Pull "mvebu dt64 for 4.10 (part 2)" from Gregory CLEMENT:
Fix DTC warning on Armada 37xx and 7K/8K
* tag 'mvebu-dt64-4.10-2' of git://git.infradead.org/linux-mvebu:
ARM64: dts: marvell: Fixup memory DT warning for Armada 37xx
arm64: dts: marvell: Fixup config-space DT warning For Armada 7K/8K
arm64: dts: marvell: Fixup internal-regs DT warning for Armada 37xx
This patch fixes the following DTC warning with W=1:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
This patch fixes the following DTC warning with W=1:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
This patch fixes the following DTC warning with W=1:
"Node /soc has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
TM2 can support the HS400 mode, but eMMC is working in the lowest mode.
This patch adds the properties for HS400 and other modes.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Following the Amlogic Linux kernel, it seem the only differences
between the GXL and GXM SoCs are the CPU Clusters.
This commit renames the gxl-s905d-p23x DTSI in a common file for
S905D p23x and S912 q20x boards.
Then adds a meson-gxm dtsi and reproduce the P23x to Q20x boards
dts files since the S905D and S912 SoCs shares the same pinout
and the P23x and Q20x boards are identical.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux 4.9-rc6
* tag 'v4.9-rc6': (305 commits)
Linux 4.9-rc6
ext4: sanity check the block and cluster size at mount time
fscrypto: don't use on-stack buffer for key derivation
fscrypto: don't use on-stack buffer for filename encryption
i2c: i2c-mux-pca954x: fix deselect enabling for device-tree
kvm: x86: merge kvm_arch_set_irq and kvm_arch_set_irq_inatomic
KVM: x86: fix missed SRCU usage in kvm_lapic_set_vapic_addr
KVM: async_pf: avoid recursive flushing of work items
kvm: kvmclock: let KVM_GET_CLOCK return whether the master clock is in use
KVM: Disable irq while unregistering user notifier
KVM: x86: do not go through vcpu in __get_kvmclock_ns
MAINTAINERS: Add LED subsystem co-maintainer
crypto: algif_hash - Fix NULL hash crash with shash
powerpc/mm: Fix missing update of HID register on secondary CPUs
KVM: arm64: Fix the issues when guest PMCCFILTR is configured
arm64: KVM: pmu: Fix AArch32 cycle counter access
powerpc/mm/radix: Invalidate ERAT on tlbiel for POWER9 DD1
i2c: digicolor: use clk_disable_unprepare instead of clk_unprepare
ipmi/bt-bmc: change compatible node to 'aspeed, ast2400-ibt-bmc'
Revert "drm/mediatek: set vblank_disable_allowed to true"
...
This pull request brings thermal support to the BCM2837 DT, and a few
other fixes.
In order to get the thermal node that we're adjusting the compatible
string on, we have to merge in the bcm2835-dt-next branch.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
PCI PHYs are missing from the Northstar2 DT entries for the 2 PCI buses.
Add them so that PCI devices can be discovered.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the mshc_2 node for supporting T-Flash.
Also add the "mshc*" aliases. dwmmc driver should be assigned to
"ctrl_id" after parsing to "mshc". If there are no aliases for mshc,
then it might be set to the wrong capabilities.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The "arm,no-tick-in-suspend" property was introduced to note
implementations where the system counter does not quite follow the ARM
specification that it "must be implemented in an always-on power
domain".
Particularly, RK3399's counter stops ticking when we switch from the
24MHz clock to the 32KHz clock in low-power suspend, so let's mark it as
such.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The NVIDIA P2771 is composed of a P3310 processor module that connects
to the P2597 I/O board. It comes with a 1200x1920 MIPI DSI panel that is
connected via the P2597's display connector and has several connectors
such as HDMI, USB 3.0, PCIe and ethernet.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The P3310 processor module comes ships with a firmware that implements
PSCI 1.0. Enable and use it to bring up all CPUs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA P3310 is a processor module used in several reference designs
that features a Tegra186 SoC, 8 GiB of LPDDR4 RAM, 32 GiB eMMC and other
essentials such as ethernet, WiFi and a PMIC. It is typically connected
to an I/O board (such as the P2597) that provides the connecters needed
to hook it up to the outside world.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has two GPIO controllers that are no longer compatible with the
controller found on earlier generations. One of these controllers exists
in an always-on partition of the SoC whereas the other can be clock- and
powergated.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has a total of four SDHCI controllers that each support SD 4.2
(up to UHS-I speed), SDIO 4.1 (up to UHS-I speed), eSD 2.1, eMMC 5.1 and
SDHOST 4.1 (up to UHS-I speed).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has a total of nine I2C controllers that are compatible with
the I2C controllers introduced in Tegra114. Two of these controllers
share pads with two DPAUX controllers (for AUX transactions).
Signed-off-by: Thierry Reding <treding@nvidia.com>
The initial patch only added UARTA, but there's no reason we shouldn't
be adding all of them. While at it, also specify the missing clocks and
resets for UARTA.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra186 has six CPUs: two CPUs are second generation Denver CPUs that
support ARMv8 and four CPUs are Cortex-A57 CPUs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This adds the initial support of Tegra186 SoC. It provides enough to
enable the serial console and boot from an initial ramdisk.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[treding@nvidia.com: remove leading 0 from unit-addresses]
[treding@nvidia.com: remove unused nvidia,bpmp property]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Product Register, which provides SoC product
and revision information.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This enables the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7796 SoC based M3ULCB low cost
board (R-Car Starter Kit Pro)
This commit supports the following peripherals:
- SCIF (console)
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Topic branch with DT arm64 changes for v4.10.
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
* tag 'samsung-dt64-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Use human-friendly symbols for interrupt properties in exynos7
arm64: dts: exynos: Fix invalid GIC interrupt flags in exynos7
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu dt64 for 4.10 (part 1)
Adding the new "community" board for Armada 3700
* tag 'mvebu-dt64-4.10-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: Add definition for the Globalscale Marvell ESPRESSOBin Board
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner arm64 DT changes for 4.10
Support for the Allwinner A64, their first armv8 SoC.
* tag 'sunxi-dt64-for-4.10' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
arm64: dts: add Pine64 support
Documentation: devicetree: add vendor prefix for Pine64
arm64: dts: add Allwinner A64 SoC .dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
ARM64: DT: Hisilicon SoC DT updates for 4.10
- Correct the hardware pin number of the usb node on the Hip06
- Add the Hisilicon Hip07 D05 board dts binding
- Add the initial dts for the Hip07 D05 board
- Fix the warning for the node without reg propery on the Hip06
- Fix the sas am max transmissions quirk property on the Hip06
- Disable the sas0 and sas2 on D03 board
- Add refclk node for SAS on the Hip06
* tag 'hisi-arm64-dt-4.10' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hisi: add refclk node to hip06 dts files for SAS
arm64: dts: hisi: disable sas0 and sas2 for d03
arm64: dts: hisi: fix hip06 sas am-max-trans quirk
arm64: dts: hip06: Fix no reg property warning
arm64: dts: hisilicon: Add initial dts for Hip07 D05 board
Documentation: arm64: Add Hisilicon Hip07 D05 dts binding
arm64: dts: hip06: Correct hardware pin number of usb node
Signed-off-by: Olof Johansson <olof@lixom.net>
Freescale arm64 device tree updates for 4.10:
- Enable Thermal Monitoring Unit (TMU) for thermal management on
LS1043A and LS2080A.
- Add support for LS1046A SoC, which has similar peripherals as
LS1043A but integrates 4 A72 cores.
- Add two LS1046A based board support: LS1046A-QDS and LS1046A-RDB.
* tag 'imx-dt64-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls2080a: Add TMU device tree support for LS2080A
arm64: dts: ls1043a: Add TMU device tree support for LS1043A
arm64: dts: add LS1046A-QDS board support
Documentation: DT: Add entry for QorIQ LS1046A-QDS board
arm64: dts: add LS1046A-RDB board support
Documentation: DT: Add entry for QorIQ LS1046A-RDB board
arm64: dts: add QorIQ LS1046A SoC support
dt-bindings: ahci-fsl-qoriq: updated for SoC ls1046a
dt-bindings: qoriq-clock: add LS1043A/LS1046A/LS2080A compatible for clockgen
dt-bindings: i2c: adds two more nxp devices
dt-bindings: fsl: add LS1043A/LS1046A/LS2080A compatible for SCFG and DCFG
dt-bindings: fsl: Add LS1043A/LS1046A/LS2080A SoC compatible strings
Signed-off-by: Olof Johansson <olof@lixom.net>
Add #pinctrl-cells for pinctrl-single using dts files. This allows
us to use generic parser later on. Note that the driver supports
handling the legacy binding also with no #pinctrl-cells so these
changes can be queued separately from the driver changes.
* tag 'omap-for-v4.10/pinctrl-cells-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add #pinctrl-cells for pinctrl-single instances
Signed-off-by: Olof Johansson <olof@lixom.net>
