Add mux-controller DT node as a child node of scm_conf. This is
required for muxing SERDES between USB, PCIe and ICSS2 SGMII.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
GIC_ITS used in AM654 platform has the same configuration as that of
GIC_ITS used in Socionext SoCs. Add "socionext,synquacer-pre-its"
property to get PCI MSI working.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the MSCM RAM address space to the ranges property of the cbass_main
interconnect node so that the addresses can be translated properly.
This fixes the probe failure in the sram driver for the MSMC RAM node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the address spaces for the R5F cores in MCU domain to the ranges
property of the cbass_mcu interconnect node so that the addresses
within the R5F nodes can be translated properly by the relevant OF
address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the on-chip SRAM present within the MCU domain as a mmio-sram node.
The K3 AM65x SoCs have 512 KB of such memory. Any specific memory range
within this RAM needed by a software module ought to be reserved using
an appropriate child node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add the address space for the MCU SRAM memory to the ranges property
of the cbass_mcu interconnect node so that the addresses within the
mcu_sram nodes and its children can be translated properly by the
relevant OF address API.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There are 2 push buttons: SW5 and SW6 that are basically connected to
WKUP_GPIO0_24 and WKUP_GPIO0_27 respectively. Add the respective
nodes and the pinctrl data to set the mode to GPIO and Input.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add gpio0/1 nodes under main domain. They have 96 and 90 gpios
respectively and all are capable of generating banked interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add gpio0 node under wakeup domain. This has 56 gpios
and all are capable of generating banked interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Wakeup domain in AM654 SoC has an interrupt router connected to gpio
in wakeup domain. Add DT node for this interrupt router.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Main domain in AM654 has the following interrupt controller instances:
- Main Domain GPIO Interrupt router connected to gpio in main domain.
- Under the Main Domain Navigator Subsystem(NAVSS)
- Main Navss Interrupt Router connected to main navss inta and mailboxes.
- Main Navss Interrupt Aggregator connected to main domain UDMASS
Add DT nodes for the above three interrupt controllers available
in main domain.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Use the am654 specific compatible for dmsc. This allows to use
the am654 specific RM mapping table.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Similarly to what done for the r8a7796 with commit 737e05bf03
("arm64: dts: renesas: revise properties for R-Car Gen3 SoCs'
usb 2.0"), this patch lists the clock for the USB High-Speed Module
(HS-USB) with the USB2.0 Host (EHCI/OHCI) IP DT node, and it lists
the clock for the USB2.0 Host IP with the HS-USB module DT node.
Fixes: 4c2c2fb998 ("arm64: dts: renesas: r8a774a1: Add USB2.0 phy and host(EHCI/OHCI) device nodes")
Fixes: ed898d4fc1 ("arm64: dts: renesas: r8a774a1: Add USB-DMAC and HSUSB device nodes")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch is to add ptp timer device tree node for dpaa2
platforms(ls1088a/ls208xa/lx2160a).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable the sound card on the X96 Max, enabling HDMI output using the
TDM interface B, being aligned on other boards sound cards.
SPDI/F support is also enabled to the physical toslink port and to HDMI.
The internal DAC connected to the audio jack will be added later on, when
driver support is added.
Tested by running:
tinymix set "FRDDR_A SRC 1 EN Switch" 1
tinymix set "FRDDR_A SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_B SRC 1 EN Switch" 1
tinymix set "FRDDR_B SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_C SRC 1 EN Switch" 1
tinymix set "FRDDR_C SINK 1 SEL" "OUT 1"
tinymix set "TOHDMITX I2S SRC" "I2S B"
tinymix set "TOHDMITX Switch" 1
then:
tinymix set "TDMOUT_B SRC SEL" "IN 0"
speaker-test -Dhw:0,0 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 1"
speaker-test -Dhw:0,1 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 2"
speaker-test -Dhw:0,2 -c2
testing HDMI audio output from the all 3 ASoC playback interfaces.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the sound card on the Hardkernel Odroid-N2, enabling HDMI output
using the TDM interface B, being aligned on other boards sound cards.
The internal DAC connected to the audio jack will be added later on, when
driver support is added.
Tested by running:
tinymix set "FRDDR_A SRC 1 EN Switch" 1
tinymix set "FRDDR_A SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_B SRC 1 EN Switch" 1
tinymix set "FRDDR_B SINK 1 SEL" "OUT 1"
tinymix set "FRDDR_C SRC 1 EN Switch" 1
tinymix set "FRDDR_C SINK 1 SEL" "OUT 1"
tinymix set "TOHDMITX I2S SRC" "I2S B"
tinymix set "TOHDMITX Switch" 1
then:
tinymix set "TDMOUT_B SRC SEL" "IN 0"
speaker-test -Dhw:0,0 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 1"
speaker-test -Dhw:0,1 -c2
then:
tinymix set "TDMOUT_B SRC SEL" "IN 2"
speaker-test -Dhw:0,2 -c2
testing HDMI audio output from the all 3 ASoC playback interfaces.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the sound card on the sei510:
* TDM interface A is connected to an external DAC and a speaker installed
on the device.
* HDMI is expected to use TDM B. It can also use TDM A but will be
limited to 2 channels, as accepted by the external DAC.
* 2 Built in PDM mics through the PDM interface.
* Both TDM outputs may use HW loopback.
The internal DAC connected to audio jack will be added later on, when
driver support is added.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Due to an integration issue the architected timer on Tegra210 does not
remain on during system suspend (a.k.a. SC7). Mark it accordingly so
that it isn't considered as a means to track suspend time.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The architected timer on Tegra186 and Tegra194 is in an always on power
partition and its reference clock will always run, so mark the timer as
always on.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add devicetree support for Khadas Edge/Edge-V/Captain boards.
Khadas Edge is an expandable Rockchip RK3399 board with goldfinger.
Khadas Captain is the carrier board for Khadas Edge.
Khadas Edge-V is a Khadas VIM form factor Rockchip RK3399 board.
Signed-off-by: Nick Xie <nick@khadas.com>
[edge-captain and edge-v contain different components that are supposed
to get added in future patches, so should stay separate while looking
somewhat similar right now]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This commit enables the hdmi-sound device needed to have
audio over HDMI on the Rock Pi board.
Fixes: 1b5715c602 ("arm64: dts: rockchip: add ROCK Pi 4 DTS support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch enables TI HD3SS3220 device and support usb role switch
for the CAT 874 platform.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MDSS and its friends complain about the DTS is using legacy clock names,
update these to silence the warnings.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The current entry-latency-us is too short.
The proper way to convert between the device tree properties
from the vendor tree to the upstream PSCI device tree properties is:
entry-latency-us = qcom,time-overhead - qcom,latency-us
which gives
entry-latency-us = 210 - 80 = 130
Fixes: f6aee7af59 ("arm64: dts: qcom: msm8996: Add PSCI cpuidle low power states")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
PSCI spec define 1st parameter's bit 16 of function CPU_SUSPEND to
indicate CPU State Type: 0 for standby, 1 for power down. In this
case, we want to select standby for CPU idle feature. But current
setting wrongly select power down and cause CPU SUSPEND fail every
time. Need this fix.
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPIO interrupts are used for the external Ethernet RGMII PHY interrupt
line.
Add the GPIO interrupt controller so we can describe that connection in
the dts files.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The 32k low power clock is necessary for the bluetooth part of the
combo module to initialize correctly, simply add the same clock we
use for the sdio pwrseq.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The 32k low power clock is necessary for the bluetooth part of the
combo module to initialize correctly, simply add the same clock we
use for the sdio pwrseq.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
