Since the commit a526973e02 ("pinctrl: mvebu: Fix mapping of pin
63 (gpo -> gpio)"), the mpp63 is no more declared as a GPO but is a
GPIO. Even if in the datasheet this pin is described as GPO, the
experience of the D-Link DNS-327L board shows that it can be used as a
GPIO.
This commits generated warnings for the board using this pin as gpo, with
this patch the dts are fixed by using the new function (gpio) instead of
the old one.
The binding documentation has also been updated accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Using the usb-nop-xceiv PHY for the xhci nodes allows a better
representation of the hardware but also a better handling of the
regulator. By linking the regulator to the PHY there is no more need to
use the regulator-always-on property, then it allows a better power
management.
The remaining usb node uses the ehci-orion driver which can't be used
with the usb-nop-xceiv PHY and must keeps the direct link to the
regulator with the regulator-always-on property.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Really, what we meant by regulator-always-on is that the regulators
are already turned on by the bootloader, for which regulator-boot-on
is a better description.
A net advantage of using regulator-boot-on is that the regulator is
not touched at boot time by the kernel, which avoids having the hard
drives spinning down and then up again, taking several (~5) seconds of
additional boot time.
In addition, there is no need to have such properties on the child
regulators used for SATA. Having it on the parent regulator that
really controls the GPIO is sufficient.
Without the patch:
[ 3.945866] ata2: SATA link down (SStatus 0 SControl 300)
[ 3.995862] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.005863] ata4: SATA link down (SStatus 0 SControl 300)
[ 9.125861] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 9.144575] ata1.00: ATA-8: WDC WD5003ABYX-01WERA1, 01.01S02, max UDMA/133
[ 9.151471] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
(and you can hear the disk spinning down and up during this 5.1
seconds delay)
With the patch:
[ 3.945988] ata2: SATA link down (SStatus 0 SControl 300)
[ 4.005980] ata4: SATA link down (SStatus 0 SControl 300)
[ 4.011404] ata3: SATA link down (SStatus 0 SControl 300)
[ 4.145978] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.153701] ata1.00: ATA-8: WDC WD5003ABYX-01WERA1, 01.01S02, max UDMA/133
[ 4.160597] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As the name of the Device Tree file name suggests, the Armada 388 GP
really contains an Armada 388 SoC, so this commit updates the board
name and compatible string in the Device Tree file.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Pl330 integrated in rk3036 platform that doesn't support
DMAFLUSHP function. So we add 'arm,pl330-broken-no-flushp' quirk
for rk3036.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pl330 integrated in rk3xxx platform doesn't support
DMAFLUSHP function. So we add arm,pl330-broken-no-flushp quirk
for it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
pinctrl-sunxi uses 3 cells to describe interrupt, not 2. It's bank
number, pin number and flags.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to latest schematics [1], GPIO_1/VBUSDET
on TPS659038 is tied to AM57x GPIO4_21. We can use
that as a VBUS interrupt, instead of relying on
PMIC's VBUS interrupts which don't seem to be firing
on x15 at all.
A follow up patch will add support for using this
GPIO-based interrupt mechanism for notifying about
VBUS.
[1] https://github.com/beagleboard/beagleboard-x15/blob/master/BeagleBoard-X15_RevA2.pdf
Signed-off-by: Felipe Balbi <balbi@ti.com>
[cw00.choi: Use the 'vbus-gpio' property instead of 'interrupts-extended']
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The DTSI file for the Nomadik does not properly specify how the
PL180 levelshifter is connected: the Nomadik actually needs all
the five st,sig-dir-* flags set to properly control all lines out.
Further this board supports full power cycling of the card, and
since this variant has no hardware clock gating, it needs a
ridiculously low frequency setting to keep up with the ever
overflowing FIFO.
The pin configuration set-up is a bit of a mystery, because of
course these pins are a mix of inputs and outputs. However the
reference implementation sets all pins to "output" with
unspecified initial value, so let's do that here as well.
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The A83T does not have a 32.768 kHz low speed oscillator, either as
an external crystal or input. It has a 16 MHz RC-based (inaccurate)
internal oscillator, which is then divided by 512 for a clock close
to 32 kHz.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This connects the USB driver to the USB power domain, so that USB can
actually be turned on at boot if the bootloader didn't do it for us.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
This one is essentially the same as revision 2 B board (with the I2S on
P5 header).
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[anholt: Rebased on bcm2835.dtsi -> bcm283x.dtsi change]
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch fixes the naming of the device tree node: uart@7e201000
to conform to the standard of: serial@7e201000
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
[anholt: Rebased on 2835.dtsi -> 283x.dtsi change]
Signed-off-by: Eric Anholt <eric@anholt.net>
This enables the use of the auxiliary spi1 and spi2 devices
on the bcm2835 SOC.
Note that this requires the use of the new clk-bcm2835-aux to work.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[anholt: Rebased on 2835.dtsi -> 283x.dtsi change]
Signed-off-by: Eric Anholt <eric@anholt.net>
If we playback the 8KHz FS audio with the 256 mclk_fs, we need the
mclk = 256 * 8000 = 2.048MHz, the frac div is 594 / 2.048 = 290,
the frac div value 0x00809015 set to the CRU_CLKSEL7_CON will cause
to hang.
We increase the mclk_fs to 512, will get the mclk = 512 * 8000 =
4.096MHz, use 0x01009015 instead of 0x00809015 to work around this
issue. We will keep tracking it.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds the needed spi node for rk3036 dts.
We have to use the 4 bus emmc to work if someone want to support
the spi devices, since the pins are re-used by emmc data[5-8] and spi.
In some caseswe need to support the spi devices, that will waste the
emmc performance.
Moment, the kylin/evb hasn't the spi devices to work, so maybe we need wait
the new required to enable in kylin/evb board.
Anyway, the spi should be needed land in rk3036 dts.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The I2S block that provide the output clock as the mclk for rt5616,
That will be the master clock input.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
i2c3 and uart4 are available on the GPIO header. Though these pins only
have this one special function, the user may choose to use them as GPIOs
instead.
Since our policy is not to choose what function to present on the GPIO
headers of development boards, remove them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes for omaps with the most intrusive stuff being read-only data
assembly fixes, the other things are mostly board related:
- A series of omap assembly code fixes to fix issues with rodata with
ARM_KERNMEM_PERMS enabled. We had several places writing to rodata,
which is bad. The fix in most cases is to load the value from data
section using a pointer. Let's also enable ARM_KERNMEM_PERMS so
DEBUG_RODATA gets selected by default. And while testing things,
I also added few more loadable driver modules to the defconfig that
I seem to need quite often.
- Fix a long standing omap5 RTC mystery and enable RTC where we need
to ensure the SoC msecure pin is high so we can write to the RTC
registers.
- Fix irq types for am437x
- A series of minor dts fixes for sbc-am57x and cl-som-am57x
- Fixes for torpedo dts to make WLAN behave and to remove a duplicate
i2c rate entry
This series also includes few minor changes that are not stricly
fixes, but would be good to get in during the early -rc cycle:
- Remove legacy mailbox platform data that is no longer needed
- Add the pdata-quirks needed for the new pwm-omap-dmtimer so
people can use it
- Enable ti,mbox-send-noirq that's needed by wkup_m3 driver
- Enable SPLIT and DWARF4 in omap2plus_defconfig as it makes the
initramfs quite a bit smaller
* tag 'omap-for-v4.5/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (23 commits)
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: Fix wl12xx missing clocks that cause hangs
ARM: OMAP: Add PWM dmtimer platform data quirks
ARM: omap2plus_defconfig: Enable ARM_KERNMEM_PERMS and few loadable modules
ARM: OMAP2+: Fix ppa_zero_params and ppa_por_params for rodata
ARM: OMAP2+: Fix l2_inv_api_params for rodata
ARM: OMAP2+: Fix save_secure_ram_context for rodata
ARM: OMAP2+: Fix l2dis_3630 for rodata
ARM: OMAP2+: Fix wait_dll_lock_timed for rodata
ARM: OMAP2+: Remove legacy mailbox device instantiation
ARM: dts: AM4372: Add ti,mbox-send-noirq to wkup_m3 mailbox
ARM: dts: AM33xx: Add ti,mbox-send-noirq to wkup_m3 mailbox
...
Signed-off-by: Olof Johansson <olof@lixom.net>
As the kylin schematic drawing, add the needed work led for
kylin board.
Run:
echo 0 > /sys/class/leds/kylin:red:led/brightness
echo 1 > /sys/class/leds/kylin:red:led/brightness
The led can normal on/off on kylin board.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable audio DMAC (= rcar-dmac) in r8a7793 device tree.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
v4
* Use GIC_SPI in interrupts properties
Enable DMA transfer using DVC in r8a7793/gose device tree.
DMA DMApp
[MEM] -> [SRC] -> [DVC] -> [SSIU] -> [SSI]
DMA DMApp
[MEM] <- [DVC] <- [SRC] <- [SSIU] <- [SSI]
Based on similar work for the r8a7791/koelsch by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable DMA transfer to/from SRC in r8a7793/gose device tree.
DMA DMApp
[MEM] -> [SRC] -> [SSIU] -> [SSI]
DMA DMApp
[MEM] <- [SRC] <- [SSIU] <- [SSI]
Current sound driver is supporting
SSI/SRC random connection.
So, this patch is tring
SSI0 -> SRC2
SSI1 <- SRC3
Based on similar work for the r8a7791/koeslch by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable DMA transfer to/from SSIU in gose/r8a7791 device tree.
DMA
[MEM] -> [SSIU] -> [SSI]
DMA
[MEM] <- [SSIU] <- [SSI]
Based on similar work for the r8a7791/koelsch by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable DMA transfer to/from SSI in r8a7793/gose device tree.
DMA
[MEM] -> [SSI]
DMA
[MEM] <- [SSI]
Based on similar work for the r8a7791/koelsch by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate R-Car sound node in r8a7793 device tree.
This only supports PIO transfers.
Based on similar work for the r8a7791 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Porter board dependent part of the R8A7791 sound device node.
Add device node for Asahi Kasei AK4642 stereo codec to the I2C2 bus.
Add the "simple-audio-card" device node to interconnect the SoC sound
device and the codec.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds r8a7793 GOSE HDMI video out support.
The r8a7793 GOSE board is similar to r8a7791 Koelsch. For those
boards an on-board HDMI encoder chip provides HDMI video out
and also a LVDS port is available for external LCD panels.
Tested on r8a7793 Gose with HDMI hooked up to a Toshiba TV.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[simon: rebased; reused existing i2c2 node]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux-keypad,wakeup" boolean property to enable the
wakeup source, "wakeup-source" is the new standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Add support for restoring GScaler parent clocks configuration when GSCL
power domain is turned on.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fix CPU operating points for Exynos5800 (it use different
voltages than Exynos5420 and supports additional frequencies).
However don't use 2000MHz & 1900MHz OPPs (for A15 cores) and
1400MHz OPP (for A7 cores) for now as they are not available
on all boards.
Based on Hardkernel's kernel for ODROID-XU3 board.
Changes by Ben Gamari:
- Port to operating-points-v2
Cc: Doug Anderson <dianders@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Andreas Faerber <afaerber@suse.de>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
