The GIC requires some extra opaque arguments to set the IRQ type and flags.
Convert the DTs to using the common defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.
Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DMA engine for the A10/A20 and derivatives require an opaque extra
argument.
Add a dt-bindings header, and convert the device trees to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Replace the various raw GPIO flags by their definition in the common
dt-bindings header.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CSQ CS908 is an A31s based top-set box, with 1G RAM, 8G NAND,
rtl8188etv usb wifi, 2 USB A receptacles (1 connected through the OTG
controller), ethernet, 3.5 mm jack with a/v out and hdmi out.
Note it has no sdcard slot and therefore can only be fel booted.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a dtsi file for A31s based boards.
Since the A31s is the same die as the A31 in a different package, this dtsi
simply includes sun6i-a31.dtsi and then overrides the pinctrl compatible to
reflect the different package, everything else is identical.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Only SPI0 is enabled, as the schematic denotes it as the only SPI bus,
while other pins are reserved for different peripherals.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These are based on the available SPI configurations of Cubieboard,
Olimex LIME, and PcDuino. There is no pin group for SPI3, as all the
boards seem to use those pins for EMAC.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Hummingbird A31 board, the RTL8211E ethernet phy has its reset
line connect to a gpio pin, instead of floating like on other boards.
Add the stmmac properties for describing the reset gpio.
The reset delays were taken from the RTL8211E datasheet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. This can be avoided by letting the display frontend engine
do the dma from memory, and then letting it feed the data directly into
the backend unmodified, as the frontend does have deep enough fifo-s.
Note since u-boot-v2015.01 has been released using the de_be0-lcd0-hdmi
pipeline on sun4i, we need to keep that one around too (unfortunately).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It was accidentally left (& copied & pasted all around) from our
experiments with gpio-keys-polled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Luxul XWC-1000 is a controller device based on BCM4708 SoC. The only
unusual thing in its DTS file is "ubi" partition on NAND flash.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These add device tree entry for qspi device on dra72-evm.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Vybrid, all peripherals are numbered starting with zero,
including the GPIO and PORT module. However, the labels of the
corresponding device tree nodes start with one, which is confusing.
Fix that by renaming the labels of the gpio nodes in the device
tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently PWM functionality is broken on mx25 due to the wrong assignment of the
PWM "per" clock.
According to Documentation/devicetree/bindings/clock/imx25-clock.txt:
pwm_ipg_per 52
,so update the pwm "per" to use 'pwm_ipg_per' instead of 'per10' clock.
With this change PWM can work fine on mx25.
Cc: <stable@vger.kernel.org>
Reported-by: Carlos Soto <csotoalonso@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Merge "Second Round of Renesas ARM Based SoC DT Cleanups for v3.20" from Simon
Horman:
Second Round of Renesas ARM Based SoC DT Cleanups for v3.20
* Tidy up #sound-dai-cells settings
* Drop "renesas,rcar_sound" compatible value
* tag 'renesas-dt-cleanups2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: tidyup #sound-dai-cells settings
ARM: shmobile: r8a7790: tidyup #sound-dai-cells settings
ARM: shmobile: r8a7791 dtsi: Drop "renesas,rcar_sound" compatible value
ARM: shmobile: r8a7790 dtsi: Drop "renesas,rcar_sound" compatible value
Signed-off-by: Olof Johansson <olof@lixom.net>
The file is roughly sorted alphabetically (with some exceptions where
old options have been split in two), so alphascale should go at the
top instead of at the bottom.
Also linewrap like other entries have been lately.
Signed-off-by: Olof Johansson <olof@lixom.net>
for now it is wary basic SoC description with most important IPs needed
to make this device work
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Urgent omap4 legacy interrupt regression fix for v3.19-rc series" from
Tony Lindgren:
A rather urgent pull request to fix omap4 legacy interrupts.
The legacy interrupts on omap4 got broken when gic got changed to
use irq_domain_add_linear() instead of the irq_domain_add_legacy(). We
still have the hardcoded legacy IRQ numbers in use in several places,
most notably the in the legacy DMA. It took a while to figure out
what the problem was and how it should be fixed for the -rc series.
Also include is a regression fix for the dra7 dwc3 suspend.
* tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Work around hardcoded interrupts
arm: boot: dts: dra7: enable dwc3 suspend PHY quirk
Signed-off-by: Olof Johansson <olof@lixom.net>
The commit (3d125f9c91) cause i.MX6SX sdb enet cannot work. The cause is
the commit add mdio node with un-correct phy address.
The patch just correct i.MX6sx sdb board enet phy address.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows booting the device with basic functionality.
Note that at least on my revision c board the DDR3 does
not seem to work properly and only some of the memory
can be reliably used.
Also, the mainline u-boot does not seem to properly
initialize the ethernet, so I've been using the old TI
u-boot at:
http://arago-project.org/git/projects/?p=u-boot-omap3.git;a=summary
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clocks on dm816x are a bit different from the other omap
variants. The clocks are sourced from a FAPLL (Flying Adder PLL)
unlike on other omaps. Other than that, it's a similar setup
to am33xx with extra muxes and dividers that can be defined
as existing component clocks.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "at91: dt for 3.20 #1" from Nicolas Ferre:
First batch of DT changes for 3.20:
- little typo and a LED declared
- addition of the Special Function Registers (SFR) + its binding
- RTC & SRAM nodes
- the at91sam9xe has its own .dtsi now. Not combined with at91sam9260 anymore
- addition of the Image Sensor Interface (ISI) DT part and supported sensors
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: dts: sama5d3: add ov2640 camera sensor support
ARM: at91: dts: sama5d3: change name of pinctrl of ISI_MCK
ARM: at91: dts: sama5d3: change name of pinctrl_isi_{power,reset}
ARM: at91: dts: sama5d3: move the isi mck pin to mb
ARM: at91: dts: sama5d3: add missing pins of isi
ARM: at91: dts: sama5d3: split isi pinctrl
ARM: at91: dts: sama5d3: add isi clock
ARM: at91/dt: ethernut5: use at91sam9xe.dtsi
ARM: at91/dt: Add a dtsi for at91sam9xe
ARM: at91/dt: add SRAM nodes
ARM: at91/dt: at91rm9200ek: enable RTC
ARM: at91/dt: rm9200: add RTC node
ARM: at91/dt: at91sam9n12: Add RTC node
ARM: at91: sama5d4: Add SFR
ARM: at91: sama5d3: Add SFR
ARM: at91: Add Special Function Registers binding documentation
ARM: at91/dt: sam9263: Fix typo: ac91_clk -> ac97_clk
ARM: at91/dt: sama5d3: enable D2 as the heartbeat LED
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "CSR atlas7 init dts for 3.20" from Barry Song:
Drop Marco and add init dts stuff for Atlas7
CSR Marco SoC has never shipped to customers that could be interested
in mainline support. and new Atlas7 is a replacement SoC that is in
development.
So we drop Marco dts stuff, and add dts stuff for Atlas7.
* tag 'atlas7-init-dts-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux:
ARM: dts: add init dts file for CSR atlas7 SoC
ARM: dts: drop MARCO platform DT stuff
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on our fixes branch for a while, so this batch is
unfortunately on the large side.
A lot of these are tweaks and fixes to device trees, fixing various
bugs around clocks, reg ranges, etc. There's also a few defconfig
updates (which are on the late side, no more of those).
All in all the diffstat is bigger than ideal at this time, but nothing
in here seems particularly risky"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
reset: sunxi: fix spinlock initialization
ARM: dts: disable CCI on exynos5420 based arndale-octa
drivers: bus: check cci device tree node status
ARM: rockchip: disable jtag/sdmmc autoswitching on rk3288
ARM: nomadik: fix up leftover device tree pins
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
ARM: exynos_defconfig: Enable LM90 driver
ARM: exynos_defconfig: Enable options for display panel support
arm: dts: Use pmu_system_controller phandle for dp phy
ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
...
The arndale-octa board was giving "imprecise external aborts" during
boot-up with MCPM enabled. CCI enablement of the boot cluster was found
to be the cause of these aborts (possibly because the secure f/w was not
allowing it). Hence, disable CCI for the arndale-octa board.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "at91: fixes for 3.19 #1 (ter)" from Nicolas Ferre:
First fixes batch for AT91 on 3.19:
- fix some DT entries
- correct clock entry for the at91sam9263 LCD
- add a phy_fixup for Eth1 on sama5d4
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: berlin: Fixes for v3.19 (round 1)" from Sebastian Hesselbarth:
Marvell Berlin fixes for v3.19 round 1:
- SDHCI DT fixes for BG2Q and BG2Q reference board
- BG2Q SM GPIO DT node relocation
* tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
Signed-off-by: Olof Johansson <olof@lixom.net>
We altered the device tree bindings for the Nomadik family of
pin controllers to be standard, this file was merged out-of-order
so we missed fixing this. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "omap fixes against v3.19-rc1" from Tony Lindgren:
Fixes for omaps mostly to deal with dra7 timer issues
and hypervisor mode. The other fixes are minor fixes for
various boards. The summary of the fixes is:
- Fix real-time counter rate typos for some frequencies
- Fix counter frequency drift for am572x
- Fix booting of secondary CPU in HYP mode
- Fix n900 board name for legacy user space
- Fix cpufreq in omap2plus_defconfig after Kconfig change
- Fix dra7 qspi partitions
And also, let's re-enable smc91x on some n900 boards that
we have sitting in a few test boot systems after the boot
loader dependencies got fixed.
* tag 'omap-for-v3.19/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
ARM: OMAP2+: Fix n900 board name for legacy user space
ARM: omap5/dra7xx: Enable booting secondary CPU in HYP mode
ARM: dra7xx: Fix counter frequency drift for AM572x errata i856
ARM: omap5/dra7xx: Fix frequency typos
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: fixes for 3.19" from Shawn Guo:
The i.MX fixes for 3.19:
- One fix for incorrect i.MX25 SPI1 clock assignment in device tree,
which causes system hang when accessing SPI1.
- Correct i.MX6SX QSPI parent clock configuration to fix a kernel Oops.
- Fix ULPI PHY reset modelling on imx51-babbage board to remove the
dependency on bootloader for USB3317 ULPI PHY reset.
- Correct video divider setting on i.MX6Q rev T0 1.0 to fix the issue
that HDMI is not working at high resolution on T0 1.0.
- One incremental fix for CODA960 VPU enabling in device tree to
correct interrupt order.
- LS1021A SCFG block works in BE mode, add device tree property
big-endian to make it right.
* tag 'imx-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: imx6sx: Set PLL2 as parent of QSPI clocks
ARM: dts: imx25: Fix the SPI1 clocks
ARM: clk-imx6q: fix video divider for rev T0 1.0
ARM: dts: imx6qdl: Fix CODA960 interrupt order
ARM: ls1021a: dtsi: add 'big-endian' property for scfg node
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: rockchip: dts fix for 3.19" from Heiko Stübner:
Increase drive-strength to sdmmc pins on rk3288-evb to fix
an issue with the fixed highspeed card detection.
* tag 'v3.19-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: bump sd card pin drive strength up on rk3288-evb
Signed-off-by: Olof Johansson <olof@lixom.net>
