Currently ICM has been handling XDomain UUID exchange so there was no
need to have it in the driver yet. However, since now we are going to
add the same capabilities to the software connection manager it needs to
be handled properly.
For this reason modify the driver XDomain protocol handling so that if
the remote domain UUID is not filled in the core will query it first and
only then start the normal property exchange flow.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
To be able to check and set bad block markers in the first and
second page of a block independently of each other, we create
separate flags for both cases.
Previously NAND_BBM_SECONDPAGE meant, that both, the first and the
second page were used. With this patch NAND_BBM_FIRSTPAGE stands for
using the first page and NAND_BBM_SECONDPAGE for using the second
page.
This patch is only for preparation of subsequent changes and does
not implement the logic to actually handle both flags separately.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The information about where the manufacturer puts the bad block
markers inside the bad block and in the OOB data is stored in
different places. Let's move this information to the chip struct,
as we did it for rawnand.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The information about where the manufacturer puts the bad block
markers inside the bad block and in the OOB data is stored in
different places. Let's move this information to nand_chip.options
and nand_chip.badblockpos.
As this chip-specific information is not directly related to the
bad block table (BBT), we also rename the flags to NAND_BBM_*.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, drivers are able to constify a nand_op_parser array,
but not nand_op_parser_pattern and nand_op_parser_pattern_elem
since they are instantiated by using the NAND_OP_PARSER(_PATTERN).
Add 'const' to them in order to move more driver data from .data to
.rodata section.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Sphinx doesn't handle expressions in identifier references.
This fixes the following warnings:
./include/linux/mtd/rawnand.h:1184: WARNING: Inline strong start-string without end-string.
./include/linux/mtd/rawnand.h:1186: WARNING: Inline strong start-string without end-string.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no point in having two distinct entries, merge them and
rename the symbol for more clarity: MTD_NAND_ECC_SW_BCH
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The function build_skb() also have the responsibility to allocate and clear
the SKB structure. Introduce a new function build_skb_around(), that moves
the responsibility of allocation and clearing to the caller. This allows
caller to use kmem_cache (slab/slub) bulk allocation API.
Next patch use this function combined with kmem_cache_alloc_bulk.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The Switchtec devices supports two PCIe Function Frameworks (PFFs) per
upstream port (one for the port itself and one for the management endoint),
and each PFF may have up to 255 ports. Previously the driver only
supported 48 of those ports, and the SWITCHTEC_IOCTL_EVENT_SUMMARY ioctl
only returned information about those 48.
Increase SWITCHTEC_MAX_PFF_CSR from 48 to 255 so the driver supports all
255 possible ports.
Rename SWITCHTEC_IOCTL_EVENT_SUMMARY and associated struct
switchtec_ioctl_event_summary to SWITCHTEC_IOCTL_EVENT_SUMMARY_LEGACY and
switchtec_ioctl_event_summary_legacy with so existing applications work
unchanged, supporting up to 48 ports.
Add replacement SWITCHTEC_IOCTL_EVENT_SUMMARY and struct
switchtec_ioctl_event_summary that new and recompiled applications support
up to 255 ports.
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
pci_request_region_exclusive() was introduced with commit e8de1481fd
("resource: allow MMIO exclusivity for device drivers") in 2.6.29 which
was released 2008.
It never had an in tree user since then, so after 11 years later let's
remove it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that all files were converted to ReST format, rename them
and add an index.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull networking fixes from David Miller:
1) Handle init flow failures properly in iwlwifi driver, from Shahar S
Matityahu.
2) mac80211 TXQs need to be unscheduled on powersave start, from Felix
Fietkau.
3) SKB memory accounting fix in A-MDSU aggregation, from Felix Fietkau.
4) Increase RCU lock hold time in mlx5 FPGA code, from Saeed Mahameed.
5) Avoid checksum complete with XDP in mlx5, also from Saeed.
6) Fix netdev feature clobbering in ibmvnic driver, from Thomas Falcon.
7) Partial sent TLS record leak fix from Jakub Kicinski.
8) Reject zero size iova range in vhost, from Jason Wang.
9) Allow pending work to complete before clcsock release from Karsten
Graul.
10) Fix XDP handling max MTU in thunderx, from Matteo Croce.
11) A lot of protocols look at the sa_family field of a sockaddr before
validating it's length is large enough, from Tetsuo Handa.
12) Don't write to free'd pointer in qede ptp error path, from Colin Ian
King.
13) Have to recompile IP options in ipv4_link_failure because it can be
invoked from ARP, from Stephen Suryaputra.
14) Doorbell handling fixes in qed from Denis Bolotin.
15) Revert net-sysfs kobject register leak fix, it causes new problems.
From Wang Hai.
16) Spectre v1 fix in ATM code, from Gustavo A. R. Silva.
17) Fix put of BROPT_VLAN_STATS_PER_PORT in bridging code, from Nikolay
Aleksandrov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (111 commits)
socket: fix compat SO_RCVTIMEO_NEW/SO_SNDTIMEO_NEW
tcp: tcp_grow_window() needs to respect tcp_space()
ocelot: Clean up stats update deferred work
ocelot: Don't sleep in atomic context (irqs_disabled())
net: bridge: fix netlink export of vlan_stats_per_port option
qed: fix spelling mistake "faspath" -> "fastpath"
tipc: set sysctl_tipc_rmem and named_timeout right range
tipc: fix link established but not in session
net: Fix missing meta data in skb with vlan packet
net: atm: Fix potential Spectre v1 vulnerabilities
net/core: work around section mismatch warning for ptp_classifier
net: bridge: fix per-port af_packet sockets
bnx2x: fix spelling mistake "dicline" -> "decline"
route: Avoid crash from dereferencing NULL rt->from
MAINTAINERS: normalize Woojung Huh's email address
bonding: fix event handling for stacked bonds
Revert "net-sysfs: Fix memory leak in netdev_register_kobject"
rtnetlink: fix rtnl_valid_stats_req() nlmsg_len check
qed: Fix the DORQ's attentions handling
qed: Fix missing DORQ attentions
...
Path lookups that traverse encrypted symlink(s) are very slow because
each encrypted symlink needs to be decrypted each time it's followed.
This also involves dropping out of rcu-walk mode.
Make encrypted symlinks faster by caching the decrypted symlink target
in ->i_link. The first call to fscrypt_get_symlink() sets it. Then,
the existing VFS path lookup code uses the non-NULL ->i_link to take the
fast path where ->get_link() isn't called, and lookups in rcu-walk mode
remain in rcu-walk mode.
Also set ->i_link immediately when a new encrypted symlink is created.
To safely free the symlink target after an RCU grace period has elapsed,
introduce a new function fscrypt_free_inode(), and make the relevant
filesystems call it just before actually freeing the inode.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Move the Trusted Foundations support out of arch/arm/firmware and into
drivers/firmware where most other firmware support implementations are
located.
Signed-off-by: Thierry Reding <treding@nvidia.com>
->lookup() in an encrypted directory begins as follows:
1. fscrypt_prepare_lookup():
a. Try to load the directory's encryption key.
b. If the key is unavailable, mark the dentry as a ciphertext name
via d_flags.
2. fscrypt_setup_filename():
a. Try to load the directory's encryption key.
b. If the key is available, encrypt the name (treated as a plaintext
name) to get the on-disk name. Otherwise decode the name
(treated as a ciphertext name) to get the on-disk name.
But if the key is concurrently added, it may be found at (2a) but not at
(1a). In this case, the dentry will be wrongly marked as a ciphertext
name even though it was actually treated as plaintext.
This will cause the dentry to be wrongly invalidated on the next lookup,
potentially causing problems. For example, if the racy ->lookup() was
part of sys_mount(), then the new mount will be detached when anything
tries to access it. This is despite the mountpoint having a plaintext
path, which should remain valid now that the key was added.
Of course, this is only possible if there's a userspace race. Still,
the additional kernel-side race is confusing and unexpected.
Close the kernel-side race by changing fscrypt_prepare_lookup() to also
set the on-disk filename (step 2b), consistent with the d_flags update.
Fixes: 28b4c26396 ("ext4 crypto: revalidate dentry after adding or removing the key")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Make __d_move() clear DCACHE_ENCRYPTED_NAME on the source dentry. This
is needed for when d_splice_alias() moves a directory's encrypted alias
to its decrypted alias as a result of the encryption key being added.
Otherwise, the decrypted alias will incorrectly be invalidated on the
next lookup, causing problems such as unmounting a mount the user just
mount()ed there.
Note that we don't have to support arbitrary moves of this flag because
fscrypt doesn't allow dentries with DCACHE_ENCRYPTED_NAME to be the
source or target of a rename().
Fixes: 28b4c26396 ("ext4 crypto: revalidate dentry after adding or removing the key")
Reported-by: Sarthak Kukreti <sarthakkukreti@chromium.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Close some race conditions where fscrypt allowed rename() and link() on
ciphertext dentries that had been looked up just prior to the key being
concurrently added. It's better to return -ENOKEY in this case.
This avoids doing the nonsensical thing of encrypting the names a second
time when searching for the actual on-disk dir entries. It also
guarantees that DCACHE_ENCRYPTED_NAME dentries are never rename()d, so
the dcache won't have support all possible combinations of moving
DCACHE_ENCRYPTED_NAME around during __d_move().
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Make various improvements to fscrypt dentry revalidation:
- Don't try to handle the case where the per-directory key is removed,
as this can't happen without the inode (and dentries) being evicted.
- Flag ciphertext dentries rather than plaintext dentries, since it's
ciphertext dentries that need the special handling.
- Avoid doing unnecessary work for non-ciphertext dentries.
- When revalidating ciphertext dentries, try to set up the directory's
i_crypt_info to make sure the key is really still absent, rather than
invalidating all negative dentries as the previous code did. An old
comment suggested we can't do this for locking reasons, but AFAICT
this comment was outdated and it actually works fine.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Add a new phy_ops *release* invoked when the consumer relinquishes the
PHY using phy_put/devm_phy_put. The initializations done by the PHY
driver in of_xlate call back can be can be cleaned up here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
->i_crypt_info starts out NULL and may later be locklessly set to a
non-NULL value by the cmpxchg() in fscrypt_get_encryption_info().
But ->i_crypt_info is used directly, which technically is incorrect.
It's a data race, and it doesn't include the data dependency barrier
needed to safely dereference the pointer on at least one architecture.
Fix this by using READ_ONCE() instead. Note: we don't need to use
smp_load_acquire(), since dereferencing the pointer only requires a data
dependency barrier, which is already included in READ_ONCE(). We also
don't need READ_ONCE() in places where ->i_crypt_info is unconditionally
dereferenced, since it must have already been checked.
Also downgrade the cmpxchg() to cmpxchg_release(), since RELEASE
semantics are sufficient on the write side.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
The only reason the inode is being passed to fscrypt_get_ctx() is to
verify that the encryption key is available. However, all callers
already ensure this because if we get as far as trying to do I/O to an
encrypted file without the key, there's already a bug.
Therefore, remove this unnecessary argument.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Handling of extended interrupts (kickstart, wake-up, ram-clear) was
moved off to a work queue, but the interrupts aren't acknowledged
in the interrupt handler. This leads to a deadlock, if driver
is used with interrupts. To fix this we use a threaded interrupt, get rid
of the work queue and do locking with just the rtc mutex lock.
Fixes: aaaf5fbf56 ("rtc: add driver for DS1685 family of real time clocks")
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Pull KVM fixes from Paolo Bonzini:
"5.1 keeps its reputation as a big bugfix release for KVM x86.
- Fix for a memory leak introduced during the merge window
- Fixes for nested VMX with ept=0
- Fixes for AMD (APIC virtualization, NMI injection)
- Fixes for Hyper-V under KVM and KVM under Hyper-V
- Fixes for 32-bit SMM and tests for SMM virtualization
- More array_index_nospec peppering"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (21 commits)
KVM: x86: avoid misreporting level-triggered irqs as edge-triggered in tracing
KVM: fix spectrev1 gadgets
KVM: x86: fix warning Using plain integer as NULL pointer
selftests: kvm: add a selftest for SMM
selftests: kvm: fix for compilers that do not support -no-pie
selftests: kvm/evmcs_test: complete I/O before migrating guest state
KVM: x86: Always use 32-bit SMRAM save state for 32-bit kernels
KVM: x86: Don't clear EFER during SMM transitions for 32-bit vCPU
KVM: x86: clear SMM flags before loading state while leaving SMM
KVM: x86: Open code kvm_set_hflags
KVM: x86: Load SMRAM in a single shot when leaving SMM
KVM: nVMX: Expose RDPMC-exiting only when guest supports PMU
KVM: x86: Raise #GP when guest vCPU do not support PMU
x86/kvm: move kvm_load/put_guest_xcr0 into atomic context
KVM: x86: svm: make sure NMI is injected after nmi_singlestep
svm/avic: Fix invalidate logical APIC id entry
Revert "svm: Fix AVIC incomplete IPI emulation"
kvm: mmu: Fix overflow on kvm mmu page limit calculation
KVM: nVMX: always use early vmcs check when EPT is disabled
KVM: nVMX: allow tests to use bad virtual-APIC page address
...
Use the new xfer_atomic callback to check a newly introduced flag to
whitelist atomic transfers. This will report configurations which
worked accidently.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We had the request to access devices very late when interrupts are not
available anymore multiple times now. Mostly to prepare shutdown or
reboot. Allow adapters to specify a specific callback for this case.
Note that we fall back to the generic {master|smbus}_xfer callback if
this new atomic one is not present. This is intentional to preserve the
previous behaviour and avoid regressions. Because there are drivers not
using interrupts or because it might have worked "accidently" before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Stefan Lengfeld <contact@stefanchrist.eu>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It takes a fair amount of boiler plate code to add new sensors, add a
macro that can be used to specify simple static sensors.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Emit an audit record every time selected NTP parameters are modified
from userspace (via adjtimex(2) or clock_adjtime(2)). These parameters
may be used to indirectly change system clock, and thus their
modifications should be audited.
Such events will now generate records of type AUDIT_TIME_ADJNTPVAL
containing the following fields:
- op -- which value was adjusted:
- offset -- corresponding to the time_offset variable
- freq -- corresponding to the time_freq variable
- status -- corresponding to the time_status variable
- adjust -- corresponding to the time_adjust variable
- tick -- corresponding to the tick_usec variable
- tai -- corresponding to the timekeeping's TAI offset
- old -- the old value
- new -- the new value
Example records:
type=TIME_ADJNTPVAL msg=audit(1530616044.507:7): op=status old=64 new=8256
type=TIME_ADJNTPVAL msg=audit(1530616044.511:11): op=freq old=0 new=49180377088000
The records of this type will be associated with the corresponding
syscall records.
An overview of parameter changes that can be done via do_adjtimex()
(based on information from Miroslav Lichvar) and whether they are
audited:
__timekeeping_set_tai_offset() -- sets the offset from the
International Atomic Time
(AUDITED)
NTP variables:
time_offset -- can adjust the clock by up to 0.5 seconds per call
and also speed it up or slow down by up to about
0.05% (43 seconds per day) (AUDITED)
time_freq -- can speed up or slow down by up to about 0.05%
(AUDITED)
time_status -- can insert/delete leap seconds and it also enables/
disables synchronization of the hardware real-time
clock (AUDITED)
time_maxerror, time_esterror -- change error estimates used to
inform userspace applications
(NOT AUDITED)
time_constant -- controls the speed of the clock adjustments that
are made when time_offset is set (NOT AUDITED)
time_adjust -- can temporarily speed up or slow down the clock by up
to 0.05% (AUDITED)
tick_usec -- a more extreme version of time_freq; can speed up or
slow down the clock by up to 10% (AUDITED)
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Emit an audit record whenever the system clock is changed (i.e. shifted
by a non-zero offset) by a syscall from userspace. The syscalls than can
(at the time of writing) trigger such record are:
- settimeofday(2), stime(2), clock_settime(2) -- via
do_settimeofday64()
- adjtimex(2), clock_adjtime(2) -- via do_adjtimex()
The new records have type AUDIT_TIME_INJOFFSET and contain the following
fields:
- sec -- the 'seconds' part of the offset
- nsec -- the 'nanoseconds' part of the offset
Example record (time was shifted backwards by ~15.875 seconds):
type=TIME_INJOFFSET msg=audit(1530616049.652:13): sec=-16 nsec=124887145
The records of this type will be associated with the corresponding
syscall records.
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Reviewed-by: Richard Guy Briggs <rgb@redhat.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
[PM: fixed a line width problem in __audit_tk_injoffset()]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Remove the broute pseudo hook, implement this from the bridge
prerouting hook instead. Now broute becomes real table in ebtables,
from Florian Westphal. This also includes a size reduction patch for the
bridge control buffer area via squashing boolean into bitfields and
a selftest.
2) Add OS passive fingerprint version matching, from Fernando Fernandez.
3) Support for gue encapsulation for IPVS, from Jacky Hu.
4) Add support for NAT to the inet family, from Florian Westphal.
This includes support for masquerade, redirect and nat extensions.
5) Skip interface lookup in flowtable, use device in the dst object.
6) Add jiffies64_to_msecs() and use it, from Li RongQing.
7) Remove unused parameter in nf_tables_set_desc_parse(), from Colin Ian King.
8) Statify several functions, patches from YueHaibing and Florian Westphal.
9) Add an optimized version of nf_inet_addr_cmp(), from Li RongQing.
10) Merge route extension to core, also from Florian.
11) Use IS_ENABLED(CONFIG_NF_NAT) instead of NF_NAT_NEEDED, from Florian.
12) Merge ip/ip6 masquerade extensions, from Florian. This includes
netdevice notifier unification.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current API for the wilco EC mailbox interface is bad.
It assumes that most messages sent to the EC follow a similar structure,
with a command byte in MBOX[0], followed by a junk byte, followed by
actual data. This doesn't happen in several cases, such as setting the
RTC time, using the raw debugfs interface, and reading or writing
properties such as the Peak Shift policy (this last to be submitted soon).
Similarly for the response message from the EC, the current interface
assumes that the first byte of data is always 0, and the second byte
is unused. However, in both setting and getting the RTC time, in the
debugfs interface, and for reading and writing properties, this isn't
true.
The current way to resolve this is to use WILCO_EC_FLAG_RAW* flags to
specify when and when not to skip these initial bytes in the sent and
received message. They are confusing and used so much that they are
normal, and not exceptions. In addition, the first byte of
response in the debugfs interface is still always skipped, which is
weird, since this raw interface should be giving the entire result.
Additionally, sent messages assume the first byte is a command, and so
struct wilco_ec_message contains the "command" field. In setting or
getting properties however, the first byte is not a command, and so this
field has to be filled with a byte that isn't actually a command. This
is again inconsistent.
wilco_ec_message contains a result field as well, copied from
wilco_ec_response->result. The message result field should be removed:
if the message fails, the cause is already logged, and the callers are
alerted. They will never care about the actual state of the result flag.
These flags and different cases make the wilco_ec_transfer() function,
used in wilco_ec_mailbox(), really gross, dealing with a bunch of
different cases. It's difficult to figure out what it is doing.
Finally, making these assumptions about the structure of a message make
it so that the messages do not correspond well with the specification
for the EC's mailbox interface. For instance, this interface
specification may say that MBOX[9] in the received message contains
some information, but the calling code needs to remember that the first
byte of response is always skipped, and because it didn't set the
RESPONSE_RAW flag, the next byte is also skipped, so this information
is actually contained within wilco_ec_message->response_data[7]. This
makes it difficult to maintain this code in the future.
To fix these problems this patch standardizes the mailbox interface by:
- Removing the WILCO_EC_FLAG_RAW* flags
- Removing the command and reserved_raw bytes from wilco_ec_request
- Removing the mbox0 byte from wilco_ec_response
- Simplifying wilco_ec_transfer() because of these changes
- Gives the callers of wilco_ec_mailbox() the responsibility of exactly
and consistently defining the structure of the mailbox request and
response
- Removing command and result from wilco_ec_message.
This results in the reduction of total code, and makes it much more
maintainable and understandable.
Signed-off-by: Nick Crews <ncrews@chromium.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
The address that is allocated using pci_epf_alloc_space() is
directly written to the target address of the Inbound Address
Translation unit (ie the HW component implementing inbound address
decoding) on endpoint controllers.
Designware IP [1] has a configuration parameter (CX_ATU_MIN_REGION_SIZE
[2]) which has 64KB as default value and the lower 16 bits of the Base,
Limit and Target registers of the Inbound ATU are fixed to zero. If the
programmed memory address is not aligned to 64 KB boundary this causes
memory corruption.
Modify pci_epf_alloc_space() API to take alignment size as argument in
order to allocate buffers to be mapped to BARs with an alignment that
suits the platform where they are used.
Add an 'align' parameter to epc_features which can be used by platform
drivers to specify the BAR allocation alignment requirements and use
this while invoking pci_epf_alloc_space().
[1] "I/O and MEM Match Modes" section in DesignWare Cores PCI Express
Controller Databook version 4.90a
[2] http://www.ti.com/lit/ug/spruid7c/spruid7c.pdf
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
In commit b1fca27d38 ("kernel debug: support resetting WARN*_ONCE")
we got the opportunity to reset state on the one shot messages,
without having to reboot.
However printk_once (printk_deferred_once) live in a different file
and didn't get the same kind of update/conversion, so they remain
unconditionally one shot, until the system is rebooted.
For example, we currently have:
sched/rt.c: printk_deferred_once("sched: RT throttling activated\n");
..which could reasonably be tripped as someone is testing and tuning
a new system/workload and their task placements. For consistency, and
to avoid reboots in the same vein as the original commit, we make these
two instances of _once the same as the WARN*_ONCE instances are.
Link: http://lkml.kernel.org/r/1555121491-31213-1-git-send-email-paul.gortmaker@windriver.com
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
This Patch Adds fpga API's to support the Bitstream loading
by using firmware interface.
Signed-off-by: Nava kishore Manne <nava.manne@xilinx.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Merge page ref overflow branch.
Jann Horn reported that he can overflow the page ref count with
sufficient memory (and a filesystem that is intentionally extremely
slow).
Admittedly it's not exactly easy. To have more than four billion
references to a page requires a minimum of 32GB of kernel memory just
for the pointers to the pages, much less any metadata to keep track of
those pointers. Jann needed a total of 140GB of memory and a specially
crafted filesystem that leaves all reads pending (in order to not ever
free the page references and just keep adding more).
Still, we have a fairly straightforward way to limit the two obvious
user-controllable sources of page references: direct-IO like page
references gotten through get_user_pages(), and the splice pipe page
duplication. So let's just do that.
* branch page-refs:
fs: prevent page refcount overflow in pipe_buf_get
mm: prevent get_user_pages() from overflowing page refcount
mm: add 'try_get_page()' helper function
mm: make page ref count overflow check tighter and more explicit
Change pipe_buf_get() to return a bool indicating whether it succeeded
in raising the refcount of the page (if the thing in the pipe is a page).
This removes another mechanism for overflowing the page refcount. All
callers converted to handle a failure.
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the same as the traditional 'get_page()' function, but instead
of unconditionally incrementing the reference count of the page, it only
does so if the count was "safe". It returns whether the reference count
was incremented (and is marked __must_check, since the caller obviously
has to be aware of it).
Also like 'get_page()', you can't use this function unless you already
had a reference to the page. The intent is that you can use this
exactly like get_page(), but in situations where you want to limit the
maximum reference count.
The code currently does an unconditional WARN_ON_ONCE() if we ever hit
the reference count issues (either zero or negative), as a notification
that the conditional non-increment actually happened.
NOTE! The count access for the "safety" check is inherently racy, but
that doesn't matter since the buffer we use is basically half the range
of the reference count (ie we look at the sign of the count).
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have a VM_BUG_ON() to check that the page reference count doesn't
underflow (or get close to overflow) by checking the sign of the count.
That's all fine, but we actually want to allow people to use a "get page
ref unless it's already very high" helper function, and we want that one
to use the sign of the page ref (without triggering this VM_BUG_ON).
Change the VM_BUG_ON to only check for small underflows (or _very_ close
to overflowing), and ignore overflows which have strayed into negative
territory.
Acked-by: Matthew Wilcox <willy@infradead.org>
Cc: Jann Horn <jannh@google.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extend the inkern API with a function for reading available
attribute values of iio channels.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A previous commit moved the shallow depth and BFQ depth map calculations
to be done at init time, moving it outside of the hotter IO path. This
potentially causes hangs if the users changes the depth of the scheduler
map, by writing to the 'nr_requests' sysfs file for that device.
Add a blk-mq-sched hook that allows blk-mq to inform the scheduler if
the depth changes, so that the scheduler can update its internal state.
Tested-by: Kai Krakow <kai@kaishome.de>
Reported-by: Paolo Valente <paolo.valente@linaro.org>
Fixes: f0635b8a41 ("bfq: calculate shallow depths at init time")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
