This fixes polarity of SD card write-protect pin on DA850 EVM
and fixes interrupt property for DA850 SoC GPIO as defined in
device-tree.
Both of these are not introduced with v4.18 merge but have
existed prior.
* tag 'davinci-fixes-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: Fix interrups property for gpio
ARM: davinci: board-da850-evm: fix WP pin polarity for MMC/SD
Signed-off-by: Olof Johansson <olof@lixom.net>
The intc #interrupt-cells is equal to 1. Currently gpio
node has 2 cells per IRQ which is wrong. Remove the additional
cell for each of the interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: 2e38b946dc ("ARM: davinci: da850: add GPIO DT node")
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
4.18, please pull the following:
- Ray fixes the I2C and PCIe interrupt types for the Cygnus SoC
- Florian fixes the I2C and PCIe interrupts for the Northstar
(BCM5301x), Northstar Plus and Hurricane 2 SoCs
* tag 'arm-soc/for-4.18/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: Cygnus: Fix PCIe controller interrupt type
ARM: dts: Cygnus: Fix I2C controller interrupt type
ARM: dts: BCM5301x: Fix i2c controller interrupt type
ARM: dts: HR2: Fix interrupt types for i2c and PCIe
ARM: dts: NSP: Fix PCIe controllers interrupt types
ARM: dts: NSP: Fix i2c controller interrupt type
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX fixes for 4.18:
- Fix i.MX6SX PCIe MSI interrupt number, so that MSI IRQs can be
properly propagated to the upstream interrupt controller.
- Fix GPCv2 MIPI/PCIe/USB_HSIC's PGC offset. The values in Reference
Manual are incorrect.
- Correct SDMA setting for i.MX6Q SPI5 device to fix the issue, that
the SPI controller RX FIFO was not empty after a DMA transfer, and
the driver gets stuck in the next PIO transfer when reading one word
more than expected.
* tag 'imx-fixes-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: fix irq for pcie bridge
soc: imx: gpcv2: correct PGC offset
ARM: dts: imx6q: Use correct SDMA script for SPI5 core
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu fixes for 4.17 (part 2)
- Use correct size for ICU nodes (irq controller) on Armada 7K/8K
- Fix "#cooling-cells" property's name on Synology DS116 (Armada 385)
* tag 'mvebu-fixes-4.17-2' of git://git.infradead.org/linux-mvebu:
arm: dts: armada: Fix "#cooling-cells" property's name
arm64: dts: marvell: fix CP110 ICU node size
Signed-off-by: Olof Johansson <olof@lixom.net>
Use the correct IRQ line for the MSI controller in the PCIe host
controller. Apparently a different IRQ line is used compared to other
i.MX6 variants. Without this change MSI IRQs aren't properly propagated
to the upstream interrupt controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: b1d17f68e5 ("ARM: dts: imx: add initial imx6sx device tree source")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix PCIe controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom
Cygnus SoC
Fixes: cd590b50a9 ("ARM: dts: enable PCIe support for Cygnus")
Fixes: f6b889358a ("ARM: dts: Enable MSI support for Broadcom Cygnus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c controller should be using IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: bb097e3e00 ("ARM: dts: BCM5301X: Add I2C support to the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c and PCIe controllers had an incorrect type which should have
been set to IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The interrupts for the PCIe controllers should all be of type
IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.
Fixes: d71eb94120 ("ARM: dts: NSP: Add MSI support on PCI")
Fixes: 522199029f ("ARM: dts: NSP: Fix PCIE DT issue")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c controller should use IRQ_TYPE_LEVEL_HIGH instead of
IRQ_TYPE_NONE.
Fixes: 0f9f27a36d ("ARM: dts: NSP: Add I2C support to the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
According to the reference manual the shp_2_mcu / mcu_2_shp
scripts must be used for devices connected through the SPBA.
This fixes an issue we saw with DMA transfers.
Sometimes the SPI controller RX FIFO was not empty after a DMA
transfer and the driver got stuck in the next PIO transfer when
it read one word more than expected.
commit dd4b487b32 ("ARM: dts: imx6: Use correct SDMA script
for SPI cores") is fixing the same issue but only for SPI1 - 4.
Fixes: 677940258d ("ARM: dts: imx6q: enable dma for ecspi5")
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull ARM SoC late updates from Olof Johansson:
"This is a branch with a few merge requests that either came in late,
or took a while longer for us to review and merge than usual and thus
cut it a bit close to the merge window. We stage them in a separate
branch and if things look good, we still send them up -- and that's
the case here.
This is mostly DT additions for Renesas platforms, adding IP block
descriptions for existing and new SoCs.
There are also some driver updates for Qualcomm platforms for SMEM/QMI
and GENI, which is their generalized serial protocol interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (186 commits)
soc: qcom: smem: introduce qcom_smem_virt_to_phys()
soc: qcom: qmi: fix a buffer sizing bug
MAINTAINERS: Update pattern for qcom_scm
soc: Unconditionally include qcom Makefile
soc: qcom: smem: check sooner in qcom_smem_set_global_partition()
soc: qcom: smem: fix qcom_smem_set_global_partition()
soc: qcom: smem: fix off-by-one error in qcom_smem_alloc_private()
soc: qcom: smem: byte swap values properly
soc: qcom: smem: return proper type for cached entry functions
soc: qcom: smem: fix first cache entry calculation
soc: qcom: cmd-db: Make endian-agnostic
drivers: qcom: add command DB driver
arm64: dts: renesas: salvator-common: Add ADV7482 support
ARM: dts: r8a7740: Add CEU1
ARM: dts: r8a7740: Add CEU0
arm64: dts: renesas: salvator-common: enable VIN
arm64: dts: renesas: r8a77970: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a77965: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7796: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7795-es1: add CSI-2 node
...
Pull ARM SoC device tree updates from Olof Johansson:
"As always, a large number of DT updates. Too many to enumerate them
all, but at a glance:
New SoCs introduced in this release:
- Amlogic:
+ Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some
set top boxes and other products.
- Mediatek:
+ MT7623A, which is a flavor of the MT7623 family with other
on-chip ethernet options.
- Qualcomm:
+ SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
(Cortex-A75/A55 derivative) SoC that's one of the current
high-end mobile SoCs.
It's great to see mainline support for it. So far, you can't do
much with it, since a lot of peripherals are not yet in the DTs
but driver support for USB, GPU and other pieces are starting to
trickle in. This might end up being a well-supported SoC
upstream if the momentum keeps up.
- Renesas:
+ R8A77990, a.k.a R-Car E3, a new automotive
entertainment-targeted SoC. Currently only one Cortex-A53 CPU is
enabled, we are eagerly awaiting more. So far, basic drivers
such as serial, gpios, PMU and ethernet are enabled.
+ R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
GPU. Same here, basic set of drivers such as serial, gpios and
ethernet enabled, and SMP support is also forthcoming.
- STMicroelectronics:
+ STM32F469, very similar tih STM32F429 but with display support
Enhancements to SoCs/platforms (DTS contents, some driver portions
might not be in yet):
- Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
- Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
- Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
- Marvell Berlin2CD: SMP support, thermal sensors
- Mediatek MT7623: Highspeed DMA, audio support
- Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
- Renesas: Watchdog and PMU support across many platforms
- Rockchip RK3399: USB3 OTG support
- Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
- STMicro STM32: Lots of peripherals added to STM32MP175C
- Uniphier: Ethernet support
New boards:
- Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
- Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
- Allwinner A33: Nintendo NES/SuperNES Classic Edition
- Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
- Berlin2CD: Valve Steam Link
- Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
- Broadcom: Raspberry Pi 3 B+
- Mediatek MT7623N and MT7623A: reference boards
- Meson 8M2: Tronsmart MXIII Plus
- NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
- Qualcomm MSM8974: Sony Xperia Z1 Compact support
- Qualcomm SDM845: MTP development board
- Renesas: Ebisu R8A77990 board
- Renesas RZ/G1C: iwg23s: iWave G235-SDB
- TI am335x: Pocketbeagle support"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (448 commits)
ARM: dts: aspeed: Fix hwrng register address
arm64: dts: sprd: whale2: Add the rtc enable clock for watchdog
arm64: dts: sprd: Add GPIO and GPIO keys device nodes
arm64: dts: sprd: fix typo in 'remote-endpoint'
arm64: dts: apq8096-db820c: Removed bt-en-1-8v regulator
arm64: dts: fix regulator property name for wlan pcie endpoint
arm64: dts: qcom: msm8996: Use UFS_GDSC for UFS
ARM: dts: pxa3xx: fix MMC clocks
ARM: pxa: dts: add pin definitions for extended GPIOs
ARM: pxa: dts: add gpio-ranges to gpio controller
ARM: dts: ipq8074: Enable few peripherals for hk01 board
ARM: dts: ipq8074: Add pcie nodes
ARM: dts: ipq8074: Add peripheral nodes
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c2 board file
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk07.1 common data
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk04.1-c3 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.dtsi
ARM: dts: ipq4019: Change the max opp frequency
...
Pull clk updates from Stephen Boyd:
"This time we have a good set of changes to the core framework that do
some general cleanups, but nothing too major. The majority of the diff
goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is
introduced for Actions Semi so it takes up some lines to add all the
different types, and the Qualcomm diff is there because we add support
for two SoCs and it's quite a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic
platforms. And then the long tail of driver updates for various fixes
and stuff follows after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
clk: qcom: Export clk_fabia_pll_configure()
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
clk-si544: Properly round requested frequency to nearest match
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
clk: use match_string() helper
clk: bcm2835: use match_string() helper
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
clk: imx6: add EPIT clock support
clk: mvebu: use correct bit for 98DX3236 NAND
...
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver update for 4.18-rc1.
There's nothing major here, just lots of serial driver updates. Full
details are in the shortlog, nothing anything specific to call out
here.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (55 commits)
vt: Perform safe console erase only once
serial: imx: disable UCR4_OREN on shutdown
serial: imx: drop CTS/RTS handling from shutdown
tty: fix typo in ASYNCB_FOURPORT comment
serial: samsung: check DMA engine capabilities before using DMA mode
tty: Fix data race in tty_insert_flip_string_fixed_flag
tty: serial: msm_geni_serial: Fix TX infinite loop
serial: 8250_dw: Fix runtime PM handling
serial: 8250: omap: Fix idling of clocks for unused uarts
tty: serial: drop ATH79 specific SoC symbols
serial: 8250: Add missing rxtrig_bytes on Altera 16550 UART
serial/aspeed-vuart: fix a couple mod_timer() calls
serial: sh-sci: Use spin_{try}lock_irqsave instead of open coding version
serial: 8250_of: Add IO space support
tty/serial: atmel: use port->name as name in request_irq()
serial: imx: dma_unmap_sg buffers on shutdown
serial: imx: cleanup imx_uart_disable_dma()
tty: serial: qcom_geni_serial: Add early console support
tty: serial: qcom_geni_serial: Return IRQ_NONE for spurious interrupts
tty: serial: qcom_geni_serial: Use iowrite32_rep to write to FIFO
...
Pull irq updates from Thomas Gleixner:
- Consolidation of softirq pending:
The softirq mask and its accessors/mutators have many implementations
scattered around many architectures. Most do the same things
consisting in a field in a per-cpu struct (often irq_cpustat_t)
accessed through per-cpu ops. We can provide instead a generic
efficient version that most of them can use. In fact s390 is the only
exception because the field is stored in lowcore.
- Support for level!?! triggered MSI (ARM)
Over the past couple of years, we've seen some SoCs coming up with
ways of signalling level interrupts using a new flavor of MSIs, where
the MSI controller uses two distinct messages: one that raises a
virtual line, and one that lowers it. The target MSI controller is in
charge of maintaining the state of the line.
This allows for a much simplified HW signal routing (no need to have
hundreds of discrete lines to signal level interrupts if you already
have a memory bus), but results in a departure from the current idea
the kernel has of MSIs.
- Support for Meson-AXG GPIO irqchip
- Large stm32 irqchip rework (suspend/resume, hierarchical domains)
- More SPDX conversions
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
ARM: dts: stm32: Add exti support to stm32mp157 pinctrl
ARM: dts: stm32: Add exti support for stm32mp157c
pinctrl/stm32: Add irq_eoi for stm32gpio irqchip
irqchip/stm32: Add suspend/resume support for hierarchy domain
irqchip/stm32: Add stm32mp1 support with hierarchy domain
irqchip/stm32: Prepare common functions
irqchip/stm32: Add host and driver data structures
irqchip/stm32: Add suspend support
irqchip/stm32: Add falling pending register support
irqchip/stm32: Checkpatch fix
irqchip/stm32: Optimizes and cleans up stm32-exti irq_domain
irqchip/meson-gpio: Add support for Meson-AXG SoCs
dt-bindings: interrupt-controller: New binding for Meson-AXG SoC
dt-bindings: interrupt-controller: Fix the double quotes
softirq/s390: Move default mutators of overwritten softirq mask to s390
softirq/x86: Switch to generic local_softirq_pending() implementation
softirq/sparc: Switch to generic local_softirq_pending() implementation
softirq/powerpc: Switch to generic local_softirq_pending() implementation
softirq/parisc: Switch to generic local_softirq_pending() implementation
softirq/ia64: Switch to generic local_softirq_pending() implementation
...
The register address should be the full address of the rng, not the
offset from the start of the SCU.
Fixes: 5daa8212c0 ("ARM: dts: aspeed: Describe random number device")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
ENET "ipg" clock should be IMX7D_ENETx_IPG_ROOT_CLK
rather than IMX7D_ENET_AXI_ROOT_CLK which is for ENET bus
clock.
Based on Andy Duan's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
AT91 DT for 4.18:
- small DT improvements without functional changes
* tag 'at91-ab-4.18-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91-sama5d2_xplained: Use IRQ_TYPE specifier
ARM: dts: at91: sama5d4ek: use canonical compatible for touchscreen
Signed-off-by: Olof Johansson <olof@lixom.net>
ASPEED device tree updates for 4.18
New hardware support added:
USB controllers for AST2400 and AST2500 which have drivers
merged in 4.18.
Hardware random number generator which we made enhancements to many
releases ago, but never added the device tree parts.
Misc changes to support watchdog and gpio-keys features used by
OpenBMC systems.
New machines:
Intel S2600WF, an Intel platform family with an ASPEED AST2500 BMC.
Inventec Lanyang, a Power 9 platform with AST2500.
Portwell Neptune, a x86 server development kit with an AST2500.
* tag 'aspeed-4.18-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: Aspeed: Enable USB ports on eval board.
ARM: dts: Add Aspeed SoC USB controllers to device-tree
ARM: dts: aspeed: Add S2600WF BMC Machine
ARM: dts: aspeed: Add Inventec Lanyang BMC
ARM: dts: aspeed: Add Portwell Neptune machine
ARM: dts: aspeed: witherspoon: Set alternate boot
ARM: dts: aspeed: witherspoon: Add gpio keys for power supply presence
ARM: dts: aspeed: witherspoon: Enable checkstop and cooling gpio keys
ARM: dts: aspeed: zaius: Add pcie-e2b-present gpio key
ARM: dts: aspeed: romulus: Add id-button gpio key
ARM: dts: aspeed: Describe random number device
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner fixes for 4.17
Here is a bunch of fixes for merge issues, typos and wrong clocks being
described for simplefb, resulting in non-working displays.
* tag 'sunxi-fixes-for-4.17' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sun8i: v3s: fix spelling mistake: "disbaled" -> "disabled"
ARM: dts: sun4i: Fix incorrect clocks for displays
ARM: dts: sun8i: h3: Re-enable EMAC on Orange Pi One
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung DTS ARM changes for v4.18, part 2
1. Add support for audio over HDMI for Odroid X/X2/U3.
* tag 'samsung-dt-4.18-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add support for audio over HDMI for Odroid X/X2/U3
Signed-off-by: Olof Johansson <olof@lixom.net>
berlin DT changes for v4.18
* tag 'berlin-dt-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin:
ARM: dts: berlin2q: move PMU node from soc to root
ARM: dts: berlin*-dts: use SPDX-License-Identifier for berlin based board
ARM: dts: berlin*.dtsi: use SPDX-License-Identifier for berlin SoCs
ARM: dts: berlin2: fix irq type for arm twd timer
ARM: dts: berlin2q: fix irq type for arm twd timer
ARM: dts: berlin2q: add "cache-unified" to l2 node
ARM: dts: berlin2q: add interrupt-affinity to pmu node
ARM: dts: chromecast: use PWM for LEDs
ARM: dts: chromecast: override bad bootloader memory info
ARM: dts: berlin2cd: add Valve Steam Link board
ARM: dts: berlin2cd: add a label for the CPU node
ARM: dts: berlin2cd: add remaining nodes to apb subtrees
ARM: dts: berlin2cd: add remaining Cortex-A9 nodes
ARM: dts: berlin2cd: add ADC/thermal sensor node
ARM: dts: berlin2cd: move PMU node from soc to root
ARM: dts: berlin2cd: fix local timer interrupt flags
Signed-off-by: Olof Johansson <olof@lixom.net>
Amlogic 32-bit DT changes for v4.18, round 2
- remove MACH_MESON8B, only used for building DTs
* tag 'amlogic-dt-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: meson: merge Kconfig symbol MACH_MESON8B into MACH_MESON8
ARM: dts: meson: build the Meson8b .dtbs with MACH_MESON8
Signed-off-by: Olof Johansson <olof@lixom.net>
Qualcomm Device Tree Changes for v4.18
* APQ8064 fixes for irq translations and pci address translation
* Fix RPM clock controller compatible on MSM8660
* Add TZ and SMEM reserved regions on IPQ4019
* Add vadc nodes for PM8941
* Disable i2c by default at top level APQ8064 dtsi
* tag 'qcom-dts-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: dts: qcom-apq8064: use correct pci address for address translation
ARM: dts: qcom-apq8064: fix gic_irq_domain_translate warnings
ARM: dts: Fix the RPM clock controller compatible string
ARM: dts: ipq4019: Add TZ and SMEM reserved regions
ARM: dts: qcom: pm8941: Add vadc nodes needed to estimate an ocv
ARM: dts: qcom-apq8064: disable i2c by default at soc dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
The clocks for the 3 MMC controllers on pxa3xx platforms are CLK_MMC1,
CLK_MMC2 and CLK_MMC3. CLK_MMC is only for pxa2xx.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The PXA3xx series features some extended GPIO banks which are named GPIO0_2,
GPIO1_2 etc. The PXA300, PXA310 and PXA320 have different numbers of such
pins, and they also have variant-specific register offsets.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The PXA GPIO driver calls out to the pinctrl driver for claiming pins
unless the config has CONFIG_PINCTRL unset. IOW, if a pinctrl driver is
active, it must be visible to the GPIO driver.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Second set of dts changes for omap variants for v4.18 merge window
This series of changes contains fixes for already queued tps65218
IRQ_TYPE, and fixes for omap3 and am335x use of IRQ_TYPE. There are
also addition of oscillator clock for logicpd omap3 boards and a series
of changes to improve support for am3517-evm board. And there is also
a change to configure WLAN for am437x-sk-evm.
* tag 'omap-for-v4.18/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (24 commits)
ARM: dts: am3517-evm: Add User LEDs and Pushbutton
ARM: dts: am3517-evm: Add I/O expander for User DIP switches and LEDS
ARM: dts: logicpd-som-lv: Fix Touchscreen controller
ARM: dts: am3517-som: Add Seiko Instruments RTC s35390a
ARM: dts: am437x-sk-evm: add wilink8 support
ARM: dts: am3517-evm: Add LCD panel type 15 support
ARM: dts: am3517-som: Associate cpu to regulator supply
ARM: dts: am3517-som: Add TI TPS65023 regulators
ARM: dts: am3517-evm: Split off SOM features from baseboard
ARM: dts: am3517: Add pinmuxing, CD and WP for MMC1
ARM: dts: logicpd-som-lv: Add fixed 26MHz clock as fck for twl
ARM: dts: logicpd-torpedo: Add fixed 26MHz clock as fck for twl
ARM: dts: omap3-pandora-common: Use IRQ_TYPE specifier
ARM: dts: am335x-boneblue: Use IRQ_TYPE specifier
ARM: dts: am335x-baltos.dtsi: Use IRQ_TYPE specifier
ARM: dts: am335x-baltos-ir5221: Use IRQ_TYPE specifier
ARM: dts: am335x-baltos-ir3220: Use IRQ_TYPE specifier
Revert "ARM: dts: am437x-sk-evm: Correct tps65218 irq type"
ARM: dts: am437x-epos-evm: Fixup (again) tps65218 irq type
ARM: dts: am437x-cm-t43: Fixup (again) tps65218 irq type
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner H3/H5 support for 4.18
Here is our usual bunch of changes for the H3 and H5 SoCs that share the
same SoC design but with different CPUs.
This time, most of the changes are about supporting CPUFreq on these SoCs,
with voltage scaling being enabled for a number of boards.
* tag 'sunxi-h3-h5-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: h3: Add SY8106A regulator to Orange Pi PC
arm64: dts: allwinner: Add dts file for Libre Computer Board ALL-H3-CC H5 ver.
arm64: dts: allwinner: Sort dtb entries in Makefile
arm64: dts: allwinner: h5: Add cpu0 label for first cpu
ARM: dts: sun8i: h2+: Add Libre Computer Board ALL-H3-CC H2+ ver.
ARM: dts: sun8i: h2-plus: Sort dtb entries in Makefile
arm: dts: sun8i: h3: libretech-all-h3-cc: Move board definition to common dtsi
ARM: dts: sun8i: h3: fix ALL-H3-CC H3 ver VCC-1V2 regulator voltage
ARM: dts: sun8i: h3: set the cpu-supply to VDD-CPUX on ALL-H3-CC H3 ver
ARM: dts: sun8i: h3: fix ALL-H3-CC H3 ver VDD-CPUX voltage
ARM: dts: sun8i: h3: add SY8113B regulator used by Orange Pi One board
ARM: dts: sun8i: h2+: add SY8113B regulator used by Orange Pi Zero board
ARM: dts: sun8i: h3: add operating-points-v2 table for CPU
ARM: dts: sunxi: h3/h5: Add r_i2c I2C controller
ARM: dts: sunxi: h3/h5: Add r_i2c pinmux node
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner DT additions for 4.18
Here is our usual bunch of DT changes for our arm SoCs, with most
significantly:
- MIPI-DSI support for the A33
- NAND support for the A33
- SMP support for the A83t
- GMAC support for the R40
- And some new boards: Olimex A20-SOM-EVB-eMMC, Nintendo NES and SuperNES
Classic
* tag 'sunxi-dt-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Add Olimex A20-SOM-EVB-eMMC board
ARM: dts: sun8i: r40: bananapi-m2-ultra: Enable GMAC ethernet controller
ARM: dts: sun8i: r40: Add device node and RGMII pinmux node for GMAC
ARM: dts: sun8i: r40: bananapi-m2-ultra: Sort device node dereferences
ARM: dts: sun8i: Add enable-method for SMP support for the A83T SoC
ARM: dts: sun8i: a83t: Add CCI-400 node
ARM: dts: sun8i: Add R_CPUCFG device node for the A83T dtsi
ARM: dts: sun8i: Add CPUCFG device node for A83T dtsi
ARM: dts: nes: add Nintendo NES/SuperNES Classic Edition support
ARM: dts: sun8i: a23/a33: declare NAND pins
ARM: dts: sunxi: Add sid for a83t
ARM: dts: sun8i: a33: Add the DSI-related nodes
ARM: dts: sunxi: Change sun7i-a20-olimex-som204-evb to not use cd-inverted
ARM: sun8i: v40: enable USB host ports for Banana Pi M2 Berry
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX device tree update for 4.18:
- New boards support: BTicino i.MX6DL Mamoj board, DHCOM iMX6 SoM and
PDK2 board, Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit,
Kieback & Peter GmbH iMX6Q TPC board.
- A series from Anson Huang to add a bunch of devices for i.MX6SX
SabreAuto board, PMIC, IO expanders, FEC, Watchdog, LED and Touch.
- Update i.MX7D for cpufreq support, using operating-points-v2
bindings, correcting cpu supply name for voltage scaling.
- Clean up unneeded 'codec-handle' property from imx25-pdk and
imx53-tx53 device tree.
- Switch SoC dtsi and NXP board dts files to use SPDX identifier.
- Remove unnecessary '#address-cells/#size-cells' to fix DTC warning
avoid_unnecessary_addr_size seen with W=1 switch.
- A series from Rob Herring to fix DTC warning graph_endpoint seen with
IPU OF graph when W=1 switch is on.
- Update a few boards to use symbol name instead of hard-coding the
input codes.
- Update a number of boards to use IRQ_TYPE specifier instead of the
raw value.
- A few updates for i.MX6 RDU2 board: bumping SoC/PU operating points,
adding assigned clocks for GPU, and enabling eGalax touchscreen.
- A couple of i.MX51 RDU1 updates: limiting usbh1 to full-speed, and
cleaning up eMMC device node.
- Convert Hummingboard audio bindings from imx-audio-sgtl5000 to
simple-audio-card, so that auxiliary audio devices such as external
amplifiers can be supported.
- Replace underscore with hyphen in aliases name to fix DTC warning
alias_paths with W=1 switch.
- A couple of updates on i.MX7D SAI and i.MX6ULL UART5 pin defines.
- Other random and small changes.
* tag 'imx-dt-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (72 commits)
ARM: dts: imx28/imx53: enable edt-ft5x06 wakeup source
ARM: dts: imx51-zii-rdu1: cleanup eMMC node
ARM: dts: vf610-zii-dev: enable vf610 builtin temp sensor
ARM: dts: imx7d: use operating-points-v2 for cpu
ARM: dts: imx7s-warp: remove unnecessary cpu regulator supply
ARM: dts: imx7d: correct cpu supply name for voltage scaling
ARM: dts: imx51-zii-rdu1: limit usbh1 to full-speed
ARM: dts: imx6/7: Remove unit-address from anatop regulators
ARM: dts: imx: Switch NXP boards to SPDX identifier
ARM: dts: imx6qdl-phytec-pfla02: Use IRQ_TYPE specifier
ARM: dts: imx53-voipac-dmm-668: Use IRQ_TYPE specifier
ARM: dts: imx53-qsb: Use IRQ_TYPE specifier
ARM: dts: vf-colibri-eval-v3: Use IRQ_TYPE specifier
ARM: dts: imx6q-gk802: Do not hardcode input codes
ARM: dts: imx53-smd: Do not hardcode input codes
ARM: dts: imx53-ard: Do not hardcode input codes
ARM: dts: imx7: Fix error in coresight TPIU graph connection
ARM: dts: imx53: Fix LDB OF graph warning
ARM: dts: imx: fix IPU OF graph endpoint node names
ARM: dts: imx: Switch to SPDX identifier
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Now with the driver updates for some peripherals being there,
add i2c, spi, pcie, bam, qpic-nand, scm nodes to enhance the available
peripheral support.
Reviewed-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
