Avoid shutting down DSI PHY and lanes before entering into
idle collapse.
Change-Id: I62fb40c2398e544b08b8cb8788ac2dc1143a82ce
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
* quic/display-kernel.lnx.5.10:
disp: msm: sde: avoid error during fal10_veto override enablement
disp: msm: update copyright description
disp: msm: sde: configure dest_scaler op_mode for two independent displays
disp: msm: dp: updated copyright set for 4nm target
Revert "disp: msm: sde: consider max of actual and default prefill lines"
disp: msm: sde: Reset backlight scale when HWC is stopped
disp: msm: dp: avoid duplicate read of link status
disp: msm: dsi: update vreg_ctrl settings for cape
disp: msm: fail commit if drm_gem_obj was found attached to a sec CB
disp: msm: dp: updated register values for 4nm target
disp: msm: sde: update framedata event handling
disp: msm: dsi: Add new phy comaptible string for cape
disp: msm: sde: software override for fal10 in cwb enable
disp: msm: update cleanup during bind failure in msm_drm_component_init
disp: msm: sde: dump user input_fence info on spec fence timeout
disp: msm: sde: add null pointer check for encoder current master
disp: msm: dsi: enable DMA start window scheduling for broadcast commands
disp: msm: sde: avoid alignment checks for linear formats
disp: msm: reset thread priority work on every new run
disp: msm: sde: send power on event for cont. splash
disp: msm: sde: always set CTL_x_UIDLE_ACTIVE register to "1"
disp: msm: use vzalloc for large allocations
disp: msm: sde: Add support to limit DSC size to 10k
disp: msm: sde: add tx wait during DMS for sim panel
disp: msm: dsi: add check for any queued DSI CMDs before clock force update
disp: msm: sde: correct pp block allocation during dcwb dither programming
disp: msm: sde: avoid setting of max vblank count
disp: msm: sde: add cached lut flag in sde plane
disp: msm: sde: avoid use after free in msm_lastclose
disp: msm: sde: update TEAR_SYNC_WRCOUNT register before vsync counter
disp: msm: dsi: Support uncompressed rgb101010 format
disp: msm: sde: update idle_pc_enabled flag for all encoders
disp: msm: sde: flush esd work before disabling the encoder
disp: msm: sde: allow qsync update along with modeset
disp: msm: dp: avoid dp sw reset on disconnect path
disp: msm: sde: consider max of actual and default prefill lines
disp: msm: ensure vbif debugbus not in use is disabled
disp: msm: sde: update cached encoder mask if required
disp: msm: sde: while timing engine enabling poll for active region
disp: msm: enable cache flag for dumb buffer
disp: msm: sde: disable ot limit for cwb
disp: msm: sde: avoid race condition at vm release
disp: msm: dsi: set qsync min fps list length to zero
disp: msm: sde: reset mixers in crtc when ctl datapath switches
disp: msm: sde: update vm state atomic check for non-primary usecases
disp: msm: sde: reset CTL_UIDLE_ACTIVE register only if uidle is disabled
Change-Id: If480e7f33743eb4788549f853ba05e744ecb38d3
Signed-off-by: Narendra Muppalla <quic_nmuppall@quicinc.com>
This change updates copyright description with correct
license marking as per the guidelines.
Change-Id: Ia74b721e78afcc7f8e88bcbccfcf15430111ec37
Signed-off-by: Yashwanth <quic_yvulapu@quicinc.com>
Cape uses phy version 4.3 but requires programming of
different values for vreg_ctrl_0 and vreg_ctrl_1 to
configure LDO setting. Add new phy compatible string
to distinguish cape from other chipsets and program
the registers accordingly.
Change-Id: I68b266cc6e179d211ee0fd05584a605f39b4d31d
Signed-off-by: Srihitha Tangudu <quic_tangudu@quicinc.com>
Change adds the new files for DSI PHY version 5 and 4nm
DSI PLL.
Change-Id: I97712d6ce53a60a6fae1c8331b6ba9a5d17b8d34
Signed-off-by: Shashank Babu Chinta Venkata <quic_schintav@quicinc.com>
Add dsi ctrl version 2.7 and dsi phy version 5.2 support for
Kalama hardware.
Change-Id: Ia7b4c8a2e1579458f114e466de8b24855e9251ce
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Cleanup DSI HW register access layer to minimize the number of macros that
access readl/writel functions.
Change-Id: Id78025b3837f9126f64681b4c1c1e13aec762081
Signed-off-by: Michael Ru <mru@codeaurora.org>
Removes files and version checks for unsupported DSI PHY versions.
Change-Id: I47223a3860e3bcf48eb3b74e405064d8eb375f16
Signed-off-by: Michael Ru <mru@codeaurora.org>
Change adds the new compatible version strings for DSI PHY and DSI CTRL
for waipio.
Change-Id: I1073034e608cace9d41cc04a9854f15f56828dfe
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Change avoids clock framework APIs to configure the DSI PHY
PLL. It follows HW recommendation to set the byte and pclk
dividers.
Change-Id: I8c110f3997e4ec4c2eaa28778b70091855725ab8
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change allows dynamic refresh trigger to sw trigger
and mdp intf flush. With this we can make sure that DSI
timing/clock update and mdp intf timings are updated in
one vsync.
Change-Id: Ic807f498e2e47be6dd0f1e11ff1fc0896a8ec758
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Add support to read cphy boolean flag from panel dtsi
and configure DSI PHY registers accordingly. Update the
bit/byte clock calculation according to cphy specifications.
Update clock parents so that the relevant divider blocks
are configured to support cphy.
Change-Id: Iaca61eec01a488657b086f59910c52f8c79e26a4
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Yuan Zhao <yzhao@codeaurora.org>
DSI PLL is tightly coupled with DSI PHY. This change removes
separate DSI pll driver and makes DSI pll as a subnode to DSI
PHY which is an accurate way of representation. In addition, this
change adds support for 5nm DSI ctrl and PHY revisions and adds
DSI pll support for 5nm. Remove support for older DSI pll revisions
such as 7nm, 10nm, 14nm, 20nm, 28nm.
Change-Id: Ic8b886a9fe24b906e4ec5130720600efa1e59b68
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
DSI PHY timings must be committed every time the values
are updated after a dynamic mode switch.
Change-Id: Id605c76dfe75ec41ceb89000f24baccda189e82f
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
Adding debug, info and error prefix for log messages
in dsi files. To enable debug logs
run "echo 0x1 > /sys/module/drm/parameters/debug"
Change-Id: I438ac16954bd1d39450f8adeb7fb17f9ea6f8140
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change is a snapshot of dsi files taken of 4.14
as of commit 764f7c2 (Merge remote-tracking branch
'quic/dev/msm-4.14-display' into msm-4.14)
Change-Id: I8361a844c35a4450f7800964a8da2741676fd6c7
Signed-off-by: Satya Rama Aditya Pinapala <psraditya30@codeaurora.org>
This change adds support for dynamic switching of dsi clocks
to avoid RF interference issues. Also with dynamic dsi clock
switch feature coming into picture, now populate the supported
refresh rate as list instead of providing a range. Modify the
logic to enumerate all the modes in dsi driver, taking dynamic
bit clocks, resolutions and refresh rates into account.
Change-Id: I5b6e62bc935cf2234bdd96fcb3c7537b4e735fff
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Ritesh Kumar <riteshk@codeaurora.org>
Signed-off-by: Yujun Zhang <yujunzhang@codeaurora.org>
This change brings msm display driver including sde,
dp, dsi, rotator, dsi pll and dp pll from base 4.19 kernel
project. It is first source code snapshot from base kernel project.
Change-Id: Iec864c064ce5ea04e170f24414c728684002f284
Signed-off-by: Narendra Muppalla <NarendraM@codeaurora.org>
