Sparse warned about several functions that were unnecessarily global.
After making them static, discovered that several functions were actually never used.
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Eilon Greenstein <eilong@broadcomo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull Xen update from Konrad Rzeszutek Wilk:
"This has two new ACPI drivers for Xen - a physical CPU offline/online
and a memory hotplug. The way this works is that ACPI kicks the
drivers and they make the appropiate hypercall to the hypervisor to
tell it that there is a new CPU or memory. There also some changes to
the Xen ARM ABIs and couple of fixes. One particularly nasty bug in
the Xen PV spinlock code was fixed by Stefan Bader - and has been
there since the 2.6.32!
Features:
- Xen ACPI memory and CPU hotplug drivers - allowing Xen hypervisor
to be aware of new CPU and new DIMMs
- Cleanups
Bug-fixes:
- Fixes a long-standing bug in the PV spinlock wherein we did not
kick VCPUs that were in a tight loop.
- Fixes in the error paths for the event channel machinery"
Fix up a few semantic conflicts with the ACPI interface changes in
drivers/xen/xen-acpi-{cpu,mem}hotplug.c.
* tag 'stable/for-linus-3.9-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: event channel arrays are xen_ulong_t and not unsigned long
xen: Send spinlock IPI to all waiters
xen: introduce xen_remap, use it instead of ioremap
xen: close evtchn port if binding to irq fails
xen-evtchn: correct comment and error output
xen/tmem: Add missing %s in the printk statement.
xen/acpi: move xen_acpi_get_pxm under CONFIG_XEN_DOM0
xen/acpi: ACPI cpu hotplug
xen/acpi: Move xen_acpi_get_pxm to Xen's acpi.h
xen/stub: driver for CPU hotplug
xen/acpi: ACPI memory hotplug
xen/stub: driver for memory hotplug
xen: implement updated XENMEM_add_to_physmap_range ABI
xen/smp: Move the common CPU init code a bit to prep for PVH patch.
This adds the chromeos_laptop driver. It supports
the Cypress APA SMBUS touchpad as well as the isl29018 i2c ambient
light sensor on the Samsung Series 5 550 Chromebook.
Signed-off-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
The new B series BIOS has version string 43CN46WW. The driver
requires that 2nd and 3rd characters be 'E' and 'T' respectively,
where as the newer BIOS has 'C' and 'N' respectively. Failing to
load the module causes some of the hotkeys to not work.
Before the patch
================
sudo modprobe thinkpad_acpi
FATAL: Error inserting thinkpad_acpi (/lib/modules/3.5.0-15-generic/kernel/drivers/platform/x86/thinkpad_acpi.ko): No such device
After the patch
===============
[44937.265438] thinkpad_acpi: ThinkPad ACPI Extras v0.24
[44937.265445] thinkpad_acpi: http://ibm-acpi.sf.net/
[44937.265449] thinkpad_acpi: ThinkPad BIOS 43CN46WW, EC unknown
[44937.265453] thinkpad_acpi: Lenovo Lenovo B470e, model HuronRiver Platform
[44937.266479] thinkpad_acpi: detected a 8-level brightness capable ThinkPad
[44937.266557] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one
[44937.267846] thinkpad_acpi: Console audio control enabled, mode: monitor (read only)
[44937.268131] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input17
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Tested-by: James Ferguson <james.ferguson@canonical.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Add rfkill support for the GPS radio found in HP laptops (HP Elitebook 2170p and the like)
using the Ericsson F5321/H5321 Mobile Broadband Module.
Signed-off-by: Viliam Trepák <trepo@netcomga.sk>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Found another Lenovo ideapad S205 the product name is 1038DPG, it has
a 0x78 EC register exposes the state of wifi hardware switch on the machine.
So, add this patch to support Lenovo ideapad S205-1038DPG wifi hardware
switch in acer-wmi driver.
Evidently the Ideapad S205 is just a model name on the market, but they have
totally different product name in DMI table.
Reference: bko#43007
https://bugzilla.kernel.org/show_bug.cgi?id=43007
Tested-by: Colin <colin.newell@gmail.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Found another Lenovo ideapad S205 the product name is 10382JG, it has
a 0x78 EC register exposes the state of wifi hardware switch on the machine.
So, add this patch to support Lenovo ideapad S205-10382JG wifi hardware
switch in acer-wmi driver.
Evidently the Ideapad S205 is just a model name on the market, but they have
totally different product name in DMI table.
Reference: bko#43007
https://bugzilla.kernel.org/show_bug.cgi?id=43007
Tested-by: Ivo Anjo <knuckles@gmail.com>
Cc: Carlos Corbacho <carlos@strangeworlds.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
For machines with AMD graphic chips, it will send out WMI event and ACPI
interrupt at the same time while hitting the hotkey. BIOS will notify the
system the next display output mode throught WMI event code, so that
windows' application can show an OSD to tell the user which mode will be
taken effect. User can hit the display toggle key many times within 2
seconds to choose the mode they want. After 2 seconds, WMI dirver should
send a WMIMethod(SDSP) command to tell the BIOS which mode the user chose.
And then BIOS will raise another ACPI interrupt to tell the system to
really switch the display mode.
In Linux desktop, we don't have this kind of OSD to let users to choose
the mode they want, so we don't need to call WMIMethod(SDSP) to have
another ACPI interrupt. To simplify the problem, we just have to ignore
the WMI event, and let the first ACPI interrupt to send out the key event.
For the need, here comes another quirk to add machines with this kind of
behavior. When the WMI driver receives the display toggle WMI event, and
found the machin is in the list, it will do nothing and let ACPI video
driver to report the key event.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Add MSI Wind support to msi-wmi driver. MSI Wind has different GUID for
key events, different WMI key scan codes, it does not need filtering
consecutive identical events and it does not support backlight control
via MSIWMI_BIOS_GUID WMI. Tested on MSI Wind U100.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Introduced quirk_last_pressed variable that would indicate if
last_pressed is used or not. Also converted last_pressed to simple
variable in order to allow keymap to be non-contiguous.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Introduced function msi_wmi_backlight_setup() that initializes backlight
device. Made driver load and work if only one WMI (only for hotkeys or
only for backlight) is present.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Use enums for consecutive scancodes, rename key names from MSI_WMI_* to
MSI_KEY_* and use tabs for whitespace in msi_wmi_keymap.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Acked-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
It seems that existing brightness control works only for old EC models.
On newer ones auto_brightness access always timeouts and lcd_level
always shows 0. So disable brightness control for new EC models. It
works fine with ACPI video driver anyway.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Add MSI Wind U90/U100 to DMI table and add some missing EC features
support such as basic fan control, turbo and ECO modes and touchpad
state. Tested on MSI Wind U100.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
This patch introduced a quirk_entry struct, then we merged all quirk
tables to msi_dmi_table. Then we can more easily to set different quirk
attributes for different machine.
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Changed this patch so that it could be applied before MSI Wind U100
support patch. Changed rfkill logic for ec_read_only quirk support.
Removed delays if ec_delay = false.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Acked-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Assign initial value to variable in order to prevent gcc warning about
uninitialized variable.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
For those machines with wapf=4, BIOS won't update the wireless LED,
since wapf=4 means user application will take in chage of the wifi and bt.
So, we have to update wlan LED status explicitly.
But I found there is another wireless LED bug in launchpad and which is
not in the wapf=4 quirk.
So, it might be better to set wireless LED status explicitly for all
machines.
BugLink: https://launchpad.net/bugs/901105
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Rework the driver to parse the device tree
directly into struct sdhci_tegra.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Many MMC capability flags are platform-dependent and are traditionally set
in platform data. With DT often each such capability requires a special
binding. Add bindings for MMC_CAP_SD_HIGHSPEED, MMC_CAP_MMC_HIGHSPEED,
MMC_CAP_POWER_OFF_CARD and MMC_CAP_SDIO_IRQ capabilities. Also add code to
DT parser to look up "keep-power-in-suspend" and "enable-sdio-wakeup"
bindings and set MMC_PM_KEEP_POWER and MMC_PM_WAKE_SDIO_IRQ respectively,
if found.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some SD/MMC interfaces use 2 power regulators: one to power the card itself
(Vcc) and another one to pull signal lines up (VccQ). In case of eMMC and
UHS SD cards the regulators also have to be configured to supply different
voltages. The preferred order of turning supply power on and off is to
turn Vcc first on and last off.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use managed allocations to get memory, clock and interrupts . This
significantly simplifies clean up paths.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The struct sh_mobile_sdhi_info::pdata field was only used for platform-
based card detection and isn't used anymore since the migration to GPIO-
based MMC slot functions. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add parsing of common and driver-specific DT bindings to the tmio-mmc
MMC host driver and the sh_mobile_sdhi interface layer.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use mmc_of_parse() to get interface capability flags and used GPIOs from
device-tree bindings.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC defines a number of standard DT bindings. Having each driver parse
them individually adds code redundancy and is error prone. Provide a
standard function to unify the parsing. After all drivers are converted
to using it instead of their own parsers, this function can be integrated
into mmc_alloc_host().
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
tmio-mmc platform flags can be set by various means, including caller
drivers and device-tree bindings, therefore it is better to only check
them in the tmio-mmc driver proper, not in caller drivers themselves.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
3714f4315354 ("mmc: sdhci: update signal voltage switch code") changed the
type of the second parameter of sdhci_do_start_signal_voltage_switch(),
from "struct mmc_ios *ios" to "int signal_voltage" which causes the
following build warning:
drivers/mmc/host/sdhci.c:2044:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/mmc/host/sdhci.c:2044:2: warning: (near initialization for 'sdhci_ops.start_signal_voltage_switch') [enabled by default]
Use the previous type so that it matches the start_signal_voltage_switch()
definition from host.h.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Johan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some regulators don't report any voltage values, so checking supported
voltage range results in disabling all SDHCI_CAN_VDD_* flags and
registration failure. This patch finally provides a correct fix for the
registration of SDHCI driver with all possible voltage regulators:
dummy, fixed and regulated without using regulator_count_voltages()
hacks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK does basically the same as
implementing struct sdhci_ops .get_timeout_clock, so simply set that
quirk and remove the custom code to simplify the driver.
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch supports packed write command of eMMC4.5 devices. Several
writes can be grouped in packed command and all data of the individual
commands can be sent in a single transfer on the bus. Large amounts of
data in one transfer rather than several data of small size are
effective for eMMC write internally. As a result, packed command help
write throughput be improved. The following tables show the results
of packed write.
Type A:
test none | packed
iozone 25.8 | 31
tiotest 27.6 | 31.2
lmdd 31.2 | 35.4
Type B:
test none | packed
iozone 44.1 | 51.1
tiotest 47.9 | 52.5
lmdd 51.6 | 59.2
Type C:
test none | packed
iozone 19.5 | 32
tiotest 19.9 | 34.5
lmdd 22.8 | 40.7
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds packed command feature of eMMC4.5. The maximum number
for packing read (or write) is offered and exception event relevant to
packed command which is used for error handling is enabled. If host
wants to use this feature, MMC_CAP2_PACKED_CMD should be set.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Several new models of readers use different way to select driving
capability (a necessary adjustment along with voltage change). Removing
this from device-independent rtsx_pci_sdmmc module. It will be implemented
in device-depend calls encapsulated by rtsx_pci_switch_output_voltage().
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Reviewed-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_regulator_set_ocr() depends on the ability of regulator to change the
voltage value. When regulator cannot change its voltage output, some code
is skipped to avoid reporting false errors on some boards, which use MMC
hosts with fixed regulators (e.g. Samsung Goni and UniversalC210 boards).
This patch replaces a hacky workaround based on regulator_count_voltages()
value with the correct call to recently introduced
regulator_can_change_voltage() function in regulators core.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is derived from:
"mmc: fix async request mechanism for sequential read scenarios".
According as async transfer, a request is handled with twice mmc_start_req.
When the card is removed, the request is actually not issued in the first
mmc_start_req [__mmc_start_data_req]. And then mmc_wait_for_data_req_done
will come in the next mmc_start_req. But there is no event for completions.
wake_up_interruptible is needed in __mmc_start_data_req for the case of
removed card.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Konstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
4d55c5a1 ("mmc: sdhci: enable preset value after uhs initialization")
added preset value support and enabled it by default during sd card init.
Below are the enhancements introduced by this patch:
1. In current code, preset value is enabled after setting clock finished,
which means the clock is manually set by driver firstly and then suddenly
switched to preset value at this point. So the first setting is useless
and unnecessary. What's more, the first clock setting may differ from the
preset one. The better way is enable preset value just after switch to
UHS mode so the preset value can take effect immediately. So move preset
value enable from mmc_sd_init_card to sdhci_set_ios which will be called
during set timing.
2. In current code, preset value is disabled at the beginning of
mmc_attach_sd. It's too late since low freq (400khz) should be set in
mmc_power_up. So move preset value disable to sdhci_set_ios which will
be called during power up.
3. host->clock and ios->drv_type should also be updated according to the
preset value if it's enabled. Current code missed this.
4. This patch also introduce a quirk to disable preset value in case
preset value doesn't work.
This patch has been verified on sdhci-pxav3 platform with both preset
enabled and disabled.
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When irq_of_parse_and_map() returns an error, it does as zero. But in
mmc_spi_get_pdata(), the error return case is compared against NO_IRQ.
This might work where NO_IRQ is zero (defaults to zero when undefined,
as on MIPS) but not where NO_IRQ is different, e.g. on ARM where it's -1.
This patch changes to comparison with 0 which is the error return value
of irq_of_parse_and_map().
Tested on ARM that mmc_spi is working now.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Quite a few drivers have a implementation of the get_timeout_clock
callback which simply returns the result of clk_get_rate on the device's
clock. This patch adds a common implementation of this to the sdhci-pltfm
module and replaces all custom implementations with the common one.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
