Enable the 4th Tx. completion ring to save CPU load
Initialization and interrupt handling for 4th completion ring
is done here.
Change-Id: I2db27218a3c3e14d719d012f03454a6a7aa647fe
In WBM error processing read peer_id from peer_meta_data
instead of sw_peer_id.
This changes is needed because we need to process Rx packet
on ML peer. But in MLO case sw_peer_id field contains
link_peer_id where as peer_meta_data has ml_peer_id.
Change-Id: I3f469adfdf7efa88cb081e94fa9fe0c54c1fb078
In order to support flow overide feature,
AST table has to be split between RxPCU and DDR.
With this split, RX monitor cannot make use of
ast_index to fetch peer as it is not from DDR.
So make use of sw_peer_id to fetch peer.
This sw_peer_id is derived from RX_MPDU_STAT_START_TLV
Change-Id: Ib2a003a2640fded3287c318d2ad59fd3127af9b6
CRs-fixed: 3004363
HAL generic APIs which use HW definitons that
do not have same value across all lithium chipset
are moved to header files. So that these will be
compiled with appropriate header files
Change-Id: I6c167afa4212c5e884f5e18ff1ccb3bbbba8f5f5
Currently the hardware srng register offset is statically
assigned to the handle. This can lead to incorrect index access
when targets (eg: wcn7850) is added which require additional
register offsets to be stored in the hw srng register offset table.
Move to the index based assignment of the srng register offset.
Change-Id: I8e38bdd0c28068029a0267fce706edf4378b9df8
CRs-Fixed: 2965081
Assign th HAL TX/RX ops in a function instead of assining a structure
directly. This can be later extended to have default ops for a family of
chips and then override that with chip specific ops.
This also helps the case where a new hal_soc->ops needs to be added.
The new 'op' will need to be added to only a default ops initializer
(with assumption that it applies to all chips).
Change-Id: Iefa23d14110fa5252444fad89737a3b2b2fbab6f
CRs-Fixed: 2891049
Currently the FW configures the mac with appropriate
offsets for rx pkt tlvs using the structure defined in
te FW and the host does not send the ring selction config
HTT message. This can create a problem when FW stops subscribing
to tlvs or changes its rx pkt tlvs offset.
Fix this by configuring the rx pkt tlv offsets via HTT
ring selection config message.
Change-Id: I1a2865f91b34dd7bda1af8651d7831097dac0bee
CRs-Fixed: 2860504
Change hal_hw_txrx_ops struct to designated initializer syntax for
structs for 8074v2.
Change-Id: I06f7aad41446623bd8f28cb4de84bfb4fc1bad24
CRs-Fixed: 2837917
Change the alternate indication_0 to WBM instead of
REO2TCL. This is done such that, WBM takes care of
the of the de-linking of the link descriptors and
release the buffers to the respective WBM rings.
WBM should take care of the NULL entries if present
in link descriptor as WBM internal errors.
Change-Id: Ie084e54861bb4611a45cd724bb32d211c62f4f21
If frames from the same FISA flow goes into different REO2SW rings, it
will result in an unexpected FISA behavior. This can happen if the
frames have been reinjected from FW offload module since FW will select
REO2SW1 ring. If the same flow frames hash to other REO2SW rings, then
the same flow UDP frames will do to different rings.
Reo_destination_indication of 6 indicates if the frame has been
reinjected from FW. If so, then continue to deliver the packet without
FISA.
Change-Id: I14a17a10d04909adfb30557d58beb1610e59bf70
CRs-Fixed: 2790292
Adding support for enabling ini config to remap reo destination rings
for HK v1, HK v2, maple and pine platforms.
Change-Id: Id9d304521f32497e3acd845ddd2973b96b641516
Size of the TLVs have changed across generation of chipsets
Offset values need to be configured into DMA register for preheader DMA
Added APIs to get offsets of each TLV based on chip type
Change-Id: Ic011332cbf3a1017f324f246e47c9e2c91441c70
Support RX 2K jump/OOR frame handling from REO2TCL ring.
(a) configure REO error destination ring register to route 2K jump
/OOR frame to REO2TCL ring.
(b) for 2K jump RX frame, only accept ARP frame and drop others,
meanwhile, send delba action frame to remote peer once receive first
2K jump data.
(c) for OOR RX frame, accept ARP/EAPOL/DHCP/IPV6_DHCP frame, otherwise
drop it.
Change-Id: I7cb33279a8ba543686da4eba547e40f86813e057
CRs-Fixed: 2631949
Add HAL layer changes for full monitor mode.
Define HAL API and Data structures to read sw_monitor_ring
descriptor.
CRs-Fixed: 2630982
Change-Id: I015fa106d9da74222bef092d50e96fc70a117a4a
Write TID-no correctly for DSCP-value if
2 consecutive registers are needed to configure
the mapping.
Change-Id: I857f95e2d1bda0214a32b2802f1dcc460be87085
For qcn9000, As part HW enhancements, PPDU_ID is sent
in reo_entrance_ring descriptor instead of RX_MPDU_START
tlv. Add support to read ppdu id from descriptor.
Modify existing hal API hal_rx_hw_desc_get_ppduid_get ()
arguments to pass RxDMA ring HW descriptor.
Usage:
a. Use hal_rx_hw_desc_get_ppduid_get () -
to get ppdu id from rx_tlv_hdr or hw descriptor based on target.
for qcn9000, this API gets ppdu_id from HW descriptor,
for other platforms, gets ppdu_id from rx_tv_hdr
b. Use hal_rx_get_ppdu_id () - to get ppdu_id from rx_tlv_hdr
Change-Id: I5838227c12cde50cbb2a9da7a0d8056b8b9b7ef5
Rather than extracting msdu end pkt tlv information per field basis
during fast data path, extract msdu end pkt tlv information at once
and store in local structure.
Change-Id: I0877ba4f824d480cc0851c72090f010852d0d203
fix the issue for block ack/ack for tx capture mode.
1. Hanndle BAR frame.
2. set rate for ACK frame.
3. Check block ack session and use block ack if block
ack session is established.
4. no ACK for broadcast probe request.
5. not ack if the ack policy is set to no ack in qos control.
Change-Id: I4f22c1c976334978fb971b42319fb3a6e43a00c2
the current HAL API is to read the WBM internal error
bit from the wbm release ring descriptor is always taking
HKv1 HW structure. But the wbm_internal_error bit
placement has changed from HKv2, for this reason we have
to use target specific HAL API.
Change-Id: I44789180754ca21ae59650b6d8620321a1f12569
Channel Frequency Response(CFR) feature requires PPDU information
for correlation with CFR data. Host subscribes for the relevant PPDU
status TLVs via the Host RX monitor status ring. During monitor status
ring reap, all information needed for CFR correlation is accumulated
in a HAL PPDU structure and delivered to WDI event subscribers.
Change-Id: I3662b60375cb8886447a2fba3efead6a1ef3a98d
CRs-Fixed: 2593408
sw_frame_group_id decides process for frame. USER_STATS tlv case uses
sw_frame_group_id to add qos_null frame control to rx_status.
Change-Id: Ia3da8dbe4fc4c2d0f21fa8864e6b4e87170ba8f6
Write into hal register using three floating windows instead of one.
This change is done to avoid frequent window changes for writing into
DP and CE registers. Instead 3 windows are used. One window is statically
mapped to CE block and another window is mapped statically to DP block.
Due to this design there is no need to change the window register to
write into these blocks and write can be done on corresponding window
with single iowrite32. Similar loginc is used for ioread32.
Also modified the hp_addr and tp_addr in initialisation stage so that
hal_write will not have multiple if checks.
Change-Id: Ibb99ec4da7f63323082e46a28afbe90e1f555545
CRs-fixed: 2507441
Add hal_rx_get_rx_sequence API to retrieve
rx sequence value based on the chipset.
Change-Id: I8377b96dfe04e9695a183482d9fcc4a804f845e0
CRs-Fixed: 2522133
Implement hal_rx_tlv_get_tcp_chksum API
to retrieve tcp_udp_checksum value
based on the chipset.
Change-Id: Ifab970f10af06f8c0cdbd14d57cb66b49bae1648
CRs-Fixed: 2522133
Implement hal_rx_msdu_get_flow_params API
per chipset as the macro
to retrieve the flow parameters is
chipset dependent.
Change-Id: I6ef83232ebdf7497871a7fc588e082d14cdc9e75
CRs-Fixed: 2522133
Implement hal_rx_msdu_cce_metadata API per
chipset as the macro to retrieve the cce_metadata
value is chipset dependent.
Change-Id: Icd87d4ac32be78d69b24da106381a7669c86ada6
CRs-Fixed: 2522133
Implement hal_rx_msdu_fse_metadata API per
chipset as the macro to retrieve the fse_metadata
value is chipset dependent.
Change-Id: Iae7f532460b5203af2f95c504a6941c0b18b665e
CRs-Fixed: 2522133
Implement hal_rx_msdu_flow_idx_timeout API
per chipset as the macro
to retrieve the flow_idx_timeout value is
chipset dependent.
Change-Id: I03030e3763b3c4a9099699a2d24b8110961610cf
CRs-Fixed: 2522133
Implement hal_rx_msdu_flow_idx_invalid API
per chipset as the macro
to retrieve the flow_idx_invalid value is
chipset dependent.
Change-Id: I5b8622eb896456b7388016a16657048d0da4e970
CRs-Fixed: 2522133
Implement hal_rx_msdu_flow_idx_get API
per chipset as the macro
to retrieve the flow_idx value is
chipset dependent.
Change-Id: I75131d7c048f5b67489ed25fbd52bfcf01bab782
CRs-Fixed: 2522133
Add the following macros:
1. HAL_REO_CONFIG
2. HAL_RX_MSDU_DESC_INFO_GET
3. HAL_RX_LINK_DESC_MSDU0_PTR
Add the relevant function pointers to
retrieve the descriptor info from the
above mentioned macros based on a
given chipset.
Change-Id: If44ae3d91397f1b1b0c36a49ce56a2c5e719434e
CRs-Fixed: 2522133
Add the following macros:
1. HAL_RX_GET_FC_VALID
2. HAL_RX_GET_TO_DS_FLAG
3. HAL_RX_GET_MAC_ADDR2_VALID
4. HAL_RX_GET_FILTER_CATEGORY
5. HAL_RX_GET_PPDU_ID
Also add function pointers to
retrieve the flags from the above
macros.
Change-Id: I334b198588ceba77cd30bdde7ebc500cdbe18358
CRs-Fixed: 2522133
Add the following HAL macros:
1. HAL_RX_MSDU0_BUFFER_ADDR_LSB
2. HAL_RX_MSDU_DESC_INFO_PTR_GET
3. HAL_ENT_MPDU_DESC_INFO
4. HAL_DST_MPDU_DESC_INFO
Add relevant function pointers to retrieve
descriptor info from the macros based
on chipsets.
Change-Id: I99ce7566a668180c7849eedea915b6f23a8dbf35
CRs-Fixed: 2522133
Implement hal_tx_desc_set_mesh_en API
based on the chipset as
the macro to set mesh_en value is
chipset dependent.
Change-Id: I43c85e4ed6fd4f9992de5b71857cdb8becd1dd36
CRs-Fixed: 2522133
Implement hal_rx_msdu_end_sa_sw_peer_id API
based on the chipset as
the macro to retrieve sa_sw_peer_id value is
chipset dependent.
Change-Id: I2efd1f851539bbffc8f75c7662045c1f4a3c4469
CRs-Fixed: 2522133
Implement hal_rx_mpdu_start_mpdu_qos_control_valid
API based on the chipset as
the macro to retrieve mpdu_qos_control value is
chipset dependent.
Change-Id: I61449ff5afc958f1a1f93013b0c5ab56d38cc833
CRs-Fixed: 2522133
Implement hal_reo_status_get_header_generic
based on the chipset as the macro to retrieve
reo_status value is chipset dependent.
Change-Id: I43bd624bec37fb051f33b4828fcf7cd3e4b2a61e
CRs-Fixed: 2522133
Implement hal_rx_hw_desc_get_ppduid API based
on the chipset as the macro to retrieve
ppduid value is chipset dependent.
Change-Id: I7d3457d731ea486f04367f98f9f18d3f1c0fcfd7
CRs-Fixed: 2522133
Implement hal_rx_tid_get API based on
the chipset as the macro to retrieve
tid value is chipset dependent.
Change-Id: I37eab3f3c1c2bbba6094b9ddb24d72712b819f73
CRs-Fixed: 2522133
