The change to include ibm-power9-cfam.dtsi resulted in a renumbering
of all of the I2C bus numbers behind the on-board muxes. This breaks
some tools which have hardcoded the bus numbers.
Add device tree aliases for the I2C buses routed through the PCIe slots
so that they return to their former numbers before the cfam change.
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The I2C address of the brick is different depending on the board SKU.
Update the values to instantiate addresses which work for most boards.
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the aspeed-p2a-ctrl node and configure with memory-region to
enable mmap access.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a node for the aspeed-p2a-ctrl module. This node, when enabled will
disable the PCI-to-AHB bridge and then allow control of this bridge via
ioctls, and access via mmap.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
To be used by the OpenPower BMC machines.
This provides proper chip IDs but also adds the various sub-devices
necessary for the future OCC driver among other. All the added nodes
comply with the existing upstream FSI bindings.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The device tree compiler has started spitting out warnings about these
names, insisting they be called 'spi':
../arch/arm/boot/dts/aspeed-g5.dtsi:108.35-128.5: Warning
(spi_bus_bridge): /ahb/flash-controller@1e631000: node name for SPI
buses should be 'spi'
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add video capture support from the OV5642 to IPU CSI0 on
the i.MX53 SMD.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
[fabio: remove unnecessary 'regulator-always-on' from camera regulators]
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add video capture_subsystem device node, and include both CSI ports.
Prepare for adding sensors by adding the parallel sensor anchor endpoints
to the CSI ports.
Signed-off-by: Steve Longerbeam <slongerbeam@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DCDC2 regulator output is actually called "VDD_EE" in various
Meson8b board schematics. This matches with what Amlogic names it in the
most part of their vendor kernel (there are a few places where it's
actually called VDDAO, schematics of EC-100 suggest that the regulator
output is used for both signals).
While here, also give the regulator an alias as it supplies the Mali GPU
so a phandle to it will be required later on.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the canvas module to Meson8b because it's required for the VPU
(video output) and video decoders.
The canvas module is located inside the "DMC bus" (where also some of
the memory controller registers are located). The "DMC bus" itself is
part of the so-called "MMC bus".
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
With the Meson8m2 SoC the canvas module was moved from offset 0x20
(Meson8) to offset 0x48 (same as on Meson8b). The offsets inside the
canvas module are identical.
Correct the offset so the driver uses the correct registers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the canvas module to Meson8 because it's required for the VPU
(video output) and video decoders.
The canvas module is located inside thie "DMC bus" (where also some of
the memory controller registers are located). The "DMC bus" itself is
part of the so-called "MMC bus".
Amlogic's vendor kernel has an explicit #define for the "DMC" register
range on Meson8m2 while there's no such #define for Meson8. However, the
canvas and memory controller registers on Meson8 are all expressed as
"0x6000 + actual offset", while Meson8m2 uses "DMC + actual offset".
Thus it's safe to assume that the DMC bus exists on both SoCs even
though the registers inside are slightly different.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
mickey crams a lot of hardware into a tiny package, which requires
more aggressive thermal throttling than for devices with a larger
footprint. Configure the GPU thermal zone to throttle the GPU
progressively at temperatures >= 60°C. Heat dissipated by the
CPUs also affects the GPU temperature, hence we cap the CPU
frequency to 1.4 GHz for temperatures above 65°C. Further throttling
of the CPUs may be performed by the CPU thermal zone.
The configuration matches that of the downstream Chrome OS 3.14
kernel, the 'official' kernel for mickey.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On rk3288 the CPU and GPU temperatures are correlated. Limit the GPU
frequency on veyron mickey to 400 MHz for CPU temperatures >= 65°C
and to 300 MHz for CPU temperatures >= 85°C.
This matches the configuration of the downstream Chrome OS 3.14 kernel,
the 'official' kernel for mickey.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NPLL is the only safe way to generate 500 MHz for the GPU. The
downstream Chrome OS 3.14 kernel ('official' kernel for veyron
devices) re-purposes NPLL to HDMI and hence disables the OPP for
the GPU (see https://crrev.com/c/1574579). Disable it here as well
to keep in sync and avoid problems in case someone decides to
re-purpose NPLL.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
[moved from veyron to general rk3288, as tying up the NPLL for a
not-that-helpful opp (not really fast but will still generate
quite a bit of heat) doesn't make so much sense when it will
keep us from supporting other display modes in the future]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently the CPUs are used as cooling devices of the rk3288 GPU
thermal zone. The CPUs are also configured as cooling devices in the
CPU thermal zone, which indirectly helps with cooling the GPU thermal
zone, since the CPU and GPU temperatures are correlated on the rk3288.
Configure the ARM Mali Midgard GPU as cooling device for the GPU
thermal zone instead of the CPUs.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Mali GPU of the rk3288 can be used as cooling device, add
a #cooling-cells entry for it.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is similar to commit e6186820a7 ("arm64: dts: rockchip: Arch
counter doesn't tick in system suspend"). Specifically on the rk3288
it can be seen that the timer stops ticking in suspend if we end up
running through the "osc_disable" path in rk3288_slp_mode_set(). In
that path the 24 MHz clock will turn off and the timer stops.
To test this, I ran this on a Chrome OS filesystem:
before=$(date); \
suspend_stress_test -c1 --suspend_min=30 --suspend_max=31; \
echo ${before}; date
...and I found that unless I plug in a device that requests USB wakeup
to be active that the two calls to "date" would show that fewer than
30 seconds passed.
NOTE: deep suspend (where the 24 MHz clock gets disabled) isn't
supported yet on upstream Linux so this was tested on a downstream
kernel.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is like the same change for rk3288-veyron-minnie. See that patch
for more details.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We can now use the "gpio-line-names" property to provide the names for
all the pins on a board. Let's use this to provide the names for all
the pins on rk3288-veyron-minnie.
In general the names here come straight from the schematic. That
means even if the schematic name is weird / doesn't have consistent
naming conventions / has typos I still haven't made any changes.
The exception here is for two pins: the recovery switch and the write
protect detection pin. These two pins need to have standardized names
since crossystem (a Chrome OS tool) uses these names to query the
pins. In downstream kernels crossystem used an out-of-tree driver to
do this but it has now been moved to the gpiod API and needs the
standardized names.
It's expected that other rk3288-veyron boards will get similar patches
shortly.
NOTE: I have sorted the "gpio" section to be next to the "pinctrl"
section since it seems to logically make the most sense there.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Remove the child nodes of the sckc as they are not necessary anymore.
Also, switch to the new atmel,sama5d3-sckc compatible string to use the
proper startup time for the RC oscillator (500 µs instead of 75).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The SPI controller bindings require an address cell size of 1, and a size
cell size of 0. Let's put it at the DTSI level to make sure that's properly
enforced.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The chosen clocksource and clockevent bindings have never been accepted and
parsed, remove them.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Enable OV5640 camera sensor driver of MB1379A extension
board connected on CN7 connector of stm32mp157c-ev1 board:
bus-width is set to 8, data-shift is set to 2 (lines 9:2 are used),
hsync-active is set to 0 for horizontal synchro line active low,
vsync-active is set to 0 for vertical synchro line active low and
pclk-sample is set to 1 for pixel clock polarity sampling data
on rising edge of the pixel clock signal.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
51 franklin street fifth floor boston ma 02110 1301 usa
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option [no]_[pad]_[ctrl] any later version this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not write to the free
software foundation inc 51 franklin street fifth floor boston ma
02110 1301 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 176 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.652910950@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds jedec compatible for spi-nor flash
on stm32mp157c-ev1 (needed with new spi-mem interface).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The joystick (B1) on stm32mp157c-ev1 uses gpios on STMFX gpio expander.
These gpios need a pin configuration (push-pull and bias-pull-down),
described under stmfx_pinctrl node.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
