Enable the VI decimator at the end of Rx and VI enable sequence.
Change-Id: I12045c903b29d4cc830dbbfd242d805a629c0efd
Signed-off-by: Vangala, Amarnath <quic_avangala@quicinc.com>
Update ch_msk and audio path for VI feedback path
in lpass_wsa2 macro.
Change-Id: Ibc96fc1ad82e2e996b11af20522f35e47b94d8f0
Signed-off-by: Ganapathiraju Sarath Varma <quic_ganavarm@quicinc.com>
After ADSP is up during SSR, core_hw_vote may fail and audio_hw_vote
may successed in lpass_cdc_runtime_resume which is caused some timing.
When getting slave device_id, as core_hw_vote is 0, it will skip reading
swr registers and return 0 which causes fail to read correct device_id.
Make this change to avoid calling lpass_cdc_runtime_resume when adsp_up
notification doesn't reach lpass_cdc.
Change-Id: I90a97e5c47bb95180a96ba1c60b462f1fa0124b7
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
Signed-off-by: Kunlei Zhang <quic_kunleiz@quicinc.com>
Implement backend for CPS soundwire port in Bolero.
Change-Id: Ibbd38d067e46be1a71723de04a83bc83f0ec2925
Signed-off-by: Vangala, Amarnath <quic_avangala@quicinc.com>
Propagate all changes to lpass-cdc-wsa-macro to
lpass-cdc-wsa2-macro. Leave get_channel_map alone
because it is wsa macro specific.
Change-Id: I46733a759490d488f46eda24b4006a1dec63c7cc
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
update check not to exceed the array index for active_ch_mask and active_ch_cnt
Change-Id: Ic6d72d7469edbd004cd34a709384d527e90cd26f
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Update digital_cdc_rsc_mgr_hw_vote_enable/disable API with device
info for easy debug. Also, add swrm clock enable checks during SSR.
When SSR happens, swrm->hw_core_clk_en and swrm->aud_core_clk_en will
be reset without resetting audio_vote and core_vote clk. This would
cause clk mismatch in audio driver and adsp and device fails suspending
when there's no audio usecase. Make this change to reset audio_vote
and core_vote clk when receiving SWR_DEVICE_SSR_DOWN.
Change-Id: I9875aac9f6faf8b6481457a70f31b005073369e0
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
Decrease idle holdoff time from 60 to 29 samples as per updated
documentation.
Change-Id: Ia8786020d6de8320f057f418e743507030c734c8
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
New requirement to update compander_ctl7 again_delay
field to 7.
Change-Id: I4c5ef15c645cabded50203bf92facbe7c8ff8c5b
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Update from SOC_ENUM to SOC_SINGLE to match rest of driver
implementation. Also remove remaining dev_mode enum references
in wsa884x driver.
Change-Id: I2a477c4fa8c29373ffa1e8e2eb599a0f1c61653d
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Match datatypes of variables in
lpass_cdc_va_macro_enabl_dmic() with
lpass_cdc_dmic_clk_enable() to prevent CFI issues.
Change-Id: Id378476b1aa6231c8542ca754124716af2b1f50b
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
replace all dev(pr)_err/info logs
that could potentially flood kernel logs with
ratelimit functions dev_err_ratelimited and
dev_info_ratelimited
Change-Id: I32dc6002dead1a07622978c4de63d541c01982fd
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
idle detect thr is a fixed value, do not need to change
Add debug statements in idle detect control func
Change-Id: I68a049f8560a1a444c019df2dc09f7cf62b37d46
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
the offset between LPASS_CDC_WSA_RX_INP_MUX_RX_INT0_CFG1 and
LPASS_CDC_WSA_RX_INP_MUX_RX_INT1_CFG1 is 8 so updating
0x104 + 8* interp
update ng block register write for NG2 mode in Kundu
Change-Id: I44da894feebb5d25bd467ffd4d54adde111778e6
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Use LEGACY source if any of the below use cases is met:
EAR, PBR OFF, IDLE, NG2 and PA GAIN <= 13.5dB
Use PRE-LA when: All other cases
Change-Id: Iace0c1f6fea367a73cd604b958bd5c8905d29509
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Cast returned u16 value to int in VA/TX macro: clk_div_get
to avoid possible data type warnings seen in function
caller.
Change-Id: I08943a26294ce54a207b739867292c01d090623e
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Can now set these registers during init once these values are
acquired.
Method called again before playback in case there are
speaker/recv changes.
Change-Id: I1b544633a660e98acadf94b9589b7656edebdd56
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Update mode argument type from int to u32 to avoid
any potential data loss since input is also u32 type.
Change-Id: I9541a7da20d2a22a0066622736268adffde5adbf
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Add new lpass RX paths. Needed to fix
WSA ADIE Loopback.
Update DAPM enum length to include these RXs.
Change-Id: Ie174cfab20b8beb103eefa94636e76ad756c7345
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Found potential issues relating to uninitialized or out-of-bounds variables
present in codec drivers. Place checks to ensure proper ranges are used.
Change-Id: Ib68cba2413788a57237f1f18fc5ce5fb5c6bfb0a
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Update function to correctly read array from device tree.
Previously not reading values and returning -EINVAL.
WSA bat_cfg/rload/sys_gain are now correctly configured.
Also add softclip clock enable during pbr config.
Change-Id: Ia1b93acfde3e799b3b72e05966d0fa955c3f49ac
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Add idle detect source select based on NG mode,
if NG2 then source is PRE-LA else LEGACY
Change-Id: I4e0cb3825960e6b795038fb5e85cfaa7a2fbfe62
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Add idle detect enable for mixed control path,
and update copyright markings
Change-Id: Idf2932cd1813082f60ee96010788cdb1ef36afbf
Signed-off-by: Shazmaan Ali <quic_shazmaan@quicinc.com>
Lpass-side enablement of new WSA feature.
Configure PBR registers based on WSA bat_cfg/rload/sys_gain.
Some registers updated during init, others during enable_interpolator.
Change-Id: Iac42672182827a9da47700319c61b9d0a17d0936
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Update WSA rload, system gain, bat_cfg to get from wsa_macro device tree.
WSA Bat_cfg change to read from VPHX_SYS_EN_STATUS reg.
Add device tree parsing for these params in WSA macro
and WSA driver.
Remove machine driver method of sending the parameters.
Add default_dev_mode (spkr vs rcv) from device tree for WSA.
Move code from spkr event to userspace controls or probe.
Change system_gain and affected params when switching between
dev_modes.
These changes simplify configuration data and code and allow
more registers to be written during bootup or before playback.
Change-Id: I79966c704adfac1bf2d85aa6519ea574764c7a8b
Signed-off-by: Matthew Rice <quic_mrice@quicinc.com>
Udpate MSM DMIC power up sequence to reduce pop.
Change-Id: I5f3f2e439e31877d3f21c05575c95942b937252e
Signed-off-by: Meng Wang <quic_mengw@quicinc.com>
add kalama config file to all drivers' Kbuild, including soc/dsp/ipc
Change-Id: I56a6092da515f211a56617f0cff60079dbf0aa39
Signed-off-by: Junkai Cai <junkai@quicinc.com>
Sometimes after SSR/DPR is triggered, RX_TX_CORE_CLK, WSA_TX_CORE_CLK
and WSA2_TX_CORE_CLK are not reset which causes WSA or WCD not
detected. Make this change to add reset during SSR.
Change-Id: I343f2f92244de3eee844e220a6201b389dc647b4
Signed-off-by: Meng Wang <mengw@codeaurora.org>
