Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The Bananapi M2 Ultra has a Realtek RTL8211E RGMII PHY tied to the GMAC.
The PMIC's DC1SW output provides power for the PHY, while the ALDO2
output provides I/O voltages on both sides.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The R40 SoC has a GMAC (gigabit capable Ethernet controller). Add a
device node for it. The only publicly available board for this SoC
uses an RGMII PHY. Add a pinmux node for it as well.
Since this SoC also has an old 10/100 Mbps EMAC, which also has an
MDIO bus controller, the MDIO bus for the GMAC is labeled "gmac_mdio".
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The device nodes dereference (&foo) usages should be sorted by the label
names, barring any parsing order issues such as the #include statement
for the PMIC's .dtsi file that must come after the PMIC.
Move the mmc and ohci blocks in front of the PMIC's regulator blocks.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The legacy mode uses the write protect and card detect but DT does not.
This patch enables Write-Protect and Card-Detect pins for the MMC card, and
the gpio-ranges property sets the gpio pinmuxing for those respective pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Fixed pin numbers for uart4 on rk3288, iommu clocks and small changes
over multiple boards like default serial setting for rk3288-tinker,
output selection for the dp83867 on the phycore-som and the newly
added pwm-backlight delay properties for veyron boards.
* tag 'v4.18-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: default serial for rk3288 Tinker Board
ARM: dts: rockchip: set PWM delay backlight settings for Minnie
ARM: dts: rockchip: set PWM delay backlight settings for Veyron
ARM: dts: rockchip: add clocks in iommu nodes
ARM: dts: rockchip: Add dp83867 CLK_OUT muxing on rk3288-phycore-som
ARM: dts: rockchip: fix uart4 pin-numbers for rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
ARMv7 Vexpress updates/cleanups for v4.18
1. Syntactic restructuring of motherboard include file so that it can be
included at the top of any other DTS file as it should be rather than
existing include in the middle of the file at a specific location
2. Use of standard GPIO controller bindings for few sysreg components
like LED, MMC Write Protect/Card Detect and Flash Write Protect
to fix some of the new DTC warnings
3. Cleanup to replace all underscores('_') with hyphens('-') in the
device node names
* tag 'vexpress-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: replace '_' with '-' in node names
ARM: dts: vexpress: use standard gpio bindings for sys_{led,mci,flash}
ARM: dts: vexpress: Restructure motherboard includes
Signed-off-by: Olof Johansson <olof@lixom.net>
The touchscreen patch did not apply to this branch correctly and
inadvertently got placed onto I2C2 when it should be on I2C3. This fixes
the issue.
Fixes: 121685b146 ("ARM: dts: logicpd-som-lv: Enable Touchscreen
controller")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SOM used in the am3517-evm has a s35390a onboard. This
patch allows the s35390a to be used as the RTC.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
enable mmc3 used for wlan and uart1 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM3517-EVM by Logic PD has a Logic PD type 15 display LCD
attached to the baseboard, and the SOM itself has an integrated
touchscreen controller. This patch enables both the LCD and
the tsc2004 on the SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The am3517-som is powered by vdd_core_reg, so let's add the
'cpu' device-tree node with the 'vdd_core' regulator as the core
supply.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit adds the common voltage regulators used on LogicPD's
AM3517 System-On-Modules.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The am3517-evm consists of an am3517 SOM-M2 and a baseboard.
As items are added that are unique to the baseboard, let's place
them in a file called am3517-som.dtsi. These items will be
common for all variants of the SOM.
Anything unique to the baseboard will be placed into
am3517-evm.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses 26MHz oscillator for the twl4030 HFCLK. This way we will
not depend on the bootloader to configure the CFG_BOOT:HFCLK_FREQ
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses 26MHz oscillator for the twl4030 HFCLK.
This way we will not depend on the bootloader to configure the
CFG_BOOT:HFCLK_FREQ
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace magic number with the proper IRQ_TYPE specifier to improve DT
readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 561f9bcf26.
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes: 561f9bcf26 ("ARM: dts: am437x-sk-evm: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes: 7a53a34622 ("ARM: dts: am437x-epos-evm: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes: b997f534b5 ("ARM: dts: am437x-cm-t43: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes: 5692b911c9 ("ARM: dts: am437x-gp-evm: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 CM-T3x based boards define 2 /connector nodes for S-Video and
DVI output. However, since they have the same node name, the S-Video
connector overwritten. This leaves a dangling graph connection which
gives the following warning:
arch/arm/boot/dts/omap3-sbc-t3517.dtb: Warning (graph_endpoint):
/ocp@68000000/dss@48050000/encoder@48050c00/port/endpoint: graph
connection to node '/connector/port/endpoint' is not bidirectional
Fix this by renaming the nodes to s-video-connector and dvi-connector.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap3-devkit8000-common.dtsi defines a graph connection for DVI, but
then omap3-devkit8000-lcd-common.dtsi overrides that with a graph
connection for the LCD as the same output signals are used. This
leaves an incomplete graph as the TFP410 output has only half a
connection. The result is the following warning:
arch/arm/boot/dts/omap3-devkit8000-lcd70.dtb: Warning (graph_endpoint):
/encoder0/ports/port@0/endpoint: graph connection to node
'/ocp@68000000/dss@48050000/port/endpoint' is not bidirectional
Fix this by defining multiple endpoints which is the correct way to show
a 1 to many connection.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch switches Odroid X/X2/U3 to use dedicated Odroid audio subsystem
DT bindings instead of the simple-card in order to add support for audio
over HDMI.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace magic number with the proper IRQ_TYPE specifier to improve DT
readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace magic number with the proper IRQ_TYPE specifier to improve DT
readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace magic number with the proper IRQ_TYPE specifier to improve DT
readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Samsung DTS ARM changes for v4.18
1. Add support for USB OTG port on Origen board.
2. Allow earlycon on Rinato board.
3. Cleanup from obsolete properties.
4. Fix DTC warnings.
5. Remove Exynos5440 entirely.
6. Add mem-2-mem Scaler devices.
* tag 'samsung-dt-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Update x and y properties for mms114 touchscreen
ARM: dts: exynos: Add mem-2-mem Scaler devices
ARM: dts: s3c64xx: Remove skeleton.dtsi and fix DTC warnings for /memory
ARM: dts: s3c24xx: Fix unnecessary address/size cells DTC warnings
ARM: dts: s3c24xx: Remove skeleton.dtsi and fix DTC warning for /memory
ARM: dts: exynos/s3c: Remove leading 0x and 0s from bindings notation
ARM: dts: exynos: Remove Exynos5440
ARM: dts: exynos: Remove unnecessary address/size properties in dp-controller of Exynos5
ARM: dts: exynos: Bring order in fixed-regulators naming in Midas boards
ARM: dts: exynos: Remove regulators node container in Origen and N710x
ARM: dts: exynos: Remove unnecessary address/size properties in Origen
ARM: dts: exynos: Remove unnecessary address/size properties in Midas boards
ARM: dts: exynos: Fix invalid node referenced by i2c20 alias in Peach Pit and Pi
ARM: dts: exynos: Move syscon poweroff and restart nodes under the PMU
ARM: dts: exynos: Remove obsolete clock properties from power domains
ARM: dts: exynos: Add serial path for Rinato board to get earlycon support
ARM: dts: exynos: Add support for USB OTG port on Origen board
Signed-off-by: Olof Johansson <olof@lixom.net>
DTS updates for the Gemini:
- Set righ flashes on DNS-313
- Activate ATA1 on NAS4220B
- Set right harddisk triggers on the D-Link devices
- Fix all DTC warnings
* tag 'gemini-dts-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Fix DTC warnings
ARM: dts: Add second ATA to NAS4220B
ARM: dts: Fix bootargs for Gemini D-Link devices
ARM: dts: Fix the DNS-313 flash compatible
ARM: dts: Set DNS-685 LEDs to use better triggers
ARM: dtd: Set DNS-313 LEDs to use better triggers
ARM: dts: gemini: Fix "debounce-interval" property misspelling
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request contains Broadcom ARM-based SoC Device Tree changes
for 4.18, please pull the following:
- Stefan provides updates to the BCM2835 RNG Device Tree binding and
Device Tree node by adding its missing interrupt line.
- Rafal switches the Luxul XWC-1000 and the D-Link DIR-885L to the new
partitions syntax which allows specifying a partition parser
- Rafal also updates a bunch of BCM5301X Device Tree source files to a
more standard SPDX tag and dual GPL 2.0 and MIT. This is a follow-up
to this discussion with Greg:
https://lkml.org/lkml/2018/4/28/179
- Dan adds support for two Luxul devices: XAP-1610 (based on BCM47094)
and XWR-3150 V1 (similar to XWR-3100)
- Stefan provides a set of updates to the BCM283x Device Tree sources to
support the Raspberry Pi 3 B+ for both the ARM and ARM64 kernels. He
adds the required nodes for the LAN7515 USB Ethernet, Cypress CYW43455
BT/WiFi combo chip. Stefan also provides a few fixes for the PWM pin
assignment for RPi 3B and Zero/Zero W. Finally, Stefan adds the
missing GPIOs for controlling additional peripherals now that support
for the RPi 3 GPIO expander has landed
* tag 'arm-soc/for-4.18/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Switch D-Link DIR-885L to the new partitions syntax
ARM: dts: BCM5301X: Relicense Asus RT-AC87U file to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Add DT for Luxul XAP-1610
ARM: dts: BCM5301X: Add DT for Luxul XWR-3150 V1
ARM: dts: BCM5301X: Relicense Buffalo files to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Relicense most DTS files to the GPL 2.0+ / MIT
arm64: dts: broadcom: Add reference to Raspberry Pi 3 B+
ARM: dts: bcm2837: Add Raspberry Pi 3 B+
dt-bindings: bcm: Add Raspberry Pi 3 B+
ARM: dts: bcm2837: Add missing GPIOs of Expander
ARM: dts: bcm283x: Fix PWM pin assignment
ARM: dts: BCM5301X: Switch Luxul XWC-1000 to the new fixed partitions syntax
ARM: bcm283x: Add missing interrupt for RNG block
dt-binding: rng: Add interrupt property for BCM2835
Signed-off-by: Olof Johansson <olof@lixom.net>
For PCI, the second and third cell in ranges specifies the upper and
lower target address for address translation. This target address will
be used to program the internal address translation unit (iATU).
The current device tree configuration will program the iATU to translate
CPU accesses to 0x08000000 to PCI address 0x0 (with TLP type MEM).
The device tree configuration also specifies that CPU acesses to
0x0fe00000 will be translated to PCI address 0x0 (with TLP type I/O).
We cannot have both I/O space and memory space at PCI address 0x0.
The PCI code already uses the CPU address when assigning addresses to
memory BARs, so for memory space the PCI address should be the same as
the CPU address. This also matches how all other device trees using
snps,dw-pcie are configured.
The existing configuration appears to work, even if it is incorrect.
For some reason the iATU doesn't obey the existing configuration,
and doesn't translate CPU accesses from 0x08000000 to PCI address 0x0.
The reason why the existing configuration works at all is probably
because the default behavior, when there is no match, is to use the
untranslated address. This happens to work for memory space, since
it's a 1:1 mapping. However, instead of relying on this behavior,
let's configure the iATU correctly.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The QSEE (trustzone) is started on IPQ4019 before Linux is started.
According to QCA, it is placed in in the the memory region
0x87e80000-0x88000000 and must not be accessed directly. There is an
additional memory region 0x87e00000-0x87E80000 smem which which can be used
for communication with the TZ. The driver for the latter is not yet ready
but it is still not allowed to use this memory region like any other
memory region.
Not reserving this memory region either leads to kernel crashes, kernel
hangs (often during the boot) or bus errors for userspace programs. The
latter happens when a program is using a memory region which is mapped to
these physical memory regions.
[ 571.758058] Unhandled fault: imprecise external abort (0xc06) at 0x01715ff8
[ 571.758099] pgd = cebec000
[ 571.763826] [01715ff8] *pgd=8e7fa835, *pte=87e7f75f, *ppte=87e7fc7f
Bus error
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
vbat_sns is needed to estimate a fairly accurate on chip voltage
and bat_therm is needed to produce an accurate percentage
from the estimated ocv.
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch marks all the gsbi i2c node at soc level dtsi, so that kernel
would not assume that its enabled and result in pin conflicts when gsbi
is used for UART or SPI.
Without this patch we see below pin conflict.
apq8064-pinctrl 800000.pinctrl: pin GPIO_20 already requested by
12450000.serial; cannot claim for 12460000.i2c
apq8064-pinctrl 800000.pinctrl: pin-20 (12460000.i2c) status -22
apq8064-pinctrl 800000.pinctrl: could not request pin 20 (GPIO_20)
from group gpio20 on device 800000.pinctrl
i2c_qup 12460000.i2c: Error applying setting, reverse things back
i2c_qup: probe of 12460000.i2c failed with error -22
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Device tree changes for omap variants for SDHCI
This series adds the devicetree configuration needed for pinctrl on
dra7 variants to use the SDHCI SDIO driver instead of mmc-omap-hs
driver. To use SDHCI, both the pins and the iodelay needs to be
configured.
This series is based on the related SDHCI drivers changes on a branch
set up by Ulf.
* tag 'omap-for-v4.18/dt-sdhci-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (28 commits)
Documentation: ARM: Add new MMC requirements for DRA7/K2G
ARM: dts: dra7: Add high speed modes capability to MMC1/MMC2 dt node
ARM: dts: dra7: Use sdhci-omap programming model
ARM: dts: dra76-evm: Add wilink8 wlan support
ARM: dts: dra7-evm: Add wilink8 wlan support
ARM: dts: dra7-evm: Model EVM_3V6 regulator
ARM: dts: dra72-evm-common: Add wilink8 wlan support
ARM: dts: am57xx-beagle-x15/am57xx-idk: Fix pinctrl-names
ARM: dts: am574x-idk: Add pinmux configuration for MMC
ARM: dts: dra71-evm: Use pinctrl group from dra7-mmc-iodelay.dtsi to select pulldown
ARM: dts: am57xx-idk: Use pinctrl group from dra7-mmc-iodelay.dtsi to select pulldown
ARM: dts: dra7-mmc-iodelay: Add a new pinctrl group for clk line without pullup
ARM: dts: dra71-evm: Add "vqmmc-supply" property for mmc2
ARM: dts: dra72-evm-common: Remove mmc specific pinmux
mmc: sdhci-omap: Get IODelay values for 3.3v DDR mode
dt-bindings: sdhci-omap: Add pinctrl bindings
mmc: sdhci-omap: Add sdhci_omap specific ops for enable_sdio_irq
mmc: sdhci-omap: Add support for MMC/SD controller in k2g SoC
dt-bindings: sdhci-omap: Add K2G specific binding
mmc: sdhci-omap: Workaround for Errata i834
...
Signed-off-by: Olof Johansson <olof@lixom.net>
