These settings are needed to make the hardware operable.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The PEN2 line needs to be pulled up for the charger to enter high-current
mode. Do this with a static pull on the GPIO.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The dock detection input key is active low. Also add a pinmux for it.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This allows users of the pinctrl driver to specify either
pinctrl-single,bias-pullup = MPF_PULL_UP;
or
pinctrl-single,bias-pulldown = MPF_PULL_DOWN;
To activate the pull bits in the MFP registers.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
warnings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes a number of unit_address_vs_reg warnings:
DTC arch/arm/boot/dts/bcm7445-bcm97445svmb.dtb
arch/arm/boot/dts/bcm7445.dtsi:66.6-225.4: Warning (unit_address_vs_reg): /rdb: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445.dtsi:227.21-298.4: Warning (unit_address_vs_reg): /memory_controllers: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445-bcm97445svmb.dts:9.9-14.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445.dtsi:255.10-275.5: Warning (simple_bus_reg): /memory_controllers/memc@1: simple-bus unit address format error, expected "80000"
arch/arm/boot/dts/bcm7445.dtsi:277.10-297.5: Warning (simple_bus_reg): /memory_controllers/memc@2: simple-bus unit address format error, expected "100000"
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
On disco and eval board, Tx and Rx delay are applied (pull-up of 4.7k
put on VDD) so which correspond to RGMII-ID mode with internal RX and TX
delays provided by the PHY, the MAC should not add the RX or TX delays
in this case
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add devicetree support for Avenger96 board based on STM32MP157A MPU
from ST Micro. This board is one of the 96Boards Consumer Edition board
from Arrow Electronics and has the following features:
SoC: STM32MP157AAC
PMIC: STPMIC1A
RAM: 1024 Mbyte @ 533MHz
Storage: eMMC v4.51: 8 Gbyte
microSD Socket: UHS-1 v3.01
Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant
Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
Bluetooth®v4.2 (BR/EDR/BLE)
USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG
Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4
LED: 4x User LED, 1x WiFi LED, 1x BT LED
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add identification registers to address range
of SAI DT parent node, for stm32mp157c.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds a new property (power-supply) to panel rm68200 (raydium)
on stm32mp157c-ev1.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit d6cd33ad71 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes: 9eb36b945b ("ARM: dts: iwg23s-sbc: Add uSD and eMMC support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit d6cd33ad71 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes: 029efb3a03 ("ARM: dts: iwg20d-q7: Add SDHI1 support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for input switch SW3 on the Renesas RZ/A2M EVB
development board.
Note that this uses the IRQ interrupt, as the RZ/A2 GPIO controller
does not include interrupt support
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the IRQC on RZ/A2M, which is a small front-end to the
GIC. This allows to use up to 8 external interrupts with configurable
sense select.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch sorts the nodes of arch/arm/boot/dts/r7s9210-rza2mevb.dts.
* Sort subnodes of root ("/") node alphabetically
* Sort following top-level nodes alphabetically
* Sort subnodes of pinctrl alphabetically
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[simon: rebase and sort new ehci nodes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The snps,reset-gpio bindings are deprecated in favour of the generic
"Ethernet PHY reset" bindings.
Replace snps,reset-gpio from the ðmac node with reset-gpios in the
ethernet-phy node. The old snps,reset-active-low property is now encoded
directly as GPIO flag inside the reset-gpios property.
snps,reset-delays-us is converted to reset-assert-us and
reset-deassert-us. reset-assert-us is the second cell from
snps,reset-delays-us while reset-deassert-us was the third cell.
Instead of blindly copying the old values (which seems strange since
they gave the PHY one second to come out of reset) over this also
updates the delays based on the datasheets:
- RTL8211F PHY on the Odroid-C1 and MXIII-Plus needs a 10ms assert
delay (the datasheet mentions: "For a complete PHY reset, this pin
must be asserted low for at least 10ms") and a 30ms deassert delay
(the datasheet mentions: "Wait for a further 30ms (for internal
circuits settling time) before accessing the PHY register"). The
old settings used 10ms for assert and 1000ms for deassert.
- IP101GR PHY on the EC-100 and MXQ needs a 10ms assert delay (the
datasheet mentions: "Trst | Reset period | 10ms") and a 10ms deassert
delay as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock
output ready after reset released | 10ms")). The old settings used
10ms for assert and 1000ms for deassert.
No functional changes intended.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the video engine and add it's optional reserved memory region.
Use 32MB for the reserved memory since the video engine could need up to
two 1920x1200@32bpp source buffers.
Source buffers: 2 * 1920 * 1200 * 4 = 18432000 bytes
In addition, the V4L2 subsystem will allocate any number of compression
buffers, each at most 1/8th the size of the source buffer.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Move SoC-specific PMU properties from exynos4.dtsi to respective SoC
(4210 or 4412) so common DTSI would have only common properties.
Define there also interrupt affinity to remove the boot warning message:
hw perfevents: no interrupt-affinity property for /pmu, guessing.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Galaxy S3 boards use an aat1290 to control the flash LED. Add the
relevant device tree configuration to use it.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> [rebase]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
SoCFPGA DTS updates for v5.3
- Use the new "altr,socfpga-stmmac-a10-s10" for the EMAC controllers on
Arria10/Stratix10
- Add the ltc2497 i2c entry on the Arria10 devkit
- Add the EMAC OCP reset property on the Arria10
* tag 'socfpga_dts_updates_for_v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: arria10: Add EMAC OCP reset property
ARM: dts: socfpga: add ltc2497 on arria10 devkit
arm64: dts: stratix10: use the "altr,socfpga-stmmac-a10-s10" binding
ARM: dts: socfpga: use the "altr,socfpga-stmmac-a10-s10" binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes up two issues with the Gemini DTS files:
- Blank console after a while on the DIR-685 so as
not to waste power
- Fix up the erroneous compatible string on the DNS-313
* tag 'gemini-dts-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: gemini Fix up DNS-313 compatible string
ARM: dts: Blank D-Link DIR-685 console
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung DTS ARM changes for v5.3
1. Fixes for minor warnings.
2. Enable ADC on Exynos5410 Odroid XU board.
* tag 'samsung-dt-5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add ADC node to Exynos5410 and Odroid XU
ARM: dts: exynos: Raise maximum buck regulator voltages on Arndale Octa
ARM: dts: exynos: Move CPU OPP tables out of SoC node on Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
ARMv7 Vexpress updates for v5.3
1. Couple of updates switching to use new/updated bindings for CoreSight
dynamic funnel components and NOR flash partition type
2. Disable NOR flash on Vexpress TC2 platform as it conflicts with CPU
power management. This follows what we have on ARMv8 Juno platform
and is required after recent commit that enabled CFI NOR FLASH in
multi_v7 defconfig
* tag 'vexpress-updates-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: set the right partition type for NOR flash
arm: dts: vexpress-v2p-ca15_a7: disable NOR flash node by default
ARM: dts: vexpress-v2p-ca15_a7: update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
ti-sysc dts changes for v5.3
We can now drop the custom dts property "ti,hwmods" for drivers that
have the ti-sysc interconnect target module configured in dts.
Let's start with a minimal changes to omap4 uart and mmc. We use
omap4 as the starting point as it has runtime PM implemented and all
the omap variants after that are based on it with similar clkctrl
clock for the modules. More devices will be updated later on as they
get tested.
Note that these changes are based on the related ti-sysc driver
changes.
* tag 'omap-for-v5.3/ti-sysc-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: Drop legacy custom hwmods property for omap4 mmc
ARM: dts: Drop legacy custom hwmods property for omap4 uart
bus: ti-sysc: Detect uarts also on omap34xx
bus: ti-sysc: Do rstctrl reset handling in two phases
bus: ti-sysc: Add support for disabling module without legacy mode
bus: ti-sysc: Set ENAWAKEUP if available
bus: ti-sysc: Handle swsup idle mode quirks
bus: ti-sysc: Handle clockactivity for enable and disable
bus: ti-sysc: Enable interconnect target module autoidle bit on enable
bus: ti-sysc: Allow QUIRK_LEGACY_IDLE even if legacy_mode is not set
bus: ti-sysc: Make OCP reset work for sysstatus and sysconfig reset bits
bus: ti-sysc: Support 16-bit writes too
bus: ti-sysc: Add support for missing clockdomain handling
ARM: dts: dra71x: Disable usb4_tm target module
ARM: dts: dra71x: Disable rtc target module
ARM: dts: dra76x: Disable usb4_tm target module
ARM: dts: dra76x: Disable rtc target module
ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values
ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
bus: ti-sysc: Handle devices with no control registers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
dts changes for omap variants for v5.3
This series of changes improves support for few boards:
- configure another lcd type for logicpd torpedo devkit
- a series of updates for am335x phytec boards
- configure mmc card detect pin for am335x-baltos
* tag 'omap-for-v5.3/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-baltos: add support for MMC1 CD pin
ARM: dts: am335x-baltos: Fix PHY mode for ethernet
ARM: dts: Add support for phyBOARD-REGOR-AM335x
ARM: dts: am335x-pcm-953: Remove eth phy delay
ARM: dts: am335x-pcm-953: Update user led names
ARM: dts: am335x-phycore-som: Enable gpmc node in dts files
ARM: dts: am335x-phycore-som: Add emmc node
ARM: dts: am335x phytec boards: Remove regulator node
ARM: dts: Add LCD type 28 support to LogicPD Torpedo DM3730 devkit
Signed-off-by: Olof Johansson <olof@lixom.net>
A lot more love for rk3288 in general and veyron specially with changes
all over the place.
* tag 'v5.3-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (21 commits)
ARM: dts: rockchip: Split GPIO keys for veyron into multiple devices
ARM: dts: rockchip: Add HDMI i2c unwedging for rk3288-veyron
ARM: dts: rockchip: Add unwedge pinctrl entries for dw_hdmi on rk3288
ARM: dts: rockchip: Switch to builtin HDMI DDC bus on rk3288-veyron
ARM: dts: rockchip: Add pin names for rk3288-veyron jaq, mickey, speedy
ARM: dts: rockchip: fix pwm-cells for rk3288's pwm3
ARM: dts: rockchip: Configure the GPU thermal zone for mickey
ARM: dts: rockchip: Use the GPU to cool CPU thermal zone of veyron mickey
ARM: dts: rockchip: remove GPU 500 MHz OPP on rk3288
ARM: dts: rockchip: Use GPU as cooling device for the GPU thermal zone of the rk3288
ARM: dts: rockchip: Add #cooling-cells entry for rk3288 GPU
ARM: dts: rockchip: Mark that the rk3288 timer might stop in suspend
ARM: dts: rockchip: Add pin names for rk3288-veyron-jerry
ARM: dts: rockchip: Add pin names for rk3288-veyron-minnie
ARM: dts: raise GPU trip point temperature for speedy to 80 degC
ARM: dts: rockchip: raise GPU trip point temperatures for veyron
ARM: dts: rockchip: raise CPU trip point temperature for veyron to 100 degC
ARM: dts: rockchip: Make rk3288-veyron-minnie run at hs200
ARM: dts: rockchip: Make rk3288-veyron-mickey's emmc work again
ARM: dts: rockchip: Remove bogus 'i2s_clk_out' from rk3288-veyron-mickey
...
Signed-off-by: Olof Johansson <olof@lixom.net>
It's a simple typo in the DNS file, which was pretty serious.
No scripts were working properly. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Leaving this NAS with display and backlight on heats it up
and dissipates power. Turn off the screen after 4 minutes,
it comes back on when a user touches the keys.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We want to be able to wake from USB if a device is plugged in that
wants remote wakeup. Enable it on both dwc2 controllers.
NOTE: this is added specifically to veyron and not to rk3288 in
general since it's not known whether all rk3288 boards are designed to
support USB wakeup. It is plausible that some boards could shut down
important rails in S3.
Also note that currently wakeup doesn't seem to happen unless you use
the "deep" suspend mode (where SDRAM is turned off). Presumably the
shallow suspend mode is gating some sort of clock that's important but
I couldn't easily figure out how to get it working.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add devicetree support for 96Boards Meerkat96 board from Novtech. This
board is one of the Consumer Edition boards of the 96Boards family based
on i.MX7D SoC. Following are the currently supported features of the
board:
* uSD
* WiFi/BT
* USB
More information about this board can be found in 96Boards product page:
https://www.96boards.org/product/imx7-96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
