In NVMe's error handler, follows the typical steps of tearing down
hardware for recovering controller:
1) stop blk_mq hw queues
2) stop the real hw queues
3) cancel in-flight requests via
blk_mq_tagset_busy_iter(tags, cancel_request, ...)
cancel_request():
mark the request as abort
blk_mq_complete_request(req);
4) destroy real hw queues
However, there may be race between #3 and #4, because blk_mq_complete_request()
may run q->mq_ops->complete(rq) remotelly and asynchronously, and
->complete(rq) may be run after #4.
This patch introduces blk_mq_complete_request_sync() for fixing the
above race.
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: James Smart <james.smart@broadcom.com>
Cc: linux-nvme@lists.infradead.org
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For an uncontended rwsem, count and owner are the only fields a task
needs to touch when acquiring the rwsem. So they are put next to each
other to increase the chance that they will share the same cacheline.
On a ThunderX2 99xx (arm64) system with 32K L1 cache and 256K L2
cache, a rwsem locking microbenchmark with one locking thread was
run to write-lock and write-unlock an array of rwsems separated 2
cachelines apart in a 1M byte memory block. The locking rates (kops/s)
of the microbenchmark when the rwsems are at various "long" (8-byte)
offsets from beginning of the cacheline before and after the patch were
as follows:
Cacheline Offset Pre-patch Post-patch
---------------- --------- ----------
0 17,449 16,588
1 17,450 16,465
2 17,450 16,460
3 17,453 16,462
4 14,867 16,471
5 14,867 16,470
6 14,853 16,464
7 14,867 13,172
Before the patch, the count and owner are 4 "long"s apart. After the
patch, they are only 1 "long" apart.
The rwsem data have to be loaded from the L3 cache for each access. It
can be seen that the locking rates are more consistent after the patch
than before. Note that for this particular system, the performance
drop happens whenever the count and owner are at an odd multiples of
"long"s apart. No performance drop was observed when only a single rwsem
was used (hot cache). So the drop is likely just an idiosyncrasy of the
cache architecture of this chip than an inherent problem with the patch.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Waiman Long <longman@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/20190404174320.22416-12-longman@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch introduces a new helper routine in the OPP core, which
returns the OPP with the highest frequency which has voltage less than
or equal to the target voltage passed to the helper.
Signed-off-by: Andrew-sh.Cheng <andrew-sh.cheng@mediatek.com>
[ Viresh: Massaged the commit log and renamed the helper with some
cleanups. ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Create a new prio in the FDB, it will be used when inserting steering rules
into the FDB from the RDMA side. We create a new PRIO so rules from the
net side and rules from the RDMA side won't be inserted to the same PRIO,
each side has it's own sandbox to play in.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
When creating the FDB prios, use the enum values already defined and not
the hardcoded values.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Given we'll be reusing BPF array maps for global data/bss/rodata
sections, we need a way to associate BTF DataSec type as its map
value type. In usual cases we have this ugly BPF_ANNOTATE_KV_PAIR()
macro hack e.g. via 38d5d3b3d5 ("bpf: Introduce BPF_ANNOTATE_KV_PAIR")
to get initial map to type association going. While more use cases
for it are discouraged, this also won't work for global data since
the use of array map is a BPF loader detail and therefore unknown
at compilation time. For array maps with just a single entry we make
an exception in terms of BTF in that key type is declared optional
if value type is of DataSec type. The latter LLVM is guaranteed to
emit and it also aligns with how we regard global data maps as just
a plain buffer area reusing existing map facilities for allowing
things like introspection with existing tools.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch adds a new BPF_MAP_FREEZE command which allows to
"freeze" the map globally as read-only / immutable from syscall
side.
Map permission handling has been refactored into map_get_sys_perms()
and drops FMODE_CAN_WRITE in case of locked map. Main use case is
to allow for setting up .rodata sections from the BPF ELF which
are loaded into the kernel, meaning BPF loader first allocates
map, sets up map value by copying .rodata section into it and once
complete, it calls BPF_MAP_FREEZE on the map fd to prevent further
modifications.
Right now BPF_MAP_FREEZE only takes map fd as argument while remaining
bpf_attr members are required to be zero. I didn't add write-only
locking here as counterpart since I don't have a concrete use-case
for it on my side, and I think it makes probably more sense to wait
once there is actually one. In that case bpf_attr can be extended
as usual with a flag field and/or others where flag 0 means that
we lock the map read-only hence this doesn't prevent to add further
extensions to BPF_MAP_FREEZE upon need.
A map creation flag like BPF_F_WRONCE was not considered for couple
of reasons: i) in case of a generic implementation, a map can consist
of more than just one element, thus there could be multiple map
updates needed to set the map into a state where it can then be
made immutable, ii) WRONCE indicates exact one-time write before
it is then set immutable. A generic implementation would set a bit
atomically on map update entry (if unset), indicating that every
subsequent update from then onwards will need to bail out there.
However, map updates can fail, so upon failure that flag would need
to be unset again and the update attempt would need to be repeated
for it to be eventually made immutable. While this can be made
race-free, this approach feels less clean and in combination with
reason i), it's not generic enough. A dedicated BPF_MAP_FREEZE
command directly sets the flag and caller has the guarantee that
map is immutable from syscall side upon successful return for any
future syscall invocations that would alter the map state, which
is also more intuitive from an API point of view. A command name
such as BPF_MAP_LOCK has been avoided as it's too close with BPF
map spin locks (which already has BPF_F_LOCK flag). BPF_MAP_FREEZE
is so far only enabled for privileged users.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This work adds two new map creation flags BPF_F_RDONLY_PROG
and BPF_F_WRONLY_PROG in order to allow for read-only or
write-only BPF maps from a BPF program side.
Today we have BPF_F_RDONLY and BPF_F_WRONLY, but this only
applies to system call side, meaning the BPF program has full
read/write access to the map as usual while bpf(2) calls with
map fd can either only read or write into the map depending
on the flags. BPF_F_RDONLY_PROG and BPF_F_WRONLY_PROG allows
for the exact opposite such that verifier is going to reject
program loads if write into a read-only map or a read into a
write-only map is detected. For read-only map case also some
helpers are forbidden for programs that would alter the map
state such as map deletion, update, etc. As opposed to the two
BPF_F_RDONLY / BPF_F_WRONLY flags, BPF_F_RDONLY_PROG as well
as BPF_F_WRONLY_PROG really do correspond to the map lifetime.
We've enabled this generic map extension to various non-special
maps holding normal user data: array, hash, lru, lpm, local
storage, queue and stack. Further generic map types could be
followed up in future depending on use-case. Main use case
here is to forbid writes into .rodata map values from verifier
side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This generic extension to BPF maps allows for directly loading
an address residing inside a BPF map value as a single BPF
ldimm64 instruction!
The idea is similar to what BPF_PSEUDO_MAP_FD does today, which
is a special src_reg flag for ldimm64 instruction that indicates
that inside the first part of the double insns's imm field is a
file descriptor which the verifier then replaces as a full 64bit
address of the map into both imm parts. For the newly added
BPF_PSEUDO_MAP_VALUE src_reg flag, the idea is the following:
the first part of the double insns's imm field is again a file
descriptor corresponding to the map, and the second part of the
imm field is an offset into the value. The verifier will then
replace both imm parts with an address that points into the BPF
map value at the given value offset for maps that support this
operation. Currently supported is array map with single entry.
It is possible to support more than just single map element by
reusing both 16bit off fields of the insns as a map index, so
full array map lookup could be expressed that way. It hasn't
been implemented here due to lack of concrete use case, but
could easily be done so in future in a compatible way, since
both off fields right now have to be 0 and would correctly
denote a map index 0.
The BPF_PSEUDO_MAP_VALUE is a distinct flag as otherwise with
BPF_PSEUDO_MAP_FD we could not differ offset 0 between load of
map pointer versus load of map's value at offset 0, and changing
BPF_PSEUDO_MAP_FD's encoding into off by one to differ between
regular map pointer and map value pointer would add unnecessary
complexity and increases barrier for debugability thus less
suitable. Using the second part of the imm field as an offset
into the value does /not/ come with limitations since maximum
possible value size is in u32 universe anyway.
This optimization allows for efficiently retrieving an address
to a map value memory area without having to issue a helper call
which needs to prepare registers according to calling convention,
etc, without needing the extra NULL test, and without having to
add the offset in an additional instruction to the value base
pointer. The verifier then treats the destination register as
PTR_TO_MAP_VALUE with constant reg->off from the user passed
offset from the second imm field, and guarantees that this is
within bounds of the map value. Any subsequent operations are
normally treated as typical map value handling without anything
extra needed from verification side.
The two map operations for direct value access have been added to
array map for now. In future other types could be supported as
well depending on the use case. The main use case for this commit
is to allow for BPF loader support for global variables that
reside in .data/.rodata/.bss sections such that we can directly
load the address of them with minimal additional infrastructure
required. Loader support has been added in subsequent commits for
libbpf library.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
No modular uses since introducion of alloc_file_pseudo(),
and the only non-modular user not in alloc_file_pseudo()
had actually been wrong - should've been d_alloc_anon().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
For lockless accesses to dentries we don't have pinned we rely
(among other things) upon having an RCU delay between dropping
the last reference and actually freeing the memory.
On the other hand, for things like pipes and sockets we neither
do that kind of lockless access, nor want to deal with the
overhead of an RCU delay every time a socket gets closed.
So delay was made optional - setting DCACHE_RCUACCESS in ->d_flags
made sure it would happen. We tried to avoid setting it unless
we knew we need it. Unfortunately, that had led to recurring
class of bugs, in which we missed the need to set it.
We only really need it for dentries that are created by
d_alloc_pseudo(), so let's not bother with trying to be smart -
just make having an RCU delay the default. The ones that do
*not* get it set the replacement flag (DCACHE_NORCU) and we'd
better use that sparingly. d_alloc_pseudo() is the only
such user right now.
FWIW, the race that finally prompted that switch had been
between __lock_parent() of immediate subdirectory of what's
currently the root of a disconnected tree (e.g. from
open-by-handle in progress) racing with d_splice_alias()
elsewhere picking another alias for the same inode, either
on outright corrupted fs image, or (in case of open-by-handle
on NFS) that subdirectory having been just moved on server.
It's not easy to hit, so the sky is not falling, but that's
not the first race on similar missed cases and the logics
for settinf DCACHE_RCUACCESS has gotten ridiculously
convoluted.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
To be able to predict the sleep duration for a CPU entering idle, it
is essential to know the expiration time of the next timer. Both the
teo and the menu cpuidle governors already use this information for
CPU idle state selection.
Moving forward, a similar prediction needs to be made for a group of
idle CPUs rather than for a single one and the following changes
implement a new genpd governor for that purpose.
In order to support that feature, add a new function called
tick_nohz_get_next_hrtimer() that will return the next hrtimer
expiration time of a given CPU to be invoked after deciding
whether or not to stop the scheduler tick on that CPU.
Make the cpuidle core call tick_nohz_get_next_hrtimer() right
before invoking the ->enter() callback provided by the cpuidle
driver for the given state and store its return value in the
per-CPU struct cpuidle_device, so as to make it available to code
outside of cpuidle.
Note that at the point when cpuidle calls tick_nohz_get_next_hrtimer(),
the governor's ->select() callback has already returned and indicated
whether or not the tick should be stopped, so in fact the value
returned by tick_nohz_get_next_hrtimer() always is the next hrtimer
expiration time for the given CPU, possibly including the tick (if
it hasn't been stopped).
Co-developed-by: Lina Iyer <lina.iyer@linaro.org>
Co-developed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To enable a CPU device to be attached to a PM domain managed by genpd,
make a few changes to it for convenience.
To be able to quickly find out what CPUs are attached to a genpd,
which typically becomes useful from a genpd governor as subsequent
changes are about to show, add a cpumask to struct generic_pm_domain
to be updated when a CPU device gets attached to the genpd containing
that cpumask. Also, propagate the cpumask changes upwards in the
domain hierarchy to the master PM domains. This way, the cpumask for
a genpd hierarchically reflects all CPUs attached to the topology
below it.
Finally, make this an opt-in feature, to avoid having to manage CPUs
and the cpumask for a genpd that don't need it. To that end, add
a new genpd configuration bit, GENPD_FLAG_CPU_DOMAIN.
Co-developed-by: Lina Iyer <lina.iyer@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a data pointer to the genpd_power_state struct, to allow a genpd
backend driver to store per-state specific data. To introduce the
pointer, change the way genpd deals with freeing of the corresponding
allocated data.
More precisely, clarify the responsibility of whom that shall free the
data, by adding a ->free_states() callback to the generic_pm_domain
structure. The one allocating the data will be expected to set the
callback, to allow genpd to invoke it from genpd_remove().
Co-developed-by: Lina Iyer <lina.iyer@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sphinx emits various warnings all caused by a missing colon before code
block:
WARNING: Block quote ends without a blank line; unexpected unindent.
ERROR: Unexpected indentation.
WARNING: Block quote ends without a blank line; unexpected unindent.
Add the colon, clearing sphinx warnings.
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
In certain situations, such as when returning from low power modes, the
EMIF must re-run hardware leveling to properly restore DDR3 access.
This is accomplished by introducing a new ti-emif-sram-pm call,
ti_emif_run_hw_leveling, to check if DDR3 is in use and if so, trigger
the full write and read leveling processes.
Suggested-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We have a function to copy strings safely and we have a function to copy
strings and zero the tail of the destination (if source string is
shorter than destination buffer) but we do not have a function to do
both at once. This means developers must write this themselves if they
desire this functionality. This is a chore, and also leaves us open to
off by one errors unnecessarily.
Add a function that calls strscpy() then memset()s the tail to zero if
the source string is shorter than the destination buffer.
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tobin C. Harding <tobin@kernel.org>
Signed-off-by: Shuah Khan <shuah@kernel.org>
genphy_read_status() so far checks phydev->supported, not the actual
PHY capabilities. This can make a difference if the supported speeds
have been limited by of_set_phy_supported() or phy_set_max_speed().
It seems that this issue only affects the link partner advertisements
as displayed by ethtool. Also this patch wouldn't apply to older
kernels because linkmode bitmaps have been introduced recently.
Therefore net-next.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mamameed says:
====================
mlx5-updates-2019-04-02
This series provides misc updates to mlx5 driver
1) Aya Levin (1): Handle event of power detection in the PCIE slot
2) Eli Britstein (6):
Some TC VLAN related updates and fixes to the previous VLAN modify action
support patchset.
Offload TC e-switch rules with egress/ingress VLAN devices
3) Max Gurtovoy (1): Fix double mutex initialization in esiwtch.c
4) Tariq Toukan (3): Misc small updates
A write memory barrier is sufficient in EQ ci update
Obsolete param field holding a constant value
Unify logic of MTU boundaries
5) Tonghao Zhang (4): Misc updates to en_tc.c
Make the log friendly when decapsulation offload not supported
Remove 'parse_attr' argument in parse_tc_fdb_actions()
Deletes unnecessary setting of esw_attr->parse_attr
Return -EOPNOTSUPP when attempting to offload an unsupported action
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add version option support to the nftables "osf" expression.
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
vring_create_virtqueue() allows the caller to specify via the
may_reduce_num parameter whether the vring code is allowed to
allocate a smaller ring than specified.
However, the split ring allocation code tries to allocate a
smaller ring on allocation failure regardless of what the
caller specified. This may cause trouble for e.g. virtio-pci
in legacy mode, which does not support ring resizing. (The
packed ring code does not resize in any case.)
Let's fix this by bailing out immediately in the split ring code
if the requested size cannot be allocated and may_reduce_num has
not been specified.
While at it, fix a typo in the usage instructions.
Fixes: 2a2d1382fe ("virtio: Add improved queue allocation API")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Jens Freimann <jfreimann@redhat.com>
NF_NAT_NEEDED is true whenever nat support for either ipv4 or ipv6 is
enabled. Now that the af-specific nat configuration switches have been
removed, IS_ENABLED(CONFIG_NF_NAT) has the same effect.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
very little code, so it really doesn't make sense to have extra
modules or even a kconfig knob for this.
Merge them and make functionality available unconditionally.
The merge makes inet family route support trivial, so add it
as well here.
Before:
text data bss dec hex filename
835 832 0 1667 683 nft_chain_route_ipv4.ko
870 832 0 1702 6a6 nft_chain_route_ipv6.ko
111568 2556 529 114653 1bfdd nf_tables.ko
After:
text data bss dec hex filename
113133 2556 529 116218 1c5fa nf_tables.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
there is a similar helper in net/netfilter/nf_tables_api.c,
this maybe become a common request someday, so move it to
time.c
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add support for rtc+ddr in self refresh mode. Add addtional
pm hooks for save/restore and rtc suspend/resume.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prepare rtc driver for rtc-only with DDR in self-refresh mode.
omap_rtc_power_off now should cater to two features:
1) RTC plus DDR in self-refresh is power a saving mode where in the
entire system including the different voltage rails from PMIC are
shutdown except the ones feeding on to RTC and DDR. DDR is kept in
self-refresh hence the contents are preserved. RTC ALARM2 is connected
to PMIC_EN line once we the ALARM2 is triggered we enter the mode with
DDR in self-refresh and RTC Ticking. After a predetermined time an RTC
ALARM1 triggers waking up the system[1]. The control goes to bootloader.
The bootloader then checks RTC scratchpad registers to confirm it was an
rtc_only wakeup and follows a different path, configure bare minimal
clocks for ddr and then jumps to the resume address in another RTC
scratchpad registers and transfers the control to Kernel. Kernel then
restores the saved context. omap_rtc_power_off_program does the ALARM2
programming part.
[1] http://www.ti.com/lit/ug/spruhl7h/spruhl7h.pdf Page 2884
2) Power-off: This is usual poweroff mode. omap_rtc_power_off calls the
above omap_rtc_power_off_program function and in addition to that
programs the OMAP_RTC_PMIC_REG for any external wake ups for PMIC like
the pushbutton and shuts off the PMIC.
Hence the split in omap_rtc_power_off.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
[tony@atomide.com: folded in a fix for compile warning]
Signed-off-by: Tony Lindgren <tony@atomide.com>
After commit a297569fe0 ("net/udp: do not touch skb->peeked unless
really needed") the 'peeked' argument of __skb_try_recv_datagram()
and friends is always equal to !!'flags & MSG_PEEK'.
Since such argument is really a boolean info, and the callers have
already 'flags & MSG_PEEK' handy, we can remove it and clean-up the
code a bit.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most dma_map_ops implementations already had some issues with a NULL
device, or did simply crash if one was fed to them. Now that we have
cleaned up all the obvious offenders we can stop to pretend we
support this mode.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit 6dc4f100c1 ("block: allow bio_for_each_segment_all() to
iterate over multi-page bvec") changes bio_for_each_segment_all()
to use for-inside-for.
This way breaks all bio_for_each_segment_all() call with error out
branch via 'break', since now 'break' can only break from the inner
loop.
Fixes this issue by implementing bio_for_each_segment_all() via
single 'for' loop, and now the logic is very similar with normal
bvec iterator.
Cc: Qu Wenruo <quwenruo.btrfs@gmx.com>
Cc: linux-btrfs@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
Cc: Omar Sandoval <osandov@fb.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-and-Tested-by: Qu Wenruo <quwenruo.btrfs@gmx.com>
Fixes: 6dc4f100c1 ("block: allow bio_for_each_segment_all() to iterate over multi-page bvec")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Removing explicit calls to mmiowb() from driver code means that we must
now call into the generic mmiowb_spin_{lock,unlock}() functions from the
core spinlock code. In order to elide barriers following critical
sections without any I/O writes, we also hook into the asm-generic I/O
routines.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
While the cpuinfo.max_freq value doesn't really matter for
intel_pstate in the active mode, in the passive mode it is used by
governors as the maximum physical frequency of the CPU and the
results of governor computations generally depend on it. Also it
is made available to user space via sysfs and it should match the
current HW configuration.
For this reason, make intel_pstate update cpuinfo.max_freq for all
CPUs if it detects a global change of turbo frequency settings from
"disable" to "enable" or the other way associated with a _PPC change
notification from the platform firmware.
Note that policy_is_inactive(), cpufreq_cpu_acquire(),
cpufreq_cpu_release(), and cpufreq_set_policy() need to be made
available to it for this purpose.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200759
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The direction inversion semantics are now handled by simply
using the registers for in/out available, no need to keep
track of inversion semantics exmplicitly anymore.
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The symbol that is being used in the #if/#endif block is not the one
which is mentioned at the bottom.
Fixes: 93af53b863 ("nand: omap2: Remove horrible ifdefs to fix module probe")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_device embeds a nand_ecc_req object which contains the minimum
strength and step-size required by the NAND device.
Drop the chip->ecc_{strength,step}_ds fields and use
chip->base.eccreq.{strength,step_size} instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
The target size can now be returned by nanddev_get_targetsize(). Get
rid of the chip->chipsize field and use this helper instead.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that we inherit from nand_device, we can use
nand_device->memorg.bits_per_cell instead of having our own field at
the nand_chip level.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
nanddev_mtd_max_bad_blocks() is implemented by the generic NAND layer
and is already doing what we need. Reuse this function instead of
having our own implementation.
While at it, get rid of the ->max_bb_per_die and ->blocks_per_die
fields which are now unused.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Looking at the field names it's hard to tell what ->data_buf, ->pagebuf
and ->pagebuf_bitflips are for. Clarify that by moving those fields
in a sub-struct named pagecache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
We plan to move cache related fields to a pagecache struct in nand_chip
but some drivers access ->pagebuf directly to invalidate the cache
before they start using ->data_buf.
Let's provide an helper that returns a pointer to ->data_buf after
invalidating the cache.
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
