Currently, panel jitter and loss of precision are not
compensated when calculating the trigger window size
for a QSYNC panel. These errors can be signigicant on
panels supporting very slow frame rate (10 Hz).
This change improves fixed point calculation and take
into account panel jitter when calculating the minimum
qsync time period.
Change-Id: Ibe620862afbd853580992fccec09cac8307b92bd
Signed-off-by: Amine Najahi <quic_anajahi@quicinc.com>
The encoder modeset updates all the plane's qos_dirty flag attached
to the crtc to make sure the qos params are updated during seamless
mode-switch cases like fps or resolution switch. But this is not
required for cwb encoder modeset as it does not have any effect on
the planes attached to the main display. Add check to avoid this
reprogramming.
Change-Id: I1ab7a71971b7200a50e6643407327734b1c9cbc5
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
The cwb_enc_mask is set by the wb phys encoder during the validate
phase and this is in-turn used during the commit phase. During
seamless transition cases like poms with cwb, the encoders are
disabled and then enabled back after the validate phase. The cwb
flags are reset during this time leading to issues. Cache the flag
and reapply it during the modeset to avoid this case.
Change-Id: I5df1be18a5e30bb1107dc0f2e87d771a735f1ab6
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
In the current code if there is a switch from DSC to non-DSC
mode, all the DSC blocks attached to the sde_encoder are not
cleaned up properly. Due to this, during virt disable these
DSC blocks are disabled and flushed resulting in underruns
on other ctl paths which might be using them. This change
properly cleans up all the dsc/vdc attached to the sde
encoder to avoid such issues.
Change-Id: Ie644701cbda6b4d056bc7ef30300be96096c5214
Signed-off-by: Yashwanth <quic_yvulapu@quicinc.com>
Signed-off-by: Narendra Muppalla <quic_nmuppall@quicinc.com>
Enable the clks/irqs & update RSC state during encoder disable.
This ensures RSC is in correct state during the non-primary disable
commit as it might have entered idle power collapse before the
disable.
Change-Id: Idf82efb3a7bc895e1a97c6cdeeb62970184c8e5d
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Add tx wait for WB display during modeset to avoid unbalanced
IRQ handle.
Change-Id: I18337e2a06fe5ec98d4d6e6d766abbf4ec585703
Signed-off-by: Lei Chen <quic_chenlei@quicinc.com>
In case of dual dsi usecase, since both the encoders use
the same CTL path, this change ensures that uidle ctl
settings are updated only by the master encoder.
Change-Id: Ic47703aeee69999b4535034b5cd7a65cf53cd0fb
Signed-off-by: Yashwanth <quic_yvulapu@quicinc.com>
The sequence during which issue is observed:
1) wb pending_retire_fence_cnt is equal to 2 due to which
it waits for WB_DONE irq. Current pending_retire_fence_cnt
is 2 and required pending_retire_fence_cnt is 1.
2) Due to external reasons, irq's are disabled and after
some duration, back to back irq's are received.
3) Because of this, pending_retire_fence_cnt becomes zero
before the commit thread could wakeup and validate the
condition.
sde_encoder_helper_wait_for_irq API will wait for complete
timeout due to the count mismatch. This change adds
required check to early exit in such usecases.
Change-Id: I4f9c817cc7acee17424b77928d34b039afcaeae5
Signed-off-by: Yashwanth <quic_yvulapu@quicinc.com>
CTL datapath idx can be switched between secondary and external displays
as per current SW code. This change avoids the clearing the SW flush ctx
in prepare_commit during resume use case. It fixes the GPU fence timeouts
seen during below scenario.
Issue scenario:
1. Primary display was using CTL_0 and it is reserved.
2. Secondary display was using CTL_1 and suspend occurred.
CTL_1 is added to RM free list.
3. When external Display is connected, it starts using CTL_1
datapath.
4. Secondary display is resumed and it starts using CTL_2.
During prepare_commit, phys_enc->hw_ctl was CTL_1 and
SW is clearing the flush ctx of external Display.
5. Since CTL_1 flush bits are cleared, SW is not programming the
CTL_FLUSH register for this composition and release/retire fences
are not signaled causing fence timeouts at GPU end and Input fence
timeout at display end finally leading to SF hung.
Change-Id: Ic843ce5c4f06f1620636abd24d443952c2ba8dc5
Signed-off-by: Jayaprakash Madisetty <quic_jmadiset@quicinc.com>
When VSYNC interrupts are delayed due to irq latencies, there is a
possibility that the timeout handler checking the irq status and the
irq handler clearing the status bit happening at the same time on
different CPU cores. This is reported as an error, though there is
not actual issue. Handle this case, by adding an additional ctl-flush
register check in the vsync timeout handler. As part of the change
add error/eventlogs in commit-done wait failures.
Change-Id: Ie7e30dc4ef1e50651cee9015cd3f2caeacf47e5f
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Add support display emulation targets on RUMI
This change does the following:
-parse dt node to enable display emulation mode.
-use sde_reg_read for pool timeout ops and debug fs dump.
-increases the kickoff timeout when emulation is enabled.
-bypass AXI halt operation when emulation is enabled.
Change-Id: Idc493964c0b8fc89f5d85fcc5755e0874a12d211
Signed-off-by: Amine Najahi <quic_anajahi@quicinc.com>
Log the vblank timestamp during vblank callback. This will be
useful in calculating the precise difference between the vsync
while debugging. As part of the change, remove the vblank
counter logging in sde_crtc as it floods the logs with 4 entries
for each vblank request.
Change-Id: I6b532ad657581fb2a34318541acbd81a44858819
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
This change adds support for triggering output
hw fence upon programmable line count.
Change-Id: Ie4b8252e4f9a448a8c11d17696b9bb0ded81b04b
Signed-off-by: Christina Oliveira <quic_coliveir@quicinc.com>
Starting mdss 9.0, dpu supports triggering
the frame fetch through hw-fencing. This change
adds support for this hw-fence feature.
Change-Id: Icc7d0b69fc2a51103d14612f5ac89b44a47ed826
Signed-off-by: Ingrid Gallardo <quic_ingridg@quicinc.com>
Signed-off-by: Christina Oliveira <quic_coliveir@quicinc.com>
This change collects the OPR, MISR values. If the values are
different than the previous then notify to client with custom event.
Change-Id: I2546439be1f665d90e6505d65283d28096bf7cdd
Signed-off-by: Akshay Ashtunkar <quic_akshayaa@quicinc.com>
This change updates vsync source as part of rc post modeset. For some
use cases like idlepc with DFPS, vsync could be configured for
previous fps and can cause timeouts during next frame.
Change-Id: I110fd958d2970eaca50ace0e72c4faea3fc64ce8
Signed-off-by: Narendra Muppalla <quic_nmuppall@quicinc.com>
Add line insertion support for sspp, this is used to support
display with external splitter. Line insertion logic checks
the difference between screen logical height and physical
height. If any difference is observed adds dummy and active
lines on screen.
Change-Id: Ieec322273df000a53fb39e05174c2d67c3c2da81
Signed-off-by: Rajesh kv <quic_kvrajesh@quicinc.com>
Disable the autorefresh during encoder disable to avoid any
pending frame transfers while disabling. Additionally, handle
frame_done for new autorefresh frames to signal the fences and
proper accounting of pending_kickoff counter.
Change-Id: I8af114972b19ccdf0edab6b4c454ee90b4e8d8cf
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
Avoid various possible nullptr dereferences
and check validity of index before accessing
arrays. Addresses issues highlighted by
static analysis.
Change-Id: I5abfbc8c4cacb56e9decc3a6339ab0fa3a63b606
Signed-off-by: Nisarg Bhavsar <quic_bhavsar@quicinc.com>
Currently aggresive idle-pc entry is only enabled in
case of doze-suspend mode. Extend the support to doze
mode as well.
Change-Id: I8e9e0e116bb65a1aec0180bf9bc10bed99d4a137
Signed-off-by: Govinda Rao K S <quic_gkarikur@quicinc.com>
MDSS 9.0.0 added support for logging MDP_VSYNC timestamp. Use it for
video-mode panels and rely on PANEL_VSYNC timestamp for cmd-mode panels
as it relies on external panel TE.
Change-Id: I09b25d893075bee7cb2da98d4c4b4e54eb09bd6e
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
* quic/display-kernel.lnx.5.10:
disp: msm: sde: avoid error during fal10_veto override enablement
disp: msm: update copyright description
disp: msm: sde: configure dest_scaler op_mode for two independent displays
disp: msm: dp: updated copyright set for 4nm target
Revert "disp: msm: sde: consider max of actual and default prefill lines"
disp: msm: sde: Reset backlight scale when HWC is stopped
disp: msm: dp: avoid duplicate read of link status
disp: msm: dsi: update vreg_ctrl settings for cape
disp: msm: fail commit if drm_gem_obj was found attached to a sec CB
disp: msm: dp: updated register values for 4nm target
disp: msm: sde: update framedata event handling
disp: msm: dsi: Add new phy comaptible string for cape
disp: msm: sde: software override for fal10 in cwb enable
disp: msm: update cleanup during bind failure in msm_drm_component_init
disp: msm: sde: dump user input_fence info on spec fence timeout
disp: msm: sde: add null pointer check for encoder current master
disp: msm: dsi: enable DMA start window scheduling for broadcast commands
disp: msm: sde: avoid alignment checks for linear formats
disp: msm: reset thread priority work on every new run
disp: msm: sde: send power on event for cont. splash
disp: msm: sde: always set CTL_x_UIDLE_ACTIVE register to "1"
disp: msm: use vzalloc for large allocations
disp: msm: sde: Add support to limit DSC size to 10k
disp: msm: sde: add tx wait during DMS for sim panel
disp: msm: dsi: add check for any queued DSI CMDs before clock force update
disp: msm: sde: correct pp block allocation during dcwb dither programming
disp: msm: sde: avoid setting of max vblank count
disp: msm: sde: add cached lut flag in sde plane
disp: msm: sde: avoid use after free in msm_lastclose
disp: msm: sde: update TEAR_SYNC_WRCOUNT register before vsync counter
disp: msm: dsi: Support uncompressed rgb101010 format
disp: msm: sde: update idle_pc_enabled flag for all encoders
disp: msm: sde: flush esd work before disabling the encoder
disp: msm: sde: allow qsync update along with modeset
disp: msm: dp: avoid dp sw reset on disconnect path
disp: msm: sde: consider max of actual and default prefill lines
disp: msm: ensure vbif debugbus not in use is disabled
disp: msm: sde: update cached encoder mask if required
disp: msm: sde: while timing engine enabling poll for active region
disp: msm: enable cache flag for dumb buffer
disp: msm: sde: disable ot limit for cwb
disp: msm: sde: avoid race condition at vm release
disp: msm: dsi: set qsync min fps list length to zero
disp: msm: sde: reset mixers in crtc when ctl datapath switches
disp: msm: sde: update vm state atomic check for non-primary usecases
disp: msm: sde: reset CTL_UIDLE_ACTIVE register only if uidle is disabled
Change-Id: If480e7f33743eb4788549f853ba05e744ecb38d3
Signed-off-by: Narendra Muppalla <quic_nmuppall@quicinc.com>
This change avoids sde error during fal10_veto override enablement
for targets with uidle disabled and early returns in such case.
Change-Id: I491952615d7b3cbd70d35b4a90ee8d27ab56c2ad
Signed-off-by: Yojana Juadi <quic_yjuadi@quicinc.com>
This change updates copyright description with correct
license marking as per the guidelines.
Change-Id: Ia74b721e78afcc7f8e88bcbccfcf15430111ec37
Signed-off-by: Yashwanth <quic_yvulapu@quicinc.com>
When cwb is enabled enable software override for fal10 veto to
block fal10 entry as MDSS can keep asserting uidle if there
are no fetch clients like dim layer only usecase.
Change-Id: Ief51499d370c20fcbdda79576aee0179578650fd
Signed-off-by: Prabhanjan Kandula <quic_pkandula@quicinc.com>
Signed-off-by: Nilaan Gunabalachandran <quic_ngunabal@quicinc.com>
Use #if IS_ENABLED() instead of #ifdef for configurations as vendor module
guidelines.
Use #if IS_ENABLED(CONFIG_XXX) instead of #ifdef CONFIG_XXX to ensure that
the code inside the #if block continues to compile if the config changes
to a tristate config in the future.
The differences are as follows:
1.#if IS_ENABLED(CONFIG_XXX) evaluates to true when CONFIG_XXX is set to
module (=m) or built-in (=y).
2.#ifdef CONFIG_XXX evaluates to true when CONFIG_XXX is set to
built-in(=y) , but doesn't when CONFIG_XXX is set to module(=m).
Use this only when you're certain you want to do the same thing
when the config is set to module or is disabled.
Change-Id: Ia806b9b01ad8414d0e4de027a382cb68e7fb4a6a
Signed-off-by: GG Hou <quic_renjhou@quicinc.com>
During virt disable call, sde_enc master was used without checking
for null condition. It results in crash. This change adds required
null pointer check for sde encoder current master before dereferencing
to avoid crash.
Change-Id: I69ee17017712ea3549bfefce5975a564a5a8c2e9
Signed-off-by: Yojana <quic_yjuadi@quicinc.com>
msm/sde/sde_encoder.c
_sde_encoder_update_rsc_client()
sde_encoder_prepare_for_kickoff()
msm/dsi/dsi_drm.c
dsi_bridge_mode_fixup()
Lower the cyclomatic complexity for this function by splitting
the work into helper functions.
Change-Id: I2285809a33078e29989a6b44800c18342aa24170
Signed-off-by: GG Hou <quic_renjhou@quicinc.com>
pm_runtime_get_sync increases the usage_count refcount immaterial of
success/failure of the call, leading to invalid refcount on failures.
Use pm_runtime_resume_and_get instead, which takes care of reducing the
refcount on failure cases before returning from the function.
Change-Id: Ib96050d5d7ecbd717e58b8a0dde2d03312444e15
Signed-off-by: Veera Sundaram Sankaran <quic_veeras@quicinc.com>
This change adds pp_tx during DMS switch for sim panel to
prevent WD timer getting updated in middle of the frame and
creating early vsync which might result in ppdone timeout.
For non-sim panels, this tx wait is not required and is
done similar to posted start.
Change-Id: Ifec68535efa19df27e651ce0a39c03627dff2089
Signed-off-by: Yashwanth <quic_yvulapu@quicinc.com>
At present, idle_pc_enabled flag will be set for encoders
containing only these capabilities MSM_DISPLAY_CAP_CMD_MODE
and MSM_DISPLAY_CAP_VID_MODE. When cwb is triggered,extra
power vote will be taken during kickoff and vote remains
till cwb is disabled. In between, if primary goes into idle
power collapse, vote taken by cwb will not be removed since
idle_pc_enabled flag is not set. This change updates
idle_pc_enabled flag for all encoders based on catalog
property.
Change-Id: If4f147edbd610d0302e4d6c0a3e6b7de2c729db1
Signed-off-by: Yashwanth <quic_yvulapu@quicinc.com>
Keep posted start as default configuration in driver
if SBLUT is supported on target.
Do not allow HAL to override driver's default frame trigger mode.
Change-Id: I46ad5c87abfb05446592b0e497a23a3a3fc62ca7
Signed-off-by: GG Hou <quic_renjhou@quicinc.com>
Flush ESD status work before resetting the encoder state during
virt_disable sequence to avoid stale pointers being used in
the ESD work.
Change-Id: I4bb08a7a7ae33ad6386169667692736e554141c4
Signed-off-by: Kalyan Thota <quic_kalyant@quicinc.com>
