Ideally wake_tx_queue should be used regardless as
it is a requirement for reducing bufferbloat and
implementing airtime fairness in the future.
However some setups (typically low-end platforms
hosting QCA988X) suffer performance regressions
with the current wake_tx_queue implementation.
Therefore disable it unless it is really
beneficial with current codebase (which is when
firmware supports smart pull-push tx scheduling).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Otherwise the driver module will not be automatically probed.
Fixes: 9d7cffaf99 ("leds: Add driver for the ISSI IS31FL32xx family of LED controllers")
Fixes: e0442d7def ("leds: Add SN3218 and SN3216 support to the IS31FL32XX driver")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: David Rivshin <drivshin@allworx.com>
Acked-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
tick_nohz_start_idle is called before checking whether the idle tick can be
stopped. If the tick cannot be stopped, calling tick_nohz_start_idle() is
pointless and just wasting CPU cycles.
Only invoke tick_nohz_start_idle() when can_stop_idle_tick() returns true. A
short one minute observation of the effect on ARM64 shows a reduction of calls
by 1.5% thus optimizing the idle entry sequence.
[tglx: Massaged changelog ]
Co-developed-by: Sanjeev Yadav<sanjeev.yadav@spreadtrum.com>
Signed-off-by: Gaurav Jindal<gaurav.jindal@spreadtrum.com>
Link: http://lkml.kernel.org/r/20160714120416.GB21099@gaurav.jindal@spreadtrum.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It is seldom used in the kernel code and can be easily replaced by
either RELOCATABLE or PPC32. So there is no reason to keep a separate
kernel option for this.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
It makes no sense to keep two separate RELOCATABLE config entries for
ppc32 and ppc64 respectively. Merge them into one and move it to a
common place.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In the current code, the RELOCATABLE will be forcedly enabled when
enabling CRASH_DUMP. But for ppc32, the RELOCABLE also depend on
ADVANCED_OPTIONS and select NONSTATIC_KERNEL. This will cause the
following build error when CRASH_DUMP=y && ADVANCED_OPTIONS=n because
the select of NONSTATIC_KERNEL doesn't take effect.
arch/powerpc/include/asm/io.h: In function 'virt_to_phys':
arch/powerpc/include/asm/page.h:113:26: error: 'virt_phys_offset' undeclared (first use in this function)
#define VIRT_PHYS_OFFSET virt_phys_offset
^
It doesn't have any strong reasons to make the RELOCATABLE depend on
ADVANCED_OPTIONS. So remove this dependency to fix this issue.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The sysfs interface used to handle PowerVM hotplug events should use the
hotplug queue as well. PRRN events will soon be placing many hotplug
events on the queue at once and we will need ordinary hotplug events to
use the queue as well in order to ensure these events will still be handled
and that proper serialization is maintained during the PRRN event.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add handler for new hotplug interrupt. For memory and CPU hotplug events,
we will add the hotplug errorlog to the hotplug workqueue. Since PCI
hotplug is not currently supported in the kernel, PCI hotplug events are
written to the rtas_log_bug and are handled by rtas_errd.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In support of PAPR changes to add a new hotplug interrupt, introduce a
hotplug workqueue to avoid processing hotplug events in interrupt context.
We will also take advantage of the queue on PowerVM to ensure hotplug
events initiated from different sources (HMC and PRRN events) are handled
and serialized properly.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
If kzalloc() fails when allocating adapter->guest in
cxl_guest_init_adapter(), we call free_adapter() before erroring out.
free_adapter() in turn attempts to dereference adapter->guest, which in
this case is NULL.
In free_adapter(), skip the adapter->guest cleanup if adapter->guest is
NULL.
Fixes: 14baf4d9c7 ("cxl: Add guest-specific code")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Remove the CXL_KERNEL_API and CXL_EEH Kconfig options, as they were only
needed to coordinate the merging of the cxlflash driver. Also remove the
stub implementation of cxl_perst_reloads_same_image() in cxlflash which is
only used if CXL_EEH isn't defined (i.e. never).
Suggested-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Ian Munsie <imunsie@au1.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
pnv_cxl_enable_phb_kernel_api() grabs a reference to the cxl module to
prevent it from being unloaded after the PHB has been switched to CX4
mode. This breaks the build when CONFIG_MODULES=n as module_mutex
doesn't exist.
However, if we don't have modules, we don't need to protect against the
case of the cxl module being unloaded. As such, split the relevant code
out into a function surrounded with #if IS_MODULE(CXL) so we don't try
to compile it if cxl isn't being compiled as a module.
Fixes: 5918dbc9b4ec ("powerpc/powernv: Add support for the cxl kernel api on the real phb")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This makes it easy to verify we are not overloading the bits.
No functionality change by this patch.
mpe: Cleanup more. Completely fixup whitespace, convert all UL values to
ASM_CONST(), and replace all occurrences of 63-x with the actual shift.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
On May 4th, Bjørn Mork provided patch 697bbc7b83 ("builddeb: include
objtool binary in headers package"). However, that one only works if
$srctree=$objtree, because the objtool binaries are not written to the
srctree, but to the objtree.
Signed-off-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Fixes: 697bbc7b83 ("builddeb: include objtool binary in headers package")
Signed-off-by: Michal Marek <mmarek@suse.com>
The new affinity hint argument of __irq_domain_alloc_irqs() is missing in
irq_reserve_ipi(). Add it.
This fixes the following compilation error:
kernel/irq/ipi.c: In function ‘irq_reserve_ipi’:
kernel/irq/ipi.c:85:9: error: too few arguments to function ‘__irq_domain_alloc_irqs’
virq = __irq_domain_alloc_irqs(domain, virq, nr_irqs, NUMA_NO_NODE,
^
Fixes: 06ee6d571f ("genirq: Add affinity hint to irq allocation")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: linux-pci@vger.kernel.org
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The drm_irq docs want one function from drmP.h, but that one is a
serious mess. Extract it, and while at it improve the docs a bit.
There's a bit a header loop issue since core data structures like
drm_device and drm_driver aren't in their own headers yet, which means
the drm_irq.h include in drmP.h needs to be in just the right spot :(
Also noticed that drm_vblank_crtc->last_wait is entirely unused,
remove it.
v2: git add drm_irq.h ...
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The watchdog status function is supposed to return WDIOF_ flags,
not internal status flags. The available WDIOF_ flags are now
returned by the watchdog core, so the status function in this driver
is unnecessary.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Up to now, the watchdog status function called a driver function,
which was supposed to return the watchdog status. All but one
driver using the watchdog core did not implement this function,
and the driver implementing it did not implement it correctly
(the function is supposed to return WDIOF_ flags). At the same time,
at least some of the status information can be provided by the watchdog
core.
Provide the available status bits directly from the watchdog driver core.
Call the driver status function if it exists to get the boot status, but
always provide WDIOF_MAGICCLOSE and WDIOF_KEEPALIVEPING internally.
This patch makes the 'status' sysfs attribute always available.
This attribute is now displayed as hex number with 0x prepended to be
easier to decode.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
As promised here's the pile of kbl cherry-picks assembled by Mika&Rodrigo.
It's a bit much, but all well-contained to kbl code and been tested for a
while in drm-intel-next. Still separate in case too much, but in that case
I think we'd need to disable kbl by default again (which would be annoying
too) in 4.7.
* tag 'topic/kbl-4.7-fixes-2016-07-18' of git://anongit.freedesktop.org/drm-intel: (28 commits)
drm/i915/kbl: Introduce the first official DMC for Kabylake.
drm/i915: Introduce Kabypoint PCH for Kabylake H/DT.
drm/i915/gen9: implement WaConextSwitchWithConcurrentTLBInvalidate
drm/i915/gen9: Add WaFbcHighMemBwCorruptionAvoidance
drm/i195/fbc: Add WaFbcNukeOnHostModify
drm/i915/gen9: Add WaFbcWakeMemOn
drm/i915/gen9: Add WaFbcTurnOffFbcWatermark
drm/i915/kbl: Add WaClearSlmSpaceAtContextSwitch
drm/i915/gen9: Add WaEnableChickenDCPR
drm/i915/kbl: Add WaDisableSbeCacheDispatchPortSharing
drm/i915/kbl: Add WaDisableGafsUnitClkGating
drm/i915/kbl: Add WaForGAMHang
drm/i915: Add WaInsertDummyPushConstP for bxt and kbl
drm/i915/kbl: Add WaDisableDynamicCreditSharing
drm/i915/kbl: Add WaDisableGamClockGating
drm/i915/gen9: Enable must set chicken bits in config0 reg
drm/i915/kbl: Add WaDisableLSQCROPERFforOCL
drm/i915/kbl: Add WaDisableSDEUnitClockGating
drm/i915/kbl: Add WaDisableFenceDestinationToSLM for A0
drm/i915/kbl: Add WaEnableGapsTsvCreditFix
...
This is an update to the previous drm bridge pull request. The ADV7511
driver's conversion from slave encoder to bridge meant that its users
(the rcar-du kms driver) should use the bridge interface too. This pull
request now also contains a commit that updates the rcar-du's hdmi encoder
interface from slave encoder to bridge.
The other updates are as before:
- Converts the ADV7511 i2c slave encoder driver to a bridge driver.
Adds support for the ADV7533 bridge chip.
- Add bridge driver for TC358767 (DSI/DPI to eDP) encoder chips.
* 'drm_bridge_for_4.8' of https://github.com/boddob/linux:
drm: rcar-du: Remove i2c slave encoder interface for hdmi encoder
drm/bridge: tc358767: Add DPI to eDP bridge driver
dt-bindings: tc358767: add DT documentation
dt-bindings: drm/bridge: Update bindings for ADV7533
drm/bridge: adv7533: Change number of DSI lanes dynamically
drm/bridge: adv7533: Use internal timing generator
drm/bridge: adv7533: Create a MIPI DSI device
drm/bridge: adv7533: Initial support for ADV7533
drm/bridge: adv7511: Fix mutex deadlock when interrupts are disabled
drm/i2c: adv7511: Move to bridge folder
drm/i2c: adv7511: Convert to drm_bridge
This patch add XTS subroutines using VMX-crypto driver.
It gives a boost of 20 times using XTS.
These code has been adopted from OpenSSL project in collaboration
with the original author (Andy Polyakov <appro@openssl.org>).
Signed-off-by: Leonidas S. Barbosa <leosilva@linux.vnet.ibm.com>
Signed-off-by: Paulo Flabiano Smorigo <pfsmorigo@linux.vnet.ibm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When an akcipher test fails, we don't know which algorithm failed
because the name is not printed. This patch fixes this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the parameter 'gfp_flags' instead of 'flag' as second argument of
dma_pool_alloc(). The parameter 'flag' is for the TDMA descriptor, its
content has no sense for the allocator.
Fixes: bac8e805a3 ("crypto: marvell - Copy IV vectors by DMA...")
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Backmerge drm-next to be able to apply Chris' connector_unregister_all
cleanup (need latest i915 and sun4i state for that).
Also there's a trivial conflict in ttm_bo.c that git rerere fails to
remember.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Unfortunately, there's two situations where we lose hpd right now:
- Runtime suspend
- When we've shut off all of the power wells on Valleyview/Cherryview
While it would be nice if this didn't cause issues, this has the
ability to get us in some awkward states where a user won't be able to
get their display to turn on. For instance; if we boot a Valleyview
system without any monitors connected, it won't need any of it's power
wells and thus shut them off. Since this causes us to lose HPD, this
means that unless the user knows how to ssh into their machine and do a
manual reprobe for monitors, none of the monitors they connect after
booting will actually work.
Eventually we should come up with a better fix then having to enable
polling for this, since this makes rpm a lot less useful, but for now
the infrastructure in i915 just isn't there yet to get hpd in these
situations.
Changes since v1:
- Add comment explaining the addition of the if
(!mode_config->poll_running) in intel_hpd_init()
- Remove unneeded if (!dev->mode_config.poll_enabled) in
i915_hpd_poll_init_work()
- Call to drm_helper_hpd_irq_event() after we disable polling
- Add cancel_work_sync() call to intel_hpd_cancel_work()
Changes since v2:
- Apparently dev->mode_config.poll_running doesn't actually reflect
whether or not a poll is currently in progress, and is actually used
for dynamic module paramter enabling/disabling. So now we instead
keep track of our own poll_running variable in dev_priv->hotplug
- Clean i915_hpd_poll_init_work() a little bit
Changes since v3:
- Remove the now-redundant connector loop in intel_hpd_init(), just
rely on intel_hpd_poll_enable() for setting connector->polled
correctly on each connector
- Get rid of poll_running
- Don't assign enabled in i915_hpd_poll_init_work before we actually
lock dev->mode_config.mutex
- Wrap enabled assignment in i915_hpd_poll_init_work() in READ_ONCE()
for doc purposes
- Do the same for dev_priv->hotplug.poll_enabled with WRITE_ONCE in
intel_hpd_poll_enable()
- Add some comments about racing not mattering in intel_hpd_poll_enable
Changes since v4:
- Rename intel_hpd_poll_enable() to intel_hpd_poll_init()
- Drop the bool argument from intel_hpd_poll_init()
- Remove redundant calls to intel_hpd_poll_init()
- Rename poll_enable_work to poll_init_work
- Add some kerneldoc for intel_hpd_poll_init()
- Cross-reference intel_hpd_poll_init() in intel_hpd_init()
- Just copy the loop from intel_hpd_init() in intel_hpd_poll_init()
Changes since v5:
- Minor kerneldoc nitpicks
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 19625e85c6)
One of the things preventing us from using polling is the fact that
calling valleyview_crt_detect_hotplug() when there's a VGA cable
connected results in sending another hotplug. With polling enabled when
HPD is disabled, this results in a scenario like this:
- We enable power wells and reset the ADPA
- output_poll_exec does force probe on VGA, triggering a hpd
- HPD handler waits for poll to unlock dev->mode_config.mutex
- output_poll_exec shuts off the ADPA, unlocks dev->mode_config.mutex
- HPD handler runs, resets ADPA and brings us back to the start
This results in an endless irq storm getting sent from the ADPA
whenever a VGA connector gets detected in the middle of polling.
Somewhat based off of the "drm/i915: Disable CRT HPD around force
trigger" patch Ville Syrjälä sent a while back
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit b236d7c842)
While VGA hotplugging worked(ish) before, it looks like that was mainly
because we'd unintentionally enable it in
valleyview_crt_detect_hotplug() when we did a force trigger. This
doesn't work reliably enough because whenever the display powerwell on
vlv gets disabled, the values set in VLV_ADPA get cleared and
consequently VGA hotplugging gets disabled. This causes bugs such as one
we found on an Intel NUC, where doing the following sequence of
hotplugs:
- Disconnect all monitors
- Connect VGA
- Disconnect VGA
- Connect HDMI
Would result in VGA hotplugging becoming disabled, due to the powerwells
getting toggled in the process of connecting HDMI.
Changes since v3:
- Expose intel_crt_reset() through intel_drv.h and call that in
vlv_display_power_well_init() instead of
encoder->base.funcs->reset(&encoder->base);
Changes since v2:
- Use intel_encoder structs instead of drm_encoder structs
Changes since v1:
- Instead of handling the register writes ourself, we just reuse
intel_crt_detect()
- Instead of resetting the ADPA during display IRQ installation, we now
reset them in vlv_display_power_well_init()
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rebase over dev_priv/drm_device embedding.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 9504a89247)
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
User visible changes:
- Properly report when a function wildcard produces no matches in 'perf probe'
(Masami Hiramatsu)
- Balance opening and reading events in 'perf stat', which could cause
it to get stuck trying to close invalid file descriptors (Mark Rutland)
Infrastructure changes:
- Copy more headers from the kernel, this time for headers that
were just including the contents of its kernel counterparts, should
help resolving the problems with linux-next, where some uapi related
patches seem to be breaking tools/object/ build. (Arnaldo Carvalho de Melo)
Some more combing will be done, but at least it is possible to build
perf out of tree, via a detached tarball (make help | grep perf),
without including kernel files in its MANIFEST (Arnaldo Carvalho de Melo)
- Fix smatch found errors that were not causing problems, but are
mistakes nonetheless (Dan Carpenter)
- Fix string vs. byte array resolving in the python script code (Jiri Olsa)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
