Some legacy Helium firmware doesn't support SAE roaming, but btm cap is set
in associate request of DUT, then connected SAE AP thinks DUT supports btm,
AP will send btm request to DUT, DUT triggers roaming, but fails and
disconnects from current AP, users will complain this unexpected
disconnect.
Change-Id: Ife9860addef6898a518618f555158e7888ac74db
CRs-Fixed: 2884694
cfg80211_get_chandef_type supports till NL80211_CHAN_WIDTH_40. Any
chan width more than NL80211_CHAN_WIDTH_40 can be treated as
NL80211_CHAN_HT40PLUS. __wlan_hdd_cfg80211_start_ap has the same
logic in-place.
Change-Id: I70166faf16730128039e4e48d9e90aefb1674977
CRs-Fixed: 2717615
When updating the country to be the same value, the function will return
failure. This causes a crash in the wifi start up. Add check to see if
the country code is the same to avoid calling the API.
Change-Id: I7be11857fd9cc87b65f6c598d842a9ed5c024f59
CRs-fixed: 2896855
Currently, In twt setup command, driver set the
TWT command_in_progress before adding the dialog_id
in TWT context. Due to which, set active command
fails because the dialog id was not added to the
twt context. So the add dialog command response is
getting dropped at sme.
Set the TWT command_in_progress after adding the
dialog_id to TWT context.
Change-Id: Ic2c7e23720e2bc9f5a6737ba2f1dc4b1356dc179
CRs-Fixed: 2897736
Currently, P2P mode is not supported in 6GHz mode
Add P2P mode in policy_mgr_is_6ghz_conc_mode_supported
API to support P2P mode in 6GHz mode as fix this.
Change-Id: I2e160641c1784dbbd592b237da6b38929f33abbe
CRs-Fixed: 2896291
WFA VHT 5.2.1 requires to construct SGI80 in the association request
NOT based on AP capabilities in the beacon and probe response frames.
So, construct VHT compatibility SGI 80M and 160M irrespective of peer.
Change-Id: I3a5ed6af1ea6be20c332cd91f48eee015a0c898c
CRs-Fixed: 2888822
If DFS master capability disabled, STA+SAP SCC on DFS is not allowed,
so reset g_sta_sap_scc_on_dfs_chan to 0.
Change-Id: I90b0ec6947f5bc24c9854062f443de0d1f6dc452
CRs-Fixed: 2897719
When processing the TPE IE from, the function has to calculate the
frequencies for each tx power it receives. The calculation is incorrect
which results in a bad lookup when populating the EIRP power value.
This can cause low throughtput issues.
Change-Id: Id854f678bd3933ab1a7198b346ed14d76d964360
CRs-fixed: 2896985
This is to enable feature for detection CE tasklet
scheduling delay and credit response delay issue.
Change-Id: I659aa23eabaa28bfb11051bf15e0343c94061b86
CRs-Fixed: 2874867
Debug change to crash if there is a mismatch in number of
connections and disconnections
Change-Id: I1bb9cac331c0cb491a0ba761a78969537185e414
CRs-Fixed: 2870628
HT is not supported with TKIP/WEP as encryption, WEP 40/104
are WEP, need to be taken into consideration.
Change-Id: Ibce4bf929ce43b8246c14d4cbddfa93c9c25c6cb
CRs-Fixed: 2892721
Add big data stats as part of QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO
vendor command reply, if current state is disconnected.
Change-Id: I84dc1f9901be17ea7b2bd6aecc7bec4c19e77202
CRs-Fixed: 2876395
Currently peer create response support is added for connect path
but in LFR-2.0 case also peer create response received is
processed and lim_post_join_set_link_state_callback() is called
leading to sending vdev start again.
Call the API to fill peer create wma request only for initial
connection.
Change-Id: I24140efd5541f7ed4aa3cef9efebf5a729846902
CRs-Fixed: 2856636
Currently multiple ini is available for setting the broadcast
TWT requestor and responder configuration.
Deprecate "bcast_twt" legacy ini and also don't consider
legacy service capability WMI_SERVICE_BROADCAST_TWT.
So below is the service capability values combination
advertised by firmware:
new fw:
bcast_req bcast_resp legacy
0 0 0 -> disable bcast
0 1 0
1 0 0
1 1 1
old fw:
0 0 1 -> enable TWT
Also change the default value of "twt_bcast_req_resp_config" ini
to 1.
Change-Id: Ic9af296b0efffc8f76f647b5830183867e0adf57
CRs-Fixed: 2873360
Any update to the SRNG TP/HP when the device is in low power
state would result in system errors. While in D3 WoW mode,
disable EXT grp irqs and drain TXRX before sending enter
power save mode to the FW. This will ensure that no interrupts
are received while in WoW mode and as a result there wont be any
HP/TP updates.
Change-Id: Ic1fb7fdd45096b458abf5d243fa652c3da878dc0
CRs-Fixed: 2890568
Add support to configure the HE ER SU for management frame tx
and configuration support to use RU 242 tone for data Tx.
Change-Id: I068c1e7b6808d430d5468bab7ee04e24d5461afd
CRs-Fixed: 2816797
When "wmi_service_configure_roam_trigger_param_support" service
bit is set populate roam score delta and min rssi parameters
and send via WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID.
Change-Id: I3c7fc56a95c28c43992763be3351d91d9fd44041
CRs-Fixed: 2890148
Currently, host sends mantissa in us for
QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA attribute.
Add changes to send wake interval mantissa in TU to firmware
and expectation from usersapce is to set the 1024 in the
exponent to derive the correct wake interval.
Change-Id: I53520369492961207496970fe78189bec6f75ad7
CRs-Fixed: 2897500
Incase peer sends multiple Association
Request or multiple Association Request,
there can be crash due to excessive
logging.
So, rate limit the logging.
Also, this is also valid in case peer
sends multiple Disassociation or
Deauthentication request.
Change-Id: Iec4f70e8154ca0001f6d752f65449bb1d7bce5da
CRs-Fixed: 2891926
Currently pld_ipci_smmu_unmap suppot has been added for IPCI,
PCIE_FW_SIM and SNOC_FW_SIM type cases as an error, moving this
unmap support only for type IPCI.
Change-Id: Ib9a60656920d1cc46e28dc269983b7da8dba7d42
CRs-Fixed: 2896804
Add vendor command interface/feature through which the user
or vendor can set the dtim count as per their requirement.
Change-Id: I26010948c4ed7e3c49bfe0453119235d4f438c6f
CRs-Fixed: 2894349
While parsing the nudge command, the peer mac address is not copied to
the params structure passed to sme. So while Nudge active command,
since peer mac address is NULL, the driver is not able to get the
peer object and set the Nudge active command fails.
Copy the peer mac address to set the active command to peer
object, so that when nudge command response is received, the
response is not dropped due to active command is not nudge.
Change-Id: I11b11b3187dff5a79d0f79106c21d60d04edc17b
CRs-Fixed: 2888903
CNE queries stats via the ext stats vendor cmd. As
part of this, REO commands are enqueued to HW for
each tid to get mpdu_rx and mpdu_rx_missed counts.
In the scenario where the first ext stats request
post STA disconnection and re-connection times out,
the counts from the previous connection are reused.
The second ext stats request can successfully get
the new counts from HW in which case, there is a
possiblity for the mpdu_rx count sent in the second
stats response to be lower than the count sent in
the first stats response.
Fix is to reset the mpdu_rx and mpdu_rx_missed count
on STA connection.
Change-Id: I381f9b6b27d8d023b1932b7d8587df240c1ff4d0
CRs-Fixed: 2896791
