Felipe writes:
USB: changes for v5.5
We have TI's glue layer for the Cadence USB3 controller going
upstream. Tegra's XUDC driver is also going upstream with this pull
request.
Apart from these two big features, we have a bunch of patches switching
over to devm_platform_ioremap_resource() in order to simplify code a
little; and a non-critical fix for DWC3 usage via kexec.
* tag 'usb-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (44 commits)
usb: dwc3: of-simple: add a shutdown
usb: cdns3: Add TI specific wrapper driver
dt-bindings: usb: Add binding for the TI wrapper for Cadence USB3 controller
usb: mtu3: fix race condition about delayed_status
usb: gadget: Add UDC driver for tegra XUSB device mode controller
usb: dwc3: debug: Remove newline printout
usb: dwc2: use a longer core rest timeout in dwc2_core_reset()
usb: gadget: udc: lpc32xx: Use devm_platform_ioremap_resource() in lpc32xx_udc_probe()
USB: gadget: udc: clean up an indentation issue
usb: gadget: Quieten gadget config message
phy: renesas: rcar-gen3-usb2: Use platform_get_irq_optional() for optional irq
usb: gadget: Remove set but not used variable 'opts' in msg_do_config
usb: gadget: Remove set but not used variable 'opts' in acm_ms_do_config
usb: mtu3: add a new function to do status stage
usb: gadget: configfs: fix concurrent issue between composite APIs
usb: gadget: f_tcm: Provide support to get alternate setting in tcm function
usb: gadget: Correct NULL pointer checking in fsl gadget
usb: fsl: Remove unused variable
USB: dummy-hcd: use usb_urb_dir_in instead of usb_pipein
USB: dummy-hcd: increase max number of devices to 32
...
Raw NAND core
* Useless extra checks dropped.
* Updated the detection of the bad block markers position
Raw NAND controller drivers:
* Cadence : New driver
* Brcmnand: Support for flash-dma v0 + fixes
* Denali : Support for the legacy controller/chip DT representation
dropped
* Superfluous dev_err() calls removed
SPI NOR core changes:
- introduce 'struct spi_nor_controller_ops',
- clean the Register Operations methods,
- use dev_dbg insted of dev_err for low level info,
- fix retlen handling in sst_write(),
- fix silent truncations in spi_nor_read and spi_nor_read_raw(),
- fix the clearing of QE bit on lock()/unlock(),
- rework the disabling of the block write protection,
- rework the Quad Enable methods,
- make sure nor->spimem and nor->controller_ops are mutually exclusive,
- set default Quad Enable method for ISSI flashes,
- add support for few flashes.
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer,
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes.
The syscon binding is a pretty loose one, with everyone having a bunch of
vendor specific compatibles.
In order to start the effort to describe them using YAML, let's create a
binding that tolerates additional, not listed, compatibles.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the STM32 CRYP binding to DT schema format using json-schema
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the STM32 CRC binding to DT schema format using json-schema
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert the STM32 timers binding to DT schema format using json-schema
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Schema errors can cause make to exit before useful information is
printed. This leaves developers wondering what's wrong. It can be
overcome passing '-k' to make, but that's not an obvious solution.
There's 2 scenarios where this happens.
When using DT_SCHEMA_FILES to validate with a single schema, any error
in the schema results in processed-schema.yaml being empty causing a
make error. The result is the specific errors in the schema are never
shown because processed-schema.yaml is the first target built. Simply
making processed-schema.yaml last in extra-y ensures the full schema
validation with detailed error messages happen first.
The 2nd problem is while schema errors are ignored for
processed-schema.yaml, full validation of the schema still runs in
parallel and any schema validation errors will still stop the build when
running validation of dts files. The fix is to not add the schema
examples to extra-y in this case. This means 'dtbs_check' is no longer a
superset of 'dt_binding_check'. Update the documentation to make this
clear.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert Samsung Exynos Soc Power Domain bindings to DT schema format using
json-schema.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
We have the i915 security fixes to backmerge, but first
let's clear the decks for other drivers to avoid a bigger
mess.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the specific microchip,sdcal-inverted property to at91 sdhci
device binding.
This optional property describes how the SoC SDCAL pin is connected.
It could be handled at SiP, SoM or board level.
This property read by at91 sdhci driver will allow to put in place a
software workaround that would reduce power consumption.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new compatible to use the sdhc-arasan host controller driver
with the SDXC PHY to support on Intel's Lightning Mountain(LGM) SoC.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
NXP/FSL SoC driver updates for v5.5
RCPM driver for ARM SoCs
- add RCPM driver to manage the wakeup devices for QorIQ ARM SoCs (HW low
power states are supported in PSCI firmware)
- add API to PM wakeup framework to retrieve wakeup sources
* tag 'soc-fsl-next-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
PM: wakeup: Add routine to help fetch wakeup source object.
Link: https://lore.kernel.org/r/1573599595-31411-1-git-send-email-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Johan Hedberg says:
====================
pull request: linux-bluetooth 2019-11-11
Here's one more bluetooth-next pull request for the 5.5 kernel release.
- Several fixes for LE advertising
- Added PM support to hci_qca driver
- Added support for WCN3991 SoC in hci_qca driver
- Added DT bindings for BCM43540 module
- A few other small cleanups/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Define a compatible string for Realtek RTD1619 SoC family.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
By default, QorIQ SoC's RCPM register block is Big Endian. But
there are some exceptions, such as LS1088A and LS2088A, are
Little Endian. So add this optional property to help identify
them.
Actually LS2021A and other Layerscapes won't totally follow Chassis
2.1, so separate them from powerpc SoC.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Add support for ILI2117 touch controller. This controller is similar
to the ILI210x and ILI251x, except for the following differences:
- Reading out of touch data must happen at most 300 mS after the
interrupt line was asserted. No command must be sent, the data
are returned upon pure I2C read of 43 bytes long.
- Supports 10 simultaneous touch inputs.
- Touch data format is slightly different.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Rob Herring <robh@kernel.org> # for DT binding
Tested-by: Adam Ford <aford173@gmail.com> #imx6q-logicpd
Tested-by: Sven Van Asbroeck <TheSven73@gmail.com> # ILI2118A variant
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull ARM cpufreq drivers updates for v5.5 from Viresh Kumar:
"This pull request contains:
- Updates to ti-cpufreq driver and DT files to support new platforms
and migrate from opp-v1 bindings to opp-v2 bindings (H. Nikolaus
Schaller and Adam Ford).
- Merging of arm_big_little and vexpress-spc drivers and related
cleanup (Sudeep Holla).
- Fix for imx's default speed grade value (Anson Huang).
- Minor cleanup patch for s3c64xx (Nathan Chancellor).
- Fix CPU speed bin detection for sun50i (Ondrej Jirman)."
* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: sun50i: Fix CPU speed bin detection
cpufreq: vexpress-spc: find and skip duplicates when merging frequencies
cpufreq: vexpress-spc: use macros instead of hardcoded values for cluster ids
cpufreq: s3c64xx: Remove pointless NULL check in s3c64xx_cpufreq_driver_init
cpufreq: imx-cpufreq-dt: Correct i.MX8MN's default speed grade value
cpufreq: vexpress-spc: fix some coding style issues
cpufreq: vexpress-spc: remove lots of debug messages
cpufreq: vexpress-spc: drop unnessary cpufreq_arm_bL_ops abstraction
cpufreq: merge arm_big_little and vexpress-spc
cpufreq: scpi: remove stale/outdated comment about the driver
ARM: dts: Add OPP-V2 table for AM3517
cpufreq: ti-cpufreq: Add support for AM3517
ARM: dts: omap36xx: using OPP1G needs to control the abb_ldo
cpufreq: ti-cpufreq: omap36xx use "cpu0","vbb" if run in multi_regulator mode
ARM: dts: omap3: bulk convert compatible to be explicitly ti,omap3430 or ti,omap3630 or ti,am3517
DTS: bindings: omap: update bindings documentation
ARM: dts: omap34xx & omap36xx: replace opp-v1 tables by opp-v2 for
cpufreq: ti-cpufreq: add support for omap34xx and omap36xx
Now that we have the DT validation in place, let's convert the device tree
bindings for the Amlogic I2C Controller over to YAML schemas.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
