From the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Required for dependencies in following patches
* branch 'mellanox/mlx5-next':
net/mlx5: Add ability to read and write ECE options
net/mlx5: Add support for RDMA TX FT headers modifying
net/mlx5: Move iseg access helper routines close to mlx5_core driver
net/mlx5: Cleanup mlx5_ifc_fte_match_set_misc2_bits
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
As explained in other commits before (b9cd75e668 and 87b0f983f6),
ocelot switches have a single egress-untagged VLAN per port, and the
driver would deny adding a second one while an egress-untagged VLAN
already exists.
But on the CPU port (where the VLAN configuration is implicit, because
there is no net device for the bridge to control), the DSA core attempts
to add a VLAN using the same flags as were used for the front-panel
port. This would make adding any untagged VLAN fail due to the CPU port
rejecting the configuration:
bridge vlan add dev swp0 vid 100 pvid untagged
[ 1865.854253] mscc_felix 0000:00:00.5: Port already has a native VLAN: 1
[ 1865.860824] mscc_felix 0000:00:00.5: Failed to add VLAN 100 to port 5: -16
(note that port 5 is the CPU port and not the front-panel swp0).
So this hardware will send all VLANs as tagged towards the CPU.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot core library is written with the idea in mind that the VLAN
table is populated by the bridge. Otherwise, not even a sane default
pvid is provided: in standalone mode, the default pvid is 0, and the
core expects the bridge layer to change it to 1.
So without this patch, the VLAN table is completely empty at the end of
the commands below, and traffic is broken as a result:
ip link add dev br0 type bridge vlan_filtering 0 && ip link set dev br0 up
for eth in $(ls /sys/bus/pci/devices/0000\:00\:00.5/net/); do
ip link set dev $eth master br0
ip link set dev $eth up
done
ip link set dev br0 type bridge vlan_filtering 1
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple large ecmp group nexthop selftests to cover
the remnant fixed by d69100b8ee.
The tests create 100 x32 ecmp groups of ipv4 and ipv6 and then
dump them. On kernels without the fix, they will fail due
to data remnant during the dump.
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang-10 and clang-11 run into a corner case of the register
allocator on 32-bit ARM, leading to excessive stack usage from
register spilling:
net/bridge/br_multicast.c:2422:6: error: stack frame size of 1472 bytes in function 'br_multicast_get_stats' [-Werror,-Wframe-larger-than=]
Work around this by marking one of the internal functions as
noinline_for_stack.
Link: https://bugs.llvm.org/show_bug.cgi?id=45802#c9
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be a race between nvme_reap_pending_cqes() and nvme_poll(), e.g.,
when doing live reset while polling the nvme device.
CPU X CPU Y
nvme_poll()
nvme_dev_disable()
-> nvme_stop_queues()
-> nvme_suspend_io_queues()
-> nvme_suspend_queue()
-> spin_lock(&nvmeq->cq_poll_lock);
-> nvme_reap_pending_cqes()
-> nvme_process_cq() -> nvme_process_cq()
In the above scenario, the nvme_process_cq() for the same queue may be
running on both CPU X and CPU Y concurrently.
It is much more easier to reproduce the issue when CONFIG_PREEMPT is
enabled in kernel. When CONFIG_PREEMPT is disabled, it would take longer
time for nvme_stop_queues()-->blk_mq_quiesce_queue() to wait for grace
period.
This patch protects nvme_process_cq() with nvmeq->cq_poll_lock in
nvme_reap_pending_cqes().
Fixes: fa46c6fb5d ("nvme/pci: move cqe check after device shutdown")
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Without CONFIG_PM, the compiler warns about two unused functions:
drivers/net/ethernet/mediatek/mtk_star_emac.c:1472:12: error: unused function 'mtk_star_suspend' [-Werror,-Wunused-function]
drivers/net/ethernet/mediatek/mtk_star_emac.c:1488:12: error: unused function 'mtk_star_resume' [-Werror,-Wunused-function]
Mark these as __maybe_unused.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks the MRP netlink interface. Before, each attribute
represented a binary structure which made it hard to be extended.
Therefore update the MRP netlink interface such that each existing
attribute to be a nested attribute which contains the fields of the
binary structures.
In this way the MRP netlink interface can be extended without breaking
the backwards compatibility. It is also using strict checking for
attributes under the MRP top attribute.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable new_pvid is being assigned with a value that is never read,
the following if statement updates new_pvid with a new value in both
of the if paths. The assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma_addr field in desc_data must not be overwritten until after the
new skb is mapped. Currently we do replace it with uninitialized value
in error path. This change fixes it by moving the assignment before the
label to which we jump after mapping or allocation errors.
Fixes: 8c7bd5a454 ("net: ethernet: mtk-star-emac: new driver")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com> # build
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer br_dev is being initialized with a value that is never read
and is being updated with a new value later on. The initialization
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns:
net/ipv4/nexthop.c:841:30: warning: implicit conversion from enumeration
type 'enum nexthop_event_type' to different enumeration type 'enum
fib_event_type' [-Wenum-conversion]
call_nexthop_notifiers(net, NEXTHOP_EVENT_DEL, nh);
~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~
1 warning generated.
Use the right type for event_type so that clang does not warn.
Fixes: 8590ceedb7 ("nexthop: add support for notifiers")
Link: https://github.com/ClangBuiltLinux/linux/issues/1038
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The accept(2) is an "input" socket interface, so we should use
SO_RCVTIMEO instead of SO_SNDTIMEO to set the timeout.
So this patch replace sock_sndtimeo() with sock_rcvtimeo() to
use the right timeout in the vsock_accept().
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this change the correct value for the used counter is calculated
but not stored nor, therefore, propagated to user-space. In use-cases such
as OVS use-case at least this results in active flows being removed from
the hardware datapath. Which results in both unnecessary flow tear-down
and setup, and packet processing on the host.
This patch addresses the problem by saving the calculated used value
which allows the value to propagate to user-space.
Found by inspection.
Fixes: aa6ce2ea0c ("nfp: flower: support stats update for merge flows")
Signed-off-by: Heinrich Kuhn <heinrich.kuhn@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull fanotify FAN_DIR_MODIFY disabling from Jan Kara:
"A single patch that disables FAN_DIR_MODIFY support that was merged in
this merge window.
When discussing further functionality we realized it may be more
logical to guard it with a feature flag or to call things slightly
differently (or maybe not) so let's not set the API in stone for now."
* tag 'fsnotify_for_v5.7-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: turn off support for FAN_DIR_MODIFY
Pull cgroup fixes from Tejun Heo:
- Reverted stricter synchronization for cgroup recursive stats which
was prepping it for event counter usage which never got merged. The
change was causing performation regressions in some cases.
- Restore bpf-based device-cgroup operation even when cgroup1 device
cgroup is disabled.
- An out-param init fix.
* 'for-5.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
device_cgroup: Cleanup cgroup eBPF device filter code
xattr: fix uninitialized out-param
Revert "cgroup: Add memory barriers to plug cgroup_rstat_updated() race window"
Instead of calling kvm_event_needs_reinjection, track its
future return value in a variable. This will be useful in
the next patch.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
L2 guest hang is observed after 'exit_required' was dropped and nSVM
switched to check_nested_events() completely. The hang is a busy loop when
e.g. KVM is emulating an instruction (e.g. L2 is accessing MMIO space and
we drop to userspace). After nested_svm_vmexit() and when L1 is doing VMRUN
nested guest's RIP is not advanced so KVM goes into emulating the same
instruction which caused nested_svm_vmexit() and the loop continues.
nested_svm_vmexit() is not new, however, with check_nested_events() we're
now calling it later than before. In case by that time KVM has modified
register state we may pick stale values from VMCB when trying to save
nested guest state to nested VMCB.
nVMX code handles this case correctly: sync_vmcs02_to_vmcs12() called from
nested_vmx_vmexit() does e.g 'vmcs12->guest_rip = kvm_rip_read(vcpu)' and
this ensures KVM-made modifications are preserved. Do the same for nSVM.
Generally, nested_vmx_vmexit()/nested_svm_vmexit() need to pick up all
nested guest state modifications done by KVM after vmexit. It would be
great to find a way to express this in a way which would not require to
manually track these changes, e.g. nested_{vmcb,vmcs}_get_field().
Co-debugged-with: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200527090102.220647-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Restoring the ASID from the hsave area on VMEXIT is wrong, because its
value depends on the handling of TLB flushes. Just skipping the field in
copy_vmcb_control_area will do.
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Async page faults have to be trapped in the host (L1 in this case),
since the APF reason was passed from L0 to L1 and stored in the L1 APF
data page. This was completely reversed: the page faults were passed
to the guest, a L2 hypervisor.
Cc: stable@vger.kernel.org
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is a bad indentation in next&queue branch. The patch looks like
fixes nothing though it fixes the indentation.
Before fixing:
if (!handle_fastpath_set_x2apic_icr_irqoff(vcpu, data)) {
kvm_skip_emulated_instruction(vcpu);
ret = EXIT_FASTPATH_EXIT_HANDLED;
}
break;
case MSR_IA32_TSCDEADLINE:
After fixing:
if (!handle_fastpath_set_x2apic_icr_irqoff(vcpu, data)) {
kvm_skip_emulated_instruction(vcpu);
ret = EXIT_FASTPATH_EXIT_HANDLED;
}
break;
case MSR_IA32_TSCDEADLINE:
Signed-off-by: Haiwei Li <lihaiwei@tencent.com>
Message-Id: <2f78457e-f3a7-3bc9-e237-3132ee87f71e@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The second "/* fall through */" in rmode_exception() makes code harder to
read. Replace it with "return" to indicate they are different cases, only
the #DB and #BP check vcpu->guest_debug, while others don't care. And this
also improves the readability.
Suggested-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Message-Id: <1582080348-20827-1-git-send-email-linmiaohe@huawei.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Take a u32 for the index in has_emulated_msr() to match hardware, which
treats MSR indices as unsigned 32-bit values. Functionally, taking a
signed int doesn't cause problems with the current code base, but could
theoretically cause problems with 32-bit KVM, e.g. if the index were
checked via a less-than statement, which would evaluate incorrectly for
MSR indices with bit 31 set.
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200218234012.7110-3-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Remove unnecessary brackets from a case statement that unintentionally
encapsulates unrelated case statements in the same switch statement.
While technically legal and functionally correct syntax, the brackets
are visually confusing and potentially dangerous, e.g. the last of the
encapsulated case statements has an undocumented fall-through that isn't
flagged by compilers due the encapsulation.
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200218234012.7110-2-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The migration functionality was left incomplete in commit 5ef8acbdd6
("KVM: nVMX: Emulate MTF when performing instruction emulation", 2020-02-23),
fix it.
Fixes: 5ef8acbdd6 ("KVM: nVMX: Emulate MTF when performing instruction emulation")
Cc: stable@vger.kernel.org
Reviewed-by: Oliver Upton <oupton@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We can simply look at bits 52-53 to identify MMIO entries in KVM's page
tables. Therefore, there is no need to pass a mask to kvm_mmu_set_mmio_spte_mask.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This msr is only available when the host supports WAITPKG feature.
This breaks a nested guest, if the L1 hypervisor is set to ignore
unknown msrs, because the only other safety check that the
kernel does is that it attempts to read the msr and
rejects it if it gets an exception.
Cc: stable@vger.kernel.org
Fixes: 6e3ba4abce ("KVM: vmx: Emulate MSR IA32_UMWAIT_CONTROL")
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200523161455.3940-3-mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Even though we might not allow the guest to use WAITPKG's new
instructions, we should tell KVM that the feature is supported by the
host CPU.
Note that vmx_waitpkg_supported checks that WAITPKG _can_ be set in
secondary execution controls as specified by VMX capability MSR, rather
that we actually enable it for a guest.
Cc: stable@vger.kernel.org
Fixes: e69e72faa3 ("KVM: x86: Add support for user wait instructions")
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200523161455.3940-2-mlevitsk@redhat.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Set the mmio_value to '0' instead of simply clearing the present bit to
squash a benign warning in kvm_mmu_set_mmio_spte_mask() that complains
about the mmio_value overlapping the lower GFN mask on systems with 52
bits of PA space.
Opportunistically clean up the code and comments.
Cc: stable@vger.kernel.org
Fixes: d43e2675e9 ("KVM: x86: only do L1TF workaround on affected processors")
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <20200527084909.23492-1-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
FAN_DIR_MODIFY has been enabled by commit 44d705b037 ("fanotify:
report name info for FAN_DIR_MODIFY event") in 5.7-rc1. Now we are
planning further extensions to the fanotify API and during that we
realized that FAN_DIR_MODIFY may behave slightly differently to be more
consistent with extensions we plan. So until we finalize these
extensions, let's not bind our hands with exposing FAN_DIR_MODIFY to
userland.
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Pull execve fix from Eric Biederman:
"While working on my exec cleanups I found a bug in exec that winds up
miscomputing the ambient credentials during exec. Andy appears to have
to been confused as to why credentials are computed for both the
script and the interpreter
From the original patch description:
[3] Linux very confusingly processes both the script and the
interpreter if applicable, for reasons that elude me. The results
from thinking about a script's file capabilities and/or setuid
bits are mostly discarded.
The only value in struct cred that gets changed in cap_bprm_set_creds
that I could find that might persist between the script and the
interpreter was cap_ambient. Which is fixed with this trivial change"
* 'exec-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
exec: Always set cap_ambient in cap_bprm_set_creds
Building this driver with "clang -O3" produces a link error
after the compiler partially unrolls the loop and 256ms
becomes a compile-time constant that triggers the check
in udelay():
ld.lld: error: undefined symbol: __bad_udelay
>>> referenced by applesmc.c
>>> hwmon/applesmc.o:(read_smc) in archive drivers/built-in.a
I can see no reason against using a sleeping function here,
as no part of the driver runs in atomic context, so instead use
usleep_range() with a wide range and use jiffies for the
end condition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200527135207.1118624-1-arnd@arndb.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Hibernation via snapshot device requires write permission to the swap
block device, the one that more often (but not necessarily) is used to
store the hibernation image.
With this patch, such permissions are granted iff:
1) snapshot device config option is enabled
2) swap partition is used as resume device
In other circumstances the swap device is not writable from userspace.
In order to achieve this, every write attempt to a swap device is
checked against the device configured as part of the uswsusp API [0]
using a pointer to the inode struct in memory. If the swap device being
written was not configured for resuming, the write request is denied.
NOTE: this implementation works only for swap block devices, where the
inode configured by swapon (which sets S_SWAPFILE) is the same used
by SNAPSHOT_SET_SWAP_AREA.
In case of swap file, SNAPSHOT_SET_SWAP_AREA indeed receives the inode
of the block device containing the filesystem where the swap file is
located (+ offset in it) which is never passed to swapon and then has
not set S_SWAPFILE.
As result, the swap file itself (as a file) has never an option to be
written from userspace. Instead it remains writable if accessed directly
from the containing block device, which is always writeable from root.
[0] Documentation/power/userland-swsusp.rst
v2:
- rename is_hibernate_snapshot_dev() to is_hibernate_resume_dev()
- fix description so to correctly refer to the resume device
Signed-off-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit ea6f3af4c5 ("ACPI: GED: add support for _Exx / _Lxx handler
methods") added a reference to the 'triggering' field of either the
normal or the extended ACPI IRQ resource struct, but inadvertently used
the wrong pointer in the latter case. Note that both pointers refer to the
same union, and the 'triggering' field appears at the same offset in both
struct types, so it currently happens to work by accident. But let's fix
it nonetheless
Fixes: ea6f3af4c5 ("ACPI: GED: add support for _Exx / _Lxx handler methods")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When writing to a delalloc region in the data fork, commit the new
allocations (of the da reservation) as unwritten so that the mappings
are only marked written once writeback completes successfully. This
fixes the problem of stale data exposure if the system goes down during
targeted writeback of a specific region of a file, as tested by
generic/042.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Refactor xfs_iomap_prealloc_size to be the function that dynamically
computes the per-file preallocation size by moving the allocsize= case
to the caller. Break up the huge comment preceding the function to
annotate the relevant parts of the code, and remove the impossible
check_writeio case.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
When we're estimating a new speculative preallocation length for an
extending write, we should walk backwards through the extent list to
determine the number of number of blocks that are physically and
logically contiguous with the write offset, and use that as an input to
the preallocation size computation.
This way, preallocation length is truly measured by the effectiveness of
the allocator in giving us contiguous allocations without being
influenced by the state of a given extent. This fixes both the problem
where ZERO_RANGE within an EOF can reduce preallocation, and prevents
the unnecessary shrinkage of preallocation when delalloc extents are
turned into unwritten extents.
This was found as a regression in xfs/014 after changing delalloc writes
to create unwritten extents during writeback.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
During writeback, it's possible for the quota block reservation in
xfs_iomap_write_unwritten to fail with EDQUOT because we hit the quota
limit. This causes writeback errors for data that was already written
to disk, when it's not even guaranteed that the bmbt will expand to
exceed the quota limit. Irritatingly, this condition is reported to
userspace as EIO by fsync, which is confusing.
We wrote the data, so allow the reservation. That might put us slightly
above the hard limit, but it's better than losing data after a write.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The perag structure already has a pointer to the xfs_mount, so we don't
need to pass that separately and can drop it. Having done that, move
iter_flags so that the argument order is the same between xfs_inode_walk
and xfs_inode_walk_ag. The latter will make things less confusing for a
future patch that enables background scanning work to be done in
parallel.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
We're not very consistent about function names for the incore inode
iteration function. Turn them all into xfs_inode_walk* variants.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Move the xfs_inode_ag_iterator function to be nearer xfs_inode_ag_walk
so that we don't have to scroll back and forth to figure out how the
incore inode walking function works. No functional changes.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Brian Foster <bfoster@redhat.com>
