Some drivers can detect subsystem failures e.g. shared memory driver
can detect modem sub system failures. It would be helpful in analyzing
these failures if AB register dump is available at that point. This
patch adds the API for the drivers to dump AB registers in the kernel
log.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Reviewed-by: Linus WALLEIJ <linus.walleij@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
To make the partitions writable they should aligned to erase sizes of
the flash. If the erase size is small use 0x10000.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
When platform_driver_probe() is used and no device is registered for
this driver -ENODEV is returned and and error message is shown. Not all
BCM47xx SoC have a nand flash chip controller and chip and for them an
error message was shown.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The resolution of msleep is related to HZ, so with HZ set to
100 any msleep of less than 10ms will become ~10ms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When platform_driver_probe() is used and no device is registered for
this driver -ENODEV is returned and and error message is shown. Not all
BCM47xx SoC have a serial flash chip controller and chip and for them
an error message was shown.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
It's possible to supply a string to provide a reason for
triggering a restart. In this case our reason is to enter
charging-only mode, as a charger was found to be present.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
When a charger is connected, we usually want AB8500 based systems to
reboot into charging-only mode. However, if the battery type cannot
be identified this would be futile, so we'll just shut the system
down instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Reviewed-by: Karl KOMIEROWSKI <karl.komierowski@stericsson.com>
The kernel allows us to specify a function call-back which will be
invoked when a system power-off request has been received. Here we
provide one which is to be used when shutting down AB8500 based
platforms.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We do the check based on the following two facts:
[1] The mx23/mx28 can only support 20-bits ECC, while the mx6
can supports 40-bits ECC.
[2] The mx23/mx28 can only support the GF13, while the mx6
can supports GF13 and GF14.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The GF13 can be only used in the following case:
The ECC data chunk is less then 1K bytes.
In mx23/mx28, the ecc data chunk is 512 bytes. So it is okay.
But in mx6q, we begin to use some large nand chip whose ecc
data chunk maybe 1K bytes long. So when the data chunk is 1K bytes,
we have to use the GF14.
This patch sets the Golois Field bit when the GF14 is needed.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
As part of removing generalized dependency, replace <xx> literal fields
in DT compatible field with <52> for am335x platforms.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The panic_nand_wait() expects the timeo in ms and not in jiffies.
But in nand_wait(), the timeo for panic_nand_wait() is assigned with
wrong value(jiffies + some delay). The timeo should be set like the
panic_nand_write() does.
This patch passes timeo in ms to panic_nand_wait().
And this patch also passes timeo in jiffies(converted by msecs_to_jiffies)
to time_before() which makes the code more readable.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Currently cfi_cmdset_0002.c does not support PPB locking of sectors. This
patch adds support for this locking/unlocking mechanism. It is needed on
some platforms, since newer U-Boot versions do support this PPB locking
and protect for example their environment sector(s) this way.
This PPB locking/unlocking will be enabled for all devices supported by
cfi_cmdset_0002 reporting 8 in the CFI word 0x49 (Sector Protect/Unprotect
scheme).
Please note that PPB locking does support sector-by-sector locking. But
the whole chip can only be unlocked together. So unlocking one sector
will automatically unlock all sectors of this device. Because of this
chip limitation, the PPB unlocking function saves the current locking
status of all sectors before unlocking the whole device. After unlocking
the saved locking status is re-configured. This way only the addressed
sectors will be unlocked.
To selectively enable this advanced sector protection mechanism, the
device-tree property "use-advanced-sector-protection" has been created.
To enable support for this locking this property needs to be present in the
flash DT node. E.g.:
nor_flash@0,0 {
compatible = "amd,s29gl256n", "cfi-flash";
bank-width = <2>;
use-advanced-sector-protection;
...
Tested with Spansion S29GL512S10THI and Micron JS28F512M29EWx flash
devices.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Add the function name to the error message.
These messages are not very helpful:
[183356.176682] uncorrectable error :
[183356.180273] uncorrectable error :
[183356.184194] uncorrectable error :
[183356.187773] uncorrectable error :
[183356.191280] uncorrectable error :
Artem: amended the patch a bit
Signed-off-by: Tormod Volden <debian.tormod@gmail.com>
in/out_be32 accessors are Power arch centric whereas
ioread/writebe32 are available in other arches.
Since the IFC device registers are annotated big endian in
fsl_ifc.h, the accessor annotations now match, resulting in the
pleasant side-effect of this patch silencing sparse endian
warnings such as the following:
drivers/mtd/nand/fsl_ifc_nand.c:179:19: warning: incorrect type in argument 1 (different base types)
drivers/mtd/nand/fsl_ifc_nand.c:179:19: expected unsigned int volatile [noderef] [usertype] <asn:2>*addr
drivers/mtd/nand/fsl_ifc_nand.c:179:19: got restricted __be32 [noderef] <asn:2>*<noident>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I was (at least) the second person trying to fix a warning by sparse, so
document in the code why this is a bad idea and add an extern declaration to
make sparse happy.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This allows to put the filesystem at a defined address in ROM allowing
to save more precious RAM.
I think it's safe to default to ROM because the intention of using the
uclinux map is to use a romfs and so mtd-ram doesn't give you anything
that mtd-rom doesn't.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
It's required for accessing trx header (usually re-calculating a
checksum) and for writing a new firmware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
ELM module can be used for hardware error correction of BCH 4 & 8 bit.
ELM module functionality is verified by checking the availability of
handle for ELM module in device tree. Hence supporting
1. ELM module available, BCH error correction done by ELM module. Also
support read & write page in one shot by adding custom read_page and
write_page methods. This helps in optimizing code for NAND flashes with
page size less than 4 KB.
2. If ELM module not available fall back to software BCH error
correction support.
New structure member is added to omap_nand_info
1. "is_elm_used" to know the status of whether the ELM module is used for
error correction or not.
2. "elm_dev" device pointer to elm device on detection of ELM module.
Also being here update the device tree documentation of gpmc-nand for
adding optional property elm_id.
Note:
ECC layout uses 1 extra bytes for 512 byte of data to handle erased
pages. Extra byte programmed to zero for programmed pages. Also BCH8
requires 14 byte ecc to maintain compatibility with RBL ECC layout.
This results a common ecc layout across RBL, U-boot & Linux with BCH8.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The ELM hardware module can be used to speedup BCH 4/8/16 ECC scheme
error correction.
For now only 4 & 8 bit support is added
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Remove check of ecc bytes with 13, number of errors can directly update
from nand ecc strength. This will increase re-usability of the code.
Also add macro definitions BCH8_ERROR_MAX & BCH4_ERROR_MAX for better
readability and cleaner code.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Also compress the id in case of a v3 NAND flash controller (i.mx51, i.mx53)
and 16Bit buswidth.
Signed-off-by: Roman Schneider <schneider@at.festo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch adds generic support for flash protection on STmicro chips.
On chips with less than 3 protection bits, the unused bits are don't cares
and so can be written anyway. The lock function will only change the
protection bits if it would not unlock other areas. Similarly, the unlock
function will not lock currently unlocked areas. Tested on the m25p64.
Signed-off-by: Austin Boyle <Austin.Boyle@aviatnet.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The mtd documentation makes no mention of the useful feature whereby
partitions' logical ordering need not match their physical ordering.
Truncation of parts, skipping of zero sized parts, and handling of
overlapping parts are similarly not mentioned.
This updates the comments at the top of file describing the command
line parsing as currently implemented. I proposed this in
http://lists.infradead.org/pipermail/linux-mtd/2012-December/045314.html
Signed-off-by: Christopher Cordahi <christophercordahi@nanometrics.ca>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Decrement index i after skipping a zero sized partition. On next loop
iteration, the index will be the same as before, but the data will be
new as it was moved when earlier partition was skipped.
Signed-off-by: Christopher Cordahi <christophercordahi@nanometrics.ca>
Acked-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Always report corrected and failed ECC stats back up to the MTD layer. Also
return max_bitflips from read_page() as is expected from NAND drivers now.
Signed-off-by: Zach Sadecki <zsadecki@itwatchdogs.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Commit cdeadd712f (mtd: nand: davinci: add OF
support for davinci nand controller) has never been really build tested with
the driver as a module. When the driver is built-in, the missing semicolon
after structure initializer is "compensated" by MODULE_DEVICE_TABLE() macro
being empty and so the initializer using the trailing semicolon on the next
line; when the driver is built as a module, compilation error ensues, and as
the 'davinci_all_defconfig' has the NAND driver modular, this error prevents
DaVinci family kernel from building...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@vger.kernel.org # 3.7
Pull radeon fixes from Dave Airlie:
"I got these late last week, the main chunks of these fix a rendering
regression since 3.7, and the settle ones all fix the issue where we
don't wait long enough for the memory controller to settle after
turning it off which causes bad memory reads, they all fix real users
bugs, and most of them are destined for stable.
Can't remember if you had net connection on that island :-)"
I don't know if the "two tin-cans and a string" thing here on "that
island" can really be considered internet, but I guess I can pull
things. Barely.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: switch back to the CP ring for VM PT updates
drm/radeon: prevent crash in the ring space allocation
drm/radeon: Calling object_unrefer() when creating fb failure
drm/radeon/r5xx-r7xx: wait for the MC to settle after MC blackout
drm/radeon/evergreen+: wait for the MC to settle after MC blackout
drm/radeon: protect against div by 0 in backend setup
drm/radeon: fix backend map setup on 1 RB sumo boards
drm/radeon: add quirk for RV100 board
drm/radeon: add WAIT_UNTIL to the non-VM safe regs list for cayman/TN
drm/radeon: fix MC blackout on evergreen+
FW_STATUS_ABORT can be set only during the user-helper invocation,
thus we can ignore the check when CONFIG_HW_LOADER_USER_HELPER is
disabled.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By shuffling the code, reduce a few ifdefs in firmware_class.c.
Also, firmware_buf fmt field is changed to is_pages_buf boolean for
simplification.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a new kconfig, CONFIG_FW_LOADER_USER_HELPER, and
guards the user-helper codes in firmware_class.c with ifdefs.
Yeah, yeah, there are lots of ifdefs in this patch. The further
clean-up with code shuffling follows in the next.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 3.7 kernel, the firmware loader can read the firmware files
directly, and the traditional user-mode helper is invoked only as a
fallback. This seems working pretty well, and the next step would be
to reduce the redundant user-mode helper stuff in future.
This patch is a preparation for that: refactor the code for splitting
user-mode helper stuff more easily. No functional change.
Acked-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A bus_type has a list of devices (klist_devices), but the list and the
subsys_private structure that contains it are not initialized until the
bus_type is registered with bus_register().
The panic/reboot path has fixups that look up devices in pci_bus_type. If
we panic before registering pci_bus_type, the bus_type exists but the list
does not, so mach_reboot_fixups() trips over a null pointer and panics
again:
mach_reboot_fixups
pci_get_device
..
bus_find_device(&pci_bus_type, ...)
bus->p is NULL
Joonsoo reported a problem when panicking before PCI was initialized.
I think this patch should be sufficient to replace the patch he posted
here: https://lkml.org/lkml/2012/12/28/75 ("[PATCH] x86, reboot: skip
reboot_fixups in early boot phase")
Reported-by: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
