL)
and for the Amlogic evaluation boards P230 and P231.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch introduces the basic support for the Amlogic S905X (Meson
GXL) and for the Amlogic evaluation board P212.
No documentation has been released yet for this SoC, so for now only the
bare minimum has been added in the DT.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
mvebu fixes for 4.8 (part 3)
- Select corediv clk for all mvebu v7 SoC
- Fix clocksource for CP110 master SPI0 for Armada 7K/8K
* tag 'mvebu-fixes-4.8-3' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: fix clocksource for CP110 master SPI0
ARM: mvebu: Select corediv clk for all mvebu v7 SoC
Signed-off-by: Olof Johansson <olof@lixom.net>
In case dr_mode isn't passed via DT, the dwc2 driver defaults
to OTG mode. But the Raspberry Pi 3 is designed only for host mode.
So fix this issue by linking to the dtsi file which set the dr_mode
to host.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Juno has separate MMU-401 instances in front of the DMA-330, both HDLCD
controllers, the USB host controller, the PCIe root complex, and the
CoreSight ETR. Since there is still work to do to make all the relevant
subsystems interact nicely with the presence of an IOMMU, add the nodes
to aid development and testing but leave them disabled by default to
avoid nasty surprises.
CC: Liviu Dudau <liviu.dudau@arm.com>
CC: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[sudeep.holla@arm.com: reformated subject]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
This is a high performance 64 bit dual core low power consuming
networking computing platform based on the ARMv8 architecture.
It contains an Armada 3720 running up to 1.2Ghz.
This commit adds a basic definition for this board.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
It can be used for the watchdog.
Based on similar work for r8a7795/salvator-x by Wolfram Sang.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The emmc on px5-evb can support hs200, so let's add mmc-hs200-1_8v.
And in order to speed up the boot time, we could add no-sdio and
no-sd to simplify the initialization.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI/BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The tcpc power domain will try to power up/down the power of Type-C PHY.
Hence, we need control it in Type-C PHY driver with the pm_runtime helper.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to the TRM and downstream code from rockchip, the register
address of i2c1 on rk3368 is 0xff660000 and i2c2 is 0xff140000.
This patch fix the i2c1 & i2c2 register address definition error, also
fix the clk and pinctrl reference error.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Please don't add these for vcc_sd, and mmc-core/driver will control
it. Otherwise, it will waste energy even without sdmmc in slot.
Moreover, it will causes a bug:
If we insert/remove sd card, we could see
[9.337271] mmc0: new ultra high speed SDR25 SDHC card at address 0007
[9.345144] mmcblk0: mmc0:0007 SD32G 29.3 GiB
This is okay for normal sd insert/remove test, but when I debug some
issues for sdmmc, I did unbind/bind test. And there is a interesting
phenomenon when we bind the driver again:
[58.314069] mmc0: new high speed SDHC card at address 0007
[58.320282] mmcblk0: mmc0:0007 SD32G 29.3 GiB
So the sd card could just support high speed without power cycle
since the vcc_sd is always on, which makes the sd card fail to
reinit its internal ocr mask.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull libata updates from Tejun Heo:
- Write same support added
- Minor ahci MSIX irq handling updates
- Non-critical SCSI command translation fixes
- Controller specific changes
* 'for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: qoriq: Revert "ahci: qoriq: Disable NCQ on ls2080a SoC"
libata: remove <asm-generic/libata-portmap.h>
libata: remove unused definitions from <asm/libata-portmap.h>
pata_at91: Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
ata: Replace BUG() with BUG_ON().
ata: sata_mv: Replacing dma_pool_alloc and memset with a single call dma_pool_zalloc.
libata: Some drives failing on SCT Write Same
ahci: use pci_alloc_irq_vectors
libata: SCT Write Same handle ATA_DFLAG_PIO
libata: SCT Write Same / DSM Trim
libata: Add support for SCT Write Same
libata: Safely overwrite attached page in WRITE SAME xlat
ahci: also use a per-port lock for the multi-MSIX case
ARM: dts: STiH407-family: Add ports-implemented property in sata nodes
ahci: st: Add ports-implemented property in support
ahci: qoriq: enable snoopable sata read and write
ahci: qoriq: adjust sata parameter
libata-scsi: fix MODE SELECT translation for Control mode page
libata-scsi: use u8 array to store mode page copy
Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
