The protocol related code is moved to core stack. So update the host
driver accordingly.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Tested-by: Tim Wang <wangtt@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When switching SD and SDIO cards from 3.3V to 1.8V signal levels, the
clock should be gated for 5 ms during the step. After enabling the
clock, the host should wait for at least 1 ms before checking for
failure. Failure by the card to switch is indicated by dat[0:3] being
pulled low. The host should check for this condition and power-cycle
the card if failure is indicated.
Add a retry mechanism for the SDIO case.
If the voltage switch fails repeatedly, give up and continue the
initialization using the original voltage.
This patch places a couple of requirements on the host driver:
1) mmc_set_ios with ios.clock = 0 must gate the clock
2) mmc_power_off must actually cut the power to the card
3) The card_busy host_ops member must be implemented
if these requirements are not fulfilled, the 1.8V signal voltage switch
will still be attempted but may not be successful.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow callers to access the start_signal_voltage_switch host_ops
member without going through any cmd11 logic. This is mostly a
preparation for the following signal voltage switch patch.
Also, reset ios.signal_voltage to its original value if
start_signal_voltage_switch fails.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
SET_BLOCK_COUNT CMD23 is needed for all access to RPMB partition. If
block count is not set by CMD23, all subsequent read/write commands fail
as per eMMC specification. So, If the host does not support CMD23, do not
expose RPMB partition.
Accessing RPMB partition can cause hang / huge delay for hosts which do
not support CMD23.
Signed-off-by: Balaji T K <balajitk@ti.com>
Reported-and-Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The i.MX esdhc has a nonstandard bit layout for the SDHCI_HOST_CONTROL
register. To support 8bit bus width on i.MX populate the platform_bus_width
callback. This is tested on an i.MX25, but should according to the datasheets
work on the other i.MX using this hardware aswell. The i.MX6, while having
a SDHCI_SPEC_300 controller, still uses the same nonstandard register layout.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The 8bit in the function name is misleading. When set, it will be
used to set the bus width, regardless of whether 8bit or another
bus width is requested, so change the function name to
platform_bus_width.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHCI core will try to use Auto CMD23 for mmc card. Currently, we will
see the following message with mmc card on usdhc due to the lacking of
Auto CMD23 support in the driver.
$ mmc0: new high speed MMC card at address 0001
mmcblk1: mmc0:0001 MMC02G 1.87 GiB
mmcblk1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
mmcblk1: retrying using single block read
mmcblk1:
Enable Auto CMD23 support for usdhc so that mmc card can work in
multiple block mode.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It's another violation to SDHC spec that software reset on usdhc
does not reset MIX_CTRL register. Have to do it manually, otherwise
the preserving of the register bits (e.g. AC23EN) may cause mmc card
fail to be initialized.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The combining of SDHCI_TRANSFER_MODE and SDHCI_COMMAND writes is only
required for esdhc, but not necessarily for usdhc. Different from
esdhc where the bits for transfer mode and command are all in the same
register CMD_XFR_TYP, usdhc has a newly introduced register MIX_CTRL
to hold transfer mode bits. So it makes more sense to separate transfer
mode from command write for usdhc.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Cache control is an eMMC feature and in therefore should be
part of MMC's bus resume operations, performed in mmc_suspend,
rather than in the generic mmc_suspend_host().
Signed-off-by: Maya Erez <merez@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Rename esdhc local definitions with ESDHC_ rather than SDHCI_ prefix,
so that we can distinguish them from SDHCI core definitions from name.
A couple of bit fields are also changed use shift for consistency and
better readability.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHCI_CTRL_D3CD is not a standard SDHCI_HOST_CONTROL, so there is no
need to check it in SDHCI_HOST_CONTROL write at all. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When commit 95a2482 (mmc: sdhci-esdhc-imx: add basic imx6q usdhc
support) works around host version issue on imx6q, it gets the
register address fixup "reg ^= 2" lost for imx25/35/51/53 esdhc.
Thus, the controller version on these SoCs is wrongly identified
as v1 while it's actually v2.
Add the address fixup back and take a different approach to correct
imx6q host version, so that the host version read gets back to work
for all SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
With the __devinit/__devexit attributes having been removed, this
__exitp attribute causes an unused function warning and should be
removed as well.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Chris Ball <cjb@laptop.org>
The original quirk was added in the change 'mmc: dw_mmc: add quirk to
indicate missing write protect line'. The original quirk was added at
a controller level even though each slot has its own write protect (so
the quirk should be at the slot level). A recent change (mmc: dw_mmc:
Add "disable-wp" device tree property) added a slot-level quirk and
support for the quirk directly to dw_mmc.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some SoCs (like exynos5250) you need to use an external GPIO for
write protect. Add support for wp-gpios to the core dw_mmc driver
since it could be useful across multiple SoCs.
With this change I am able to make use of the write protect for the
external SD slot on exynos5250-snow.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
The exynos code claimed the write protect with devm_gpio_request() but
never did anything with it. That meant that anyone using a write
protect GPIO would effectively be write protected all the time.
The handling for wp-gpios belongs in the main dw_mmc driver and has
been moved there.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
The "disable-wp" property is used to specify that a given SD card slot
doesn't have a concept of write protect. This eliminates the need for
special case code for SD slots that should never be write protected
(like a micro SD slot or a dev board).
The dw_mmc driver is special in needing to specify "disable-wp"
because the lack of a "wp-gpios" property means to use the special
purpose write protect line. On some other mmc devices the lack of
"wp-gpios" means that write protect should be disabled.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes the following warning when building with W=1 option:
drivers/mmc/host/mxs-mmc.c: In function 'mxs_mmc_adtc':
drivers/mmc/host/mxs-mmc.c:401:2: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
The warning happens because 'i' is used in 'for_each_sg(sgl, sg, sg_len, i)' and should be made unsigned.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
On many Marvell SoCs, the pins used for the SDIO interface are part of
the MPP pins, that are muxable pins. In order to get the muxing of
those pins correct, this commit integrates the mvsdio driver with the
pinctrl infrastructure by calling devm_pinctrl_get_select_default()
during ->probe().
Note that we permit this function to fail because not all Marvell
platforms have yet been fully converted to using the pinctrl
infrastructure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Stefan Peter <s.peter@mpl.ch>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit ee873fda3b ("gianfar: Pack struct
gfar_priv_grp into three cachelines") moved the irq number and names
off into a separate struct and created accessors for them. However
it was never tested with NET_POLL enabled, and so some conversions
that were simply overlooked went undetected until now.
Make the netpoll ones also use the gfar_irq() accessors.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Jianhua Xie <jianhua.xie@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
On architectures where wmb() is defined as mb(), a build error
happens since there is also a variable named 'mb' in lpfc_sli.c's
lpfc_sli_issue_mbox_s3() function. Rename the variable to 'mbx'
to prevent the build error.
drivers/scsi/lpfc/lpfc_sli.c: error: called object 'mb' is not a function
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In preparation for handling additional sense codes, restructure and cleanup
the error handling code in the command completion code path.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Set scsi_device->no_write_same because the host does not support it.
Also blacklist WRITE_SAME to avoid (and log) accident usage.
If the guest uses the ext4 filesystem, storvsc hangs while it prints
these messages in an endless loop:
...
[ 161.459523] hv_storvsc vmbus_0_1: cmd 0x41 scsi status 0x2 srb status 0x6
[ 161.462157] sd 2:0:0:0: [sda]
[ 161.463135] Sense Key : No Sense [current]
[ 161.464983] sd 2:0:0:0: [sda]
[ 161.465899] Add. Sense: No additional sense information
[ 161.468211] hv_storvsc vmbus_0_1: cmd 0x41 scsi status 0x2 srb status 0x6
[ 161.475766] sd 2:0:0:0: [sda]
[ 161.476728] Sense Key : No Sense [current]
[ 161.478284] sd 2:0:0:0: [sda]
[ 161.479441] Add. Sense: No additional sense information
...
This happens with a guest running on Windows Server 2012, but happens to
work while running on Windows Server 2008. WRITE_SAME isnt really
supported by both versions, so disable the command usage globally.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Building src.o for a 32 bit system triggers two GCC warnings:
drivers/scsi/aacraid/src.c: In function ‘aac_src_deliver_message’:
drivers/scsi/aacraid/src.c:410:3: warning: right shift count >= width of type [enabled by default]
drivers/scsi/aacraid/src.c:434:2: warning: right shift count >= width of type [enabled by default]
These warnings are caused by a right shift of 32. Use upper_32_bits() to
suppress them.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Mahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Defined SSDID & HW vendor brand strings. Added entries for SSDID within the
function that prints the brand string.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When resetting an ipr adapter, we use scsi_block_requests to
block any new commands from scsi core, and then unblock after
the reset. When hotplug removing an adapter, we shut it down
and go through this same code, but we've seen issues with
scsi_unblock_requests running after the adapter's memory has
been freed. There is really no need to block/unblock when
the adapter is being removed, so this patch skips the
block/unblock and will immediately fail any commands that
happen to make it to queuecommand while the adapter is
being shutdown.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Thierry writes:
"Remove a duplicate implementation of the CEA VIC lookup and move the CEA
and other mode tables to drm_edid.c to make it more difficult to create
duplicates of the tables.
Add some helpers to pack CEA-861/HDMI AVI, audio and SPD infoframes into
binary buffers that can easily be written into hardware registers. A new
helper function makes it easy construct an AVI infoframe from a DRM
display mode.
Convert the Tegra and Radeon drivers to use the new HDMI helpers."
* 'drm/hdmi-for-3.9' of git://anongit.freedesktop.org/tegra/linux:
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
Two regressions fixes from snowboarding land
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Revert hdmi HDP pin checks
drm/i915: Handle untiled planes when computing their offsets
Merge second patch-bomb from Andrew Morton:
- A little DM fix
- the MM queue
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (154 commits)
ksm: allocate roots when needed
mm: cleanup "swapcache" in do_swap_page
mm,ksm: swapoff might need to copy
mm,ksm: FOLL_MIGRATION do migration_entry_wait
ksm: shrink 32-bit rmap_item back to 32 bytes
ksm: treat unstable nid like in stable tree
ksm: add some comments
tmpfs: fix mempolicy object leaks
tmpfs: fix use-after-free of mempolicy object
mm/fadvise.c: drain all pagevecs if POSIX_FADV_DONTNEED fails to discard all pages
mm: export mmu notifier invalidates
mm: accelerate mm_populate() treatment of THP pages
mm: use long type for page counts in mm_populate() and get_user_pages()
mm: accurately document nr_free_*_pages functions with code comments
HWPOISON: change order of error_states[]'s elements
HWPOISON: fix misjudgement of page_action() for errors on mlocked pages
memcg: stop warning on memcg_propagate_kmem
net: change type of virtio_chan->p9_max_pages
vmscan: change type of vm_total_pages to unsigned long
fs/nfsd: change type of max_delegations, nfsd_drc_max_mem and nfsd_drc_mem_used
...
The function names page_xchg_last_nid(), page_last_nid() and
reset_page_last_nid() were judged to be inconsistent so rename them to a
struct_field_op style pattern. As it looked jarring to have
reset_page_mapcount() and page_nid_reset_last() beside each other in
memmap_init_zone(), this patch also renames reset_page_mapcount() to
page_mapcount_reset(). There are others like init_page_count() but as
it is used throughout the arch code a rename would likely cause more
conflicts than it is worth.
[akpm@linux-foundation.org: fix zcache]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On linux, the pages used by kernel could not be migrated. As a result,
if a memory range is used by kernel, it cannot be hot-removed. So if we
want to hot-remove memory, we should prevent kernel from using it.
The way now used to prevent this is specify a memory range by
movablemem_map boot option and set it as ZONE_MOVABLE.
But when the system is booting, memblock will allocate memory, and
reserve the memory for kernel. And before we parse SRAT, and know the
node memory ranges, memblock is working. And it may allocate memory in
ranges to be set as ZONE_MOVABLE. This memory can be used by kernel,
and never be freed.
So, let's parse SRAT before memblock is called first. And it is early
enough.
The first call of memblock_find_in_range_node() is in:
setup_arch()
|-->setup_real_mode()
so, this patch add a function early_parse_srat() to parse SRAT, and call
it before setup_real_mode() is called.
NOTE:
1) early_parse_srat() is called before numa_init(), and has initialized
numa_meminfo. So DO NOT clear numa_nodes_parsed in numa_init() and DO
NOT zero numa_meminfo in numa_init(), otherwise we will lose memory
numa info.
2) I don't know why using count of memory affinities parsed from SRAT
as a return value in original acpi_numa_init(). So I add a static
variable srat_mem_cnt to remember this count and use it as the return
value of the new acpi_numa_init()
[mhocko@suse.cz: parse SRAT before memblock is ready fix]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Wen Congyang <wency@cn.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Jianguo Wu <wujianguo@huawei.com>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Wu Jianguo <wujianguo@huawei.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
