This patch enables USB OTG HS on stm32mp157c-ev1 in Peripheral mode.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support for USB OTG HS on STM32MP157C SoC.
USB OTG HS controller is based on DWC2 controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB Host (USBH) EHCI controller on stm32mp157c-ev1.
As a hub is used between USBH and USB connectors, no need to enable
USBH OHCI controller: all low- and full-speed traffic is managed by the
hub.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The AM3517 has a different OTG controller location than the OMAP3,
which is included from omap3.dtsi. This results in a hwmod error.
Since the AM3517 has a different OTG controller address, this patch
disabes one that is isn't available.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Libretech ALL-H3-CC has a high density connector for attaching
an eMMC module. The module form factor and connection is specific
to Libretech, and has provisions for split vmmc/vqmmc (core and I/O)
voltage supplies, but this board does not wire the vqmmc side. The
H2+/H3/H5 SoCs do not support alternate I/O voltages for eMMC either.
Only 3.3V is supported. A specific module that ties vqmmc to vmmc,
with both at 3.3V, must be used.
Given that a) eMMC is not designed to be hotplugged, b) power is
always provided on the pins, and c) MMC controllers can deal with
missing cards, we can enable this by default. If a module is attached
it will be picked up by the system.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Banana Pi M2 Zero board has a SY8113B regulator, which is controlled via
GPIO and capable of outputing 1.1V when the PL1 GPIO is set to output 0
or 1.1V when the PL6 GPIO is set to input or output 1, and the output is
the power supply of the ARM cores in H3 SoC.
Add the device tree node of this regulator and set the cpu's cpu-supply
property to it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add a label for the PMU node so that the board dts may be able to
pass the 'secure-reg-access' property like this:
&pmu {
secure-reg-access;
};
This also makes it consistent with the PMU node in imx6qdl.dtsi
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per the i.MX53 Reference Manual add an entry for the
'tigerp' region in the device tree.
This is needed for accessing the ARM_GPC register to set the
DBGEN bit, so that the debug clocks can be turned on.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As per the i.MX51 Reference Manual add an entry for the
'tigerp' region in the device tree.
This is needed for accessing the ARM_GPC register to set the
DBGEN bit, so that the debug clocks can be turned on.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6UL has GPIO clock gates in CCM CCGR, add
clock property for GPIO driver to make sure all
GPIO banks work as expected.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With old bindings imx_gpc_onecell_data always sets num_domains to 2 so
the DISPMIX domain can't actually be referenced. The pd is still defined
and pm core shuts it down as "unused" so display can't work.
Fix this by converting to new gpc bindings by adding pgc nodes and
referencing the newly-defined &pu_disp domain from &lcdif.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
100/200MHz states for USDHC3 are not required since the SoC
does not support modes faster than DDR52 for the on board eMMC.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
VDDD is connected to VGEN4 of the PF0100. This rail should only
run at 1.8V since there are multiple consumer and they all
expect the rail to be at 1.8V.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the 2.5V regulator, it does not exist. There is 3.3V and
3.3V_AUDIO provided to the module through the edge connector,
model those as fixed regulators like we use to do in other
Colibri device trees. The SGTL5000 uses 3.3V_AUDIO as VDDA. Note
that the driver derives the analog ground voltage (VAG) from this
supply. The new value should allow higher output swings before
clipping occurs. Refer to the SGTL5000 datasheet for details.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The fixed 1.8V regulator is not used, and there is in fact no
fixed 1.8V regulator on the module. Remove it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the disable-wp to indicate that Apalis and Colibri iMX6 do not
make use of the native write-protect signal available on the i.MX 6
SoCs. This prevents warnings:
mmc0: host does not support reading read-only switch, assuming write-enable
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use no-1-8-v device tree property to indicate that the board does
not support 1.8V signaling. The property voltage-ranges seems not
appropriate in our case since we do not have level shifters in
place.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the 3.3V main supply on the carrier board. Currently as a fixed
supply since not all consumer are modeled yet. This gets also rid of
some missing supply warnings.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit 654f2b937b ("crypto: caam - allow retrieving 'era' from
register") the CAAM driver is capable of obtaining the era version by
reading the appropriate CAAM registers, so let the CAAM driver discover
the era version in run-time instead of hardcoding such information in the
device tree.
According to Documentation/devicetree/bindings/crypto/fsl-sec4.txt the
'fsl,sec-era' is an optional property and this can be safely removed
now.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The change adds a number of basic peripherals found on i.MX31 SoC:
* GPIO controllers,
* I2C master controllers,
* SPI master controllers,
* ATA controller,
* SDHC controllers,
* RTC, watchdog and PWM contollers,
* SDMA,
* IRAM,
* NAND and WEIM controllers on EMI.
The added controller devices were tested on Freescale i.MX31 powered
LogicPD Lite SoM and baseboard.
DMA functionality was tested on SDHC and SPI controllers so far,
thus dmas properties are added to those device nodes only.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a SRAM controller node for the H3, with support for the C1
SRAM region that is shared between the Video Engine and the CPU.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the compatible and commit prefix]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds a SRAM controller node for the A23 and A33, with support for
the C1 SRAM region that is shared between the Video Engine and the CPU.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the prefix and the compatibles]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for the A20 platform. The region is shared
between the Video Engine and the CPU.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the SRAM C size]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This adds support for the C1 SRAM region (to be used with the SRAM
controller driver) for sun5i-based platforms. The region is shared
between the Video Engine and the CPU.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Fixed the SRAM C size to take the C2 and C3 SRAM into account]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches the sun7i-a20 dtsi to use the most qualified compatibles
for the system-control block (previously named SRAM controller) as well
as the SRAM blocks. The sun4i-a10 compatibles are kept since these
hardware blocks are backward-compatible.
The node name for system control is also updated to reflect the fact that
the controller described is really about system control rather than SRAM
control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches the sun5i dtsi to use the most qualified compatibles for
the system-control block (previously named SRAM controller) as well as
the SRAM blocks.
The node name for system control is also updated to reflect the fact that
the controller described is really about system control rather than SRAM
control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Removed the A10 compatible for the driver]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This switches the sun4i-a10 dtsi to use the new compatible for the
system-control block (previously named SRAM controller) instead of
the deprecated one.
The node name is also updated to reflect the fact that the controller
described is really about system control rather than SRAM control.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
[Maxime: Amended the commit message]
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
R40 has 4 TCONs, but only 2 of them can receive some kind of output at
the same time. Let's disable them by default, so only those which are
really connected on board can be enabled in board dts file.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Current R40 is missing some graph connections between TCON TOP and
TCONs.
Add them.
Fixes: 05a43a262d ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A83T and R40 TCON TV are very similar. However, R40 TCON TV is wired
differently, which makes it incompatible with A83T TCON TV.
Because of that, remove fallback A83T TCON TV compatible.
Fixes: 05a43a262d ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
sun4i-drm DT binding, second paragraph of the first section says:
For all connections between components up to the TCONs in the display
pipeline, when there are multiple components of the same type at the
same depth, the local endpoint ID must be the same as the remote
component's index.
Add mixer ids in R40 DT as mandated by DT binding.
Fixes: 05a43a262d ("ARM: dts: sun8i: r40: Add HDMI pipeline")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add support for the MCAN peripheral which supports both classic
CAN messages along with the new CAN-FD message.
Add MCAN node to evm and enable it with a maximum datarate of 5 mbps
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ti-sysc driver provides support for manipulating the idle modes
and interconnect level resets.
Add the generic interconnect target module node for MCAN to support
the same.
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MCAN is clocked by H14 divider of DPLL_GMAC. Unlike other
DPLL dividers this DPLL_GMAC H14 divider is controlled by
control module. Adding support for these clocks.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the power-domains property to CPPI 4.1 node.
The CPPI 4.1 DMA driver uses pm_runtime to manage the clocks,
so it needs this property in order to find and enable the clock
properly.
Reviewed-by: David Lechner <david@lechnology.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This enables the on-module ONFI conformant NAND flash.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add basic controller device tree node to be extended by
individual boards. Use the assigned-clocks mechanism to set
NDFLASH clock to a sensible default rate of 150MHz.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Colibri-T20 can come in 256 MB RAM (with 512 MB NAND) or 512 MB RAM
(with 1024 MB NAND) flavors. Both of them will use the same DTSI
expecting the bootloader to do the fixup of /memory node. However in
case it does not happen, let's stay on safe side by limiting the memory
to 256 MB for both versions of Colibri-T20.
Rename to remove the unnecessary memory size from the device tree file
name. While at it, also follow the typical Toradex SoC, module, carrier
board hierarchy.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove unneeded address/size cells properties and unit addresses to fix
DTC warnings like:
arch/arm/boot/dts/tegra30-apalis-eval.dtb: Warning (unit_address_vs_reg):
/i2c@7000d000/stmpe811@41/stmpe_touchscreen@0: node has a unit name, but no reg property
arch/arm/boot/dts/tegra30-apalis-eval.dtb: Warning (avoid_unnecessary_addr_size):
/i2c@7000d000/stmpe811@41: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a generic /memory node in each Tegra DTSI (with empty reg property,
to be overidden by each DTS) and set proper unit address for /memory
nodes to fix the DTC warnings:
arch/arm/boot/dts/tegra20-harmony.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
The DTB after the change is the same as before except adding
unit-address to /memory node.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the usage of skeleton.dtsi because it was deprecated since commit
9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi as deprecated").
It also allows later to fix DTC warnings for missing unit name in
/memory nodes.
Compiled DTBs are the same as before this commit.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
