Ensure SDE_ERROR error log print function name and line number.
Add a macro DISP_DEV_ERR as a wrapper of dev_err to ensure origin dev_err
will print function name and line number.
This would help with analysis of errors reported with automated testing.
Expected display error log format:
[FUNCTION_NAME:line] ERROR_MESSAGE
Change-Id: I354f45b492059d5ba2bb110d56443fd338add7ad
Signed-off-by: GG Hou <quic_renjhou@quicinc.com>
* quic/display-kernel.lnx.5.10:
disp: msm: sde: avoid error during fal10_veto override enablement
disp: msm: update copyright description
disp: msm: sde: configure dest_scaler op_mode for two independent displays
disp: msm: dp: updated copyright set for 4nm target
Revert "disp: msm: sde: consider max of actual and default prefill lines"
disp: msm: sde: Reset backlight scale when HWC is stopped
disp: msm: dp: avoid duplicate read of link status
disp: msm: dsi: update vreg_ctrl settings for cape
disp: msm: fail commit if drm_gem_obj was found attached to a sec CB
disp: msm: dp: updated register values for 4nm target
disp: msm: sde: update framedata event handling
disp: msm: dsi: Add new phy comaptible string for cape
disp: msm: sde: software override for fal10 in cwb enable
disp: msm: update cleanup during bind failure in msm_drm_component_init
disp: msm: sde: dump user input_fence info on spec fence timeout
disp: msm: sde: add null pointer check for encoder current master
disp: msm: dsi: enable DMA start window scheduling for broadcast commands
disp: msm: sde: avoid alignment checks for linear formats
disp: msm: reset thread priority work on every new run
disp: msm: sde: send power on event for cont. splash
disp: msm: sde: always set CTL_x_UIDLE_ACTIVE register to "1"
disp: msm: use vzalloc for large allocations
disp: msm: sde: Add support to limit DSC size to 10k
disp: msm: sde: add tx wait during DMS for sim panel
disp: msm: dsi: add check for any queued DSI CMDs before clock force update
disp: msm: sde: correct pp block allocation during dcwb dither programming
disp: msm: sde: avoid setting of max vblank count
disp: msm: sde: add cached lut flag in sde plane
disp: msm: sde: avoid use after free in msm_lastclose
disp: msm: sde: update TEAR_SYNC_WRCOUNT register before vsync counter
disp: msm: dsi: Support uncompressed rgb101010 format
disp: msm: sde: update idle_pc_enabled flag for all encoders
disp: msm: sde: flush esd work before disabling the encoder
disp: msm: sde: allow qsync update along with modeset
disp: msm: dp: avoid dp sw reset on disconnect path
disp: msm: sde: consider max of actual and default prefill lines
disp: msm: ensure vbif debugbus not in use is disabled
disp: msm: sde: update cached encoder mask if required
disp: msm: sde: while timing engine enabling poll for active region
disp: msm: enable cache flag for dumb buffer
disp: msm: sde: disable ot limit for cwb
disp: msm: sde: avoid race condition at vm release
disp: msm: dsi: set qsync min fps list length to zero
disp: msm: sde: reset mixers in crtc when ctl datapath switches
disp: msm: sde: update vm state atomic check for non-primary usecases
disp: msm: sde: reset CTL_UIDLE_ACTIVE register only if uidle is disabled
Change-Id: If480e7f33743eb4788549f853ba05e744ecb38d3
Signed-off-by: Narendra Muppalla <quic_nmuppall@quicinc.com>
When cwb is enabled enable software override for fal10 veto to
block fal10 entry as MDSS can keep asserting uidle if there
are no fetch clients like dim layer only usecase.
Change-Id: Ief51499d370c20fcbdda79576aee0179578650fd
Signed-off-by: Prabhanjan Kandula <quic_pkandula@quicinc.com>
Signed-off-by: Nilaan Gunabalachandran <quic_ngunabal@quicinc.com>
As per HW recommendation, FAL10_VETO_OVERRIDE register can
be programmed to disable FAL10 in alternate to disabling
uidle at the sspp level as disabling UIDLE controller will
only disable DPU traffic shaping and will not stop the
system from entering FAL10 state. This change programs
FAL10_VETO_OVERRIDE register during uidle disable and also
sets CTL_x_UIDLE_ACTIVE register to always one to avoid
race condition between different CTL paths.
Change-Id: I9c55f5da2037cb8c448cc978eac0a04608a93650
Signed-off-by: Yashwanth <quic_yvulapu@quicinc.com>
Align the HW catalog to use common naming amongst the "revision"
and "version" structure members.
Change-Id: Ib6c81aee6cb49208b0699db4a75b4eb9dc79e800
Signed-off-by: Steve Cohen <quic_cohens@quicinc.com>
Add support for the option to enable microidle FAL1 only setting.
Previously microidle enabled would automatically have both
FAL1 and FAL10. Now in cases of higher FPS or DFPS we can
choose to enable FAL1. This change also adds qos recommended
waipio target specific fps limits for fal1 and fal10.
Change-Id: I7aa7d003afc3ac77c671b2467b0e6dedaae772aa
Signed-off-by: Samantha Tran <samtran@codeaurora.org>
Signed-off-by: Prabhanjan Kandula <pkandula@codeaurora.org>
This change adds the hooks to enable the active signal override
in power collapse sequence. Active signal override is needed to
disable the clock gating when the power collapse sequence
is running.
Change-Id: I9edaed7960b236b3d0179cb67f9cc2c9b3546c9d
Signed-off-by: Abhijit Kulkarni <kabhijit@codeaurora.org>
Print uidle status fal10 enable bit as part of checking status.
Change-Id: Ibe00216ac22bb31fbe0925db3abc1d5dc4371ad3
Signed-off-by: Nilaan Gunabalachandran <ngunabal@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
