Update change for audio playback and record to work
on bengal target with wcd937x codec.
Change-Id: I2f781e2132b018995f30f4192efd08732196cd28
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Update PCM ID with correct values in comments.
Change-Id: Ie456481aa57f0adebb20921d8d0f0d25c7b714e0
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
After master init sets COMP_CFG, wait for soundwire link
status to be connected for SWR version 1.6. Update wait
for soundwire link disconnect for all masters.
Change-Id: I0c0b34f225f88f1b3838b0aa653b57b2c7c0cc40
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
During SSR, sometimes swr get logical addr fails.
Add sufficient delay after reset and retry logic
for get logical addr.
Change-Id: I2a932e99896e0055f3b35f9b251008612f43b79f
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
On receive of change enum slave status interrupt, update
slave host_irq bit for all attached slave dev_nums.
Change-Id: Idaad7a73a7ba9ab271f3fb6974f8d09df3f957b8
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Add support to handle wsa883x codec interrupts and runtime
detection of wsa883x variant.
Change-Id: I06fc113a390c04e890062761cff8ae7436acb662
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Mask bus clash interrupt before clock stop mode to avoid
misfire of the interrupt. Clear and enable the interrupt
after clock is enabled.
Change-Id: I494073a668d298eef466c0f10ab202c3c69f9968
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Enable IRQ for wakeup is called multiple times resulting in
throttling. This is because irq is not disabled after enablement.
Disable wakeup irq in runtime resume to fix the issue. Also
add check so that irq is not disabled more than once.
Change-Id: Ib5b7493298beb3ca4bcf78b2adbd7d4ac9ce6111
Signed-off-by: Vatsal Bucha <vbucha@codeaurora.org>
Check comp status based on active and inactive request
and return once status met.
Change-Id: I75669558875d8ab6fc23a02c888e6083e15aee08
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Update rx droop based on sampling rate to avoid change in
gains between different sampling rates.
Change-Id: Icb2b0bc51a61395c2ee96f63c29555614fe9e505
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Add path for routing in call uplink and downlink to
MultiMedia9.
Change-Id: Id43519ca3cd31aafc0f88a1c2428b3ddc7cc1f93
Signed-off-by: Zhou Song <zhous@codeaurora.org>
In soundwire version 1.6 as AHB HCLK and MCLK
are decoupled, need to wait for clock stop
entry and exit scenarios to execute before
any further transactions. Keep monitor on
COMP status accordingly.
Change-Id: I03204526d7dd634a79193b55c6744edca8664d93
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
MFC set param failed in DSP due to payload mismatch
and stereo echo reference doesn't work.
Channel type parameter in MFC config payload is an
array of uint16_t, but it is assumed as an array
of uint8_t while copying from device structure.
Fix this by copying the channel type one by one
instead of using memcpy.
CRs-Fixed: 2197468
Change-Id: I4b6959e8db56743ac98da75ddc3aa8f56964b4ca
Signed-off-by: Aditya Bavanari <abavanar@codeaurora.org>
