The SNVS poweroff depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up to external PMIC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fixes for omap variants
Three fixes mostly for dra7 SoC variants that have some devices disabled
compared to the base SoC. These got broken by the change of making devices
probe with ti-sysc interconnect target module and went unnnoticed for a
while. And there is no clkcel bit for timer12 unlike timer1. Also included
is a GPIO direction fix for phytec SDIO card detection.
* tag 'omap-for-v5.2/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x phytec boards: Fix cd-gpios active level
ARM: dts: dra72x: Disable usb4_tm target module
ARM: dts: Drop bogus CLKSEL for timer12 on dra7
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.2-rc1, please pull the following:
- Florian fixes the remaining Broadcom DTS files to have a valid
device_type = "memory" property which was missed during the removal of
skeleton.dtsi
* tag 'arm-soc/for-5.2/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: Add missing device_type = "memory" property
Signed-off-by: Olof Johansson <olof@lixom.net>
Fixes for omap variants for dra7 mmc voltage and boot issues
This series contains dra7 mmc voltage fixes, and fixes to the recent
changes to probe devices with device tree data insteas of legacy
platform data:
- Two fixes for dra7 mmc that needs 1.8V mode disabled as in case of a
reset, the bootrom will try to access the mmc card at 3.3V potentially
damaging the card
- Two regression fixes for am335x d_can. We must allow devices with no
control registers for ti-sysc interconnect target module driver for
at least d_can, and we remove the incorrect control registers for
d_can. And we must configure the osc clock for d_can as otherwise
register access may fail depending on the bootloader version
- Four regression fixes for dra7 variant dts files to tag rtc and usb4
as disabled for dra71x and dra76x. These SoC variants do not have
these devices, and got accidentally enabled when the L4 interconnect
got defined in the dra7-l4.dtsi for the dra7 SoC family
* tag 'omap-for-v5.2/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra71x: Disable usb4_tm target module
ARM: dts: dra71x: Disable rtc target module
ARM: dts: dra76x: Disable usb4_tm target module
ARM: dts: dra76x: Disable rtc target module
ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values
ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
bus: ti-sysc: Handle devices with no control registers
ARM: dts: Configure osc clock for d_can on am335x
Signed-off-by: Olof Johansson <olof@lixom.net>
Add initial support for the display found on the LG Nexus 5 (hammerhead)
phone. This is based on work from Jonathan Marek.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the MDP5, DSI and DSI PHY blocks for the display found on the
msm8974 SoCs. This is based on work from msm8916.dtsi and Jonathan
Marek.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable cpufreq-dt support for da850-evm. The cvdd is supplied by the
tps65070 pmic with configurable output voltage. By default da850-evm
boards support frequencies up to 375MHz so enable this operating
point.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a fixed regulator for the da850-lcdk board along with board-specific
CPU configuration.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a fixed regulator for the LEGO EV3 board along with board-specific
CPU configuration.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds a cpu node and operating points to the common da850.dtsi file.
All operating points above 300MHz are disabled by default.
Regulators need to be hooked up on a per-board basis.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This enables wake up on Bluetooth activity when the device is
suspended. The BT_HOST_WAKE signal is only connected on devices
with BT module that are connected through UART.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
It has two regular Ethernet ports and four switched, TSN-capable ports.
It also features:
- One Arduino header
- One expansion header
- Two USB 3.0 ports
- One mini PCIe slot
- One SATA interface
- Accelerometer, gyroscope, temperature sensors
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Allows to use the SD interface at a higher speed mode if the card
supports it. For this the signaling voltage is switched from 3.3V to
1.8V under the usdhc1's drivers control.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to latest docs imx7d chips can go from 800 to 1200 mhz.
Maximum frequency is determined from two speed grading bits present in
OCOTP fuses at same location as other imx chips.
Also update to "typical" voltages from latest datasheet, 25mv higher
than current dts.
All imx7s parts are still fixed at 800mhz
Based on:
* IMX7DCEC Rev. 6, 03/2019
* IMX7SCEC Rev. 6, 03/2019
* IMX7DRM Rev. 1, 01/2018 Page 1102
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i2c2 bus has a external plug which enables the easy connection of external
"bricks" with sensors of various kinds, while i2c4 on the Extended/Full boards
has a pair of on board motion sensors, accelerometer and magnetometer on one chip
and gyroscope on another so it makes sense to enable these i2c buses for use.
Tested on UDOO Neo Full.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Baltos 5221/3220 devices provide CD signal on GPIO2_18.
Baltos 2110 device provides CD signal on GPIO1_15.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PHY must add both tx and rx delay and not only on the tx clock.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the ADC from exynos5420.dtsi to a shared file between Exynos5410 and
Exynos542x: exynos54xx.dtsi. Enable the ADC on Odroid XU board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add the EMAC's OCP reset property on Arria10. The OCP reset bits are
also needed to correctly bring the EMACs out of reset correctly.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add the two ltc2497 devices that are on the SoCFPGA Arria10
Socdk board at addresses 0x14 and 0x16.
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Default values fit better than these historical settings.
Hardware layout had been adapted accordingly already in
alpha stage. They did not cause problems for a long time.
Removed values now.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename user led nodes to match the phytec user leds name scheme.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As nand flash is not always the primary storage device any more
disable it in the phycore-som include file. Enable it the device tree
files where it is populated.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phyCORE-AM335x EMMC modules have an EMMC populated and are based
on the phyCORE-AM335x R2 SOM. Therefore, the EMMC node will be added to
the phycore-som devce tree but is by default disabled.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move regulators directly to the root node like most am335x boards do.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are two LCD device released by Logic PD for the Torpedo,
type 15 and Type 28. The stock dts file supports the older LCD,
so this patch enables support for the newer one.
For details between these different LCD's see
https://support.logicpd.com/DesktopModules/Bring2mind/DMX/Download.aspx?portalid=0&EntryId=2777
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: removed extra blank line for checkpatch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Active level of the mmc1 cd gpio needs to be low instead of high.
Fix PCM-953 and phyBOARD-WEGA.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
usb4_tm is unsed on dra72 and accessing the module
with ti,sysc is causing a boot crash hence disable its target
module.
Fixes: 549fce068a ("ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data")
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel,
so can dismiss warning during initialisation.
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel and
static replicator, so can dismiss warning during initialisation.
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Because of register and bits difference for setting PHY modes, PTP reference
clock, and FPGA signalling, the Arria10 SoC needs to use the
"altr,socfpga-stmmac-a10-s10" binding to set the correct modes.
On Arria10, each EMAC has its own register for PHY modes, and they all have
the same offset, thus we can use the 2nd parameter to specify the offsets
for the FPGA signal bits.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Unlike what's being reported in the device tree so far, the RTC in the R40
is quite different from the H3. Indeed it doesn't have the internal
oscillator output, and it has only a single interrupt. Let's add a
compatible for it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The V3s datasheet mandates oscillators accuracy to be within 50ppm. Let's
add that accuracy to their device tree nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
For some reason, while the v3s has a dedicated compatible in the RTC
binding, the one actually used was the A31's. However, it turns out that
the controller is pretty different (which justified the compatible).
Let's use the proper compatible, and use the proper binding description as
well.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A31 datasheet mandates oscillators accuracy to be within 50ppm. Let's
add that accuracy to their device tree nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The RTC node doesn't match what is described in the binding for historical
reasons. Let's add the proper description.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
