This patch adds external interrupt (exti) support
on stm32mp157c SoC.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Commit 15122ee2c5 ("arm64: Enforce BBM for huge IO/VMAP mappings")
disallowed block mappings for ioremap since that code does not honor
break-before-make. The same APIs are also used for permission updating
though and the extra checks prevent the permission updates from happening,
even though this should be permitted. This results in read-only permissions
not being fully applied. Visibly, this can occasionaly be seen as a failure
on the built in rodata test when the test data ends up in a section or
as an odd RW gap on the page table dump. Fix this by using
pgattr_change_is_safe instead of p*d_present for determining if the
change is permitted.
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Fixes: 15122ee2c5 ("arm64: Enforce BBM for huge IO/VMAP mappings")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
If 020/030 support is enabled, get_io_area() leaves an IO_SIZE gap
between mappings which is added to the vm_struct representing the
mapping. __ioremap() uses the actual requested size (after alignment),
while __iounmap() is passed the size from the vm_struct.
On 020/030, early termination descriptors are used to set up mappings of
extent 'size', which are validated on unmapping. The unmapped gap of
size IO_SIZE defeats the sanity check of the pmd tables, causing
__iounmap() to loop forever on 030.
On 040/060, unmapping of page table entries does not check for a valid
mapping, so the umapping loop always completes there.
Adjust size to be unmapped by the gap that had been added in the
vm_struct prior.
This fixes the hang in atari_platform_init() reported a long time ago,
and a similar one reported by Finn recently (addressed by removing
ioremap() use from the SWIM driver.
Tested on my Falcon in 030 mode - untested but should work the same on
040/060 (the extra page tables cleared there would never have been set
up anyway).
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
[geert: Minor commit description improvements]
[geert: This was fixed in 2.4.23, but not in 2.5.x]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
This adds support for bpf-to-bpf function calls in the powerpc64
JIT compiler. The JIT compiler converts the bpf call instructions
to native branch instructions. After a round of the usual passes,
the start addresses of the JITed images for the callee functions
are known. Finally, to fixup the branch target addresses, we need
to perform an extra pass.
Because of the address range in which JITed images are allocated
on powerpc64, the offsets of the start addresses of these images
from __bpf_call_base are as large as 64 bits. So, for a function
call, we cannot use the imm field of the instruction to determine
the callee's address. Instead, we use the alternative method of
getting it from the list of function addresses in the auxiliary
data of the caller by using the off field as an index.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
For multi-function programs, loading the address of a callee
function to a register requires emitting instructions whose
count varies from one to five depending on the nature of the
address.
Since we come to know of the callee's address only before the
extra pass, the number of instructions required to load this
address may vary from what was previously generated. This can
make the JITed image grow or shrink.
To avoid this, we should generate a constant five-instruction
when loading function addresses by padding the optimized load
sequence with NOPs.
Signed-off-by: Sandipan Das <sandipan@linux.vnet.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
fix below warning about PPI interrupts configuration:
"GIC: PPI13 is secure or misconfigured"
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
fix below warning about PPI interrupts configuration:
"GIC: PPI13 is secure or misconfigured"
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Without this property, we get this boot warning:
"L2C: device tree omits to specify unified cache"
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Control the Chromecast's two LEDs using PWM instead of GPIO pins. This
allows for variable brightness.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
On the Chromecast, the bootloader provides us with an ATAG_MEM of
start=0x01000000 and size=0x3eff8000. This is clearly incorrect, as the
range given encompasses nearly a GiB but the Chromecast only has 512MiB
of RAM! Additionally, this causes the kernel to be decompressed at
0x00008000, below the claimed beginning of RAM, and so the boot fails.
Since the existing ATAG parsing code runs before the kernel is even
decompressed and irrevocably patches the device tree, don't even try
to bypass it. Instead, use the "linux,usable-memory" property instead
of the "reg" property to define the real range. The ATAG code only
overwrites reg, but linux,usable-memory is checked first in the OF
driver, so the fact that reg gets changed makes no difference.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Valve Steam Link is a consumer device built around the Marvell BG2CD SoC.
This board file enables the UART, USB and Ethernet interfaces as well as
internal I2C and SDIO, and adds SoC voltage regulator and board-specific
GPIO restart method info.
Cc: Sam Lantinga <saml@valvesoftware.com>
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
This adds most of the remaining Designware IP cores under APB trees in
the interest of documenting assignment of interrupts and memory ranges.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
This adds DT nodes for the Cortex-A9 MPCore SCU, local watchdog and
most importantly the global timer.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Cortex-A9 PMU has no associated memory ranges and "make dtbs W=1" warns
about missing reg or ranges property. To avoid the warning, move the PMU
node out of soc subtree to the root.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Use the correct trigger type for Cortex-A9. This was fixed for several
other SoCs since the kernel started issuing a boot-time warning.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
I believe the flush_cache_all() after scu_enable() is to "Ensure that
the data accessed by CPU0 before the SCU was initialised is visible
to the other CPUs." as commented in scu_enable(). So here
flush_cache_all() is a duplication, remove it.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
BG2CD SoC uses r3p0 Cortex-A9 MPCore single-CPU cluster. Autoselect
pertinent errata, the SCU and the global timer, and allow use of the
local timer on uniprocessor kernels.
PL310 L2 cache controller has revision r3p2; no errata to select.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
This patch exports tm_enable()/tm_disable/tm_abort() APIs, which
will be used for PR KVM transactional memory logic.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patches add some macros for CR0/TEXASR bits so that PR KVM TM
logic (tbegin./treclaim./tabort.) can make use of them later.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
PR KVM will need to reuse msr_check_and_set().
This patch exports this API for reuse.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Add the save and restore for clksrc as part of suspend and resume
so that it saves the counter value and restores. This is needed in
modes like rtc+ddr in self-refresh not doing this stalls the time.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These registers are part of the wkup domain and are lost during RTC only
suspend and also hibernation, so storing/restoring their state is
necessary.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now as the Amstrad Delta board provides GPIO lookup tables, switch from
GPIO numbers to GPIO descriptors and use the table to locate required
GPIO pins.
The card uses two pins, one for jack and the other for voice modem
codec DAI control.
For jack pin, remove hardcoded GPIO number and use GPIO descriptor
based variant of jack GPIO initialization.
For modem_codec pin, declare static variable for storing its GPIO
descriptor, obtain it on card initialization and replace obsolete
ams_delta_latch2_write() with gpiod_set_value(). For that to work,
don't request the modem_codec pin from the board init code anymore.
If the modem_codec GPIO lookup fails, skip initialization of
functionality of the card which depends on its availability.
Pin naming used by the driver should be followed while respective GPIO
lookup table is initialized by a board init code.
Created and tested against linux-4.17-rc3, on top of patch 1/6 "ARM:
OMAP1: ams-delta: add GPIO lookup tables"
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Scope of the change is limited to GPIO pins used by board specific
device drivers which will be updated by follow-up patches of the
series. Those are some OMAP GPIO (gpio-0-15) and most of Amstrad Delta
latch2 GPIO bank pins. Remaining pins of those banks, as well as
Amstrad Delta latch1 pins, will be addressed later.
Assign a label ("latch2") to the bank, enumerate its pins and put that
information, together with OMAP GPIO bank pins, in GPIO lookup tables.
Assign lookup tables to devices as soon as those devices are registered
and their names can be obtained.
A step froward in:
- removal of hard-coded GPIO numbers from drivers,
- removal of board mach includes from drivers,
- switching to dynamically assigned GPIO numbers.
Created and compile tested agains linux-4.17-rc3
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
>From the hardware perspective, the actual pclk of the AO uarts
is the corresponding clkc_ao uart gate, not the main clock controller clk81.
This was not problem so far, because the uart_gate had
the CLK_IGNORE_UNUSED flag, which kept the gate open.
We plan to remove the CLK_IGNORE_UNUSED flag in another patch,
but before doing that, we need to fix the clock in the DTS file.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add all '1x' clocks to decon and decontv devices. Enabling those clocks
is needed to get proper display on hardware windows no 4 and 5.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Currently there are no differences between the MACH_MESON8 and
MACH_MESON8B Kconfig symbols (except the help text). Since both
platforms are very similar (Meson8b being a slightly updated,
cost-reduced version of Meson8 which even shares some peripherals with
Meson8m2) no notable differences are expected in the future either.
Suggested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Currently there are two identical Kconfig options where only differences
are the Kconfig help text and the list of .dtbs that are built:
- MACH_MESON8
- MACH_MESON8B
Build the Meson8b .dtbs when MACH_MESON8 is selected to get rid of the
latter Kconfig symbol later.
Suggested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The i2c AO is used for the MIC daughter card of the S400 board
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the pins related to the i2c AO controller of the meson-axg platform
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock specified for the i2c AO controller is the one for the EE
domain, which is incorrect as this controller needs the clock for AO
i2c controller.
Fixes: dc6f858e26 ("ARM64: dts: meson-axg: add I2C DT info for Meson-AXG SoC")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Remove undocumented and unused "clk_i2c" clock name and the second
interrupt from i2c nodes of meson-axg platform. Those seems to have
been copy/pasted from the vendor kernel
Fixes: dc6f858e26 ("ARM64: dts: meson-axg: add I2C DT info for Meson-AXG SoC")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enforce the invariant that existing VMCS12 field offsets must not
change. Experience has shown that without strict enforcement, this
invariant will not be maintained.
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[Changed the code to use BUILD_BUG_ON_MSG instead of better, but GCC 4.6
requiring _Static_assert. - Radim.]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Pull alpha fixes from Matt Turner:
"A few small changes for alpha"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha:
alpha: io: reorder barriers to guarantee writeX() and iowriteX() ordering #2
alpha: simplify get_arch_dma_ops
alpha: use dma_direct_ops for jensen
Changing the VMCS12 layout will break save/restore compatibility with
older kvm releases once the KVM_{GET,SET}_NESTED_STATE ioctls are
accepted upstream. Google has already been using these ioctls for some
time, and we implore the community not to disturb the existing layout.
Move the four most recently added fields to preserve the offsets of
the previously defined fields and reserve locations for the vmread and
vmwrite bitmaps, which will be used in the virtualization of VMCS
shadowing (to improve the performance of double-nesting).
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[Kept the SDM order in vmcs_field_to_offset_table. - Radim]
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
The hypercall was added using a struct timespec based implementation,
but we should not use timespec in new code.
This changes it to timespec64. There is no functional change
here since the implementation is only used in 64-bit kernels
that use the same definition for timespec and timespec64.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
When saving a vCPU's nested state, the vmcs02 is discarded. Only the
shadow vmcs12 is saved. The shadow vmcs12 contains all of the
information needed to reconstruct an equivalent vmcs02 on restore, but
we have to be able to deal with two contexts:
1. The nested state was saved immediately after an emulated VM-entry,
before the vmcs02 was ever launched.
2. The nested state was saved some time after the first successful
launch of the vmcs02.
Though it's an implementation detail rather than an architected bit,
vmx->nested_run_pending serves to distinguish between these two
cases. Hence, we save it as part of the vCPU's nested state. (Yes,
this is ugly.)
Even when restoring from a checkpoint, it may be necessary to build
the vmcs02 as if prepare_vmcs02 was called from nested_vmx_run. So,
the 'from_vmentry' argument should be dropped, and
vmx->nested_run_pending should be consulted instead. The nested state
restoration code then has to set vmx->nested_run_pending prior to
calling prepare_vmcs02. It's important that the restoration code set
vmx->nested_run_pending anyway, since the flag impacts things like
interrupt delivery as well.
Fixes: cf8b84f48a ("kvm: nVMX: Prepare for checkpointing L2 state")
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
In do_page_fault(), we handle some kernel faults early, and simply
die() with a message. For faults handled later, we dump the faulting
address, decode the ESR, walk the page tables, and perform a number of
steps to ensure that this data is reported.
Let's unify the handling of fatal kernel faults with a new
die_kernel_fault() helper, handling all of these details. This is
largely the same as the existing logic in __do_kernel_fault(), except
that addresses are consistently padded to 16 hex characters, as would be
expected for a 64-bit address.
The messages currently logged in do_page_fault are adjusted to fit into
the die_kernel_fault() message template.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The naming of is_permission_fault() makes it sound like it should return
true for permission faults from EL0, but by design, it only does so for
faults from EL1.
Let's make this clear by dropping el1 in the name, as we do for
is_el1_instruction_abort().
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
