The THC63LVDM83D is a transparent LVDS encoder. Unlike dumb LVDS
encoders it can be controlled through a few pins (power down, LVDS
swing, clock edge selection) and requires power supplies. However, on
several boards where the device is used neither the control pins nor the
power supply are controllable.
To avoid developing a separate device-specific driver add a
"thine,thc63lvdm83d" compatible entry to the lvds-encoder driver. This
will allow supporting many THC63LVDM83D-based boards easily, while
allowing future development of an thc63lvdm83d driver when needed
without breaking backward compatibility.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-5-laurent.pinchart+renesas@ideasonboard.com
The ADV7123 is a transparent VGA DAC. Unlike dumb VGA DACs it can be
controlled through a power save pin, and requires a power supply.
However, on most boards where the device is used neither the power save
signal nor the power supply are controllable.
To avoid developing a separate device-specific driver add an
"adi,adv7123" compatible entry to the dumb-vga-dac driver. This will
allow supporting most ADV7123-based boards easily, while allowing future
development of an adv7123 driver when needed without breaking backward
compatibility.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302104728.7150-4-laurent.pinchart+renesas@ideasonboard.com
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
On VLV/CHV enabling sprite0 when sprite1 has already been enabled may
lead to an underrun. This only happens when sprite0 FIFO size is zero
prior to enabling it. Hence an effective workaround is to always
allocate at least one cacheline for sprite0 when sprite1 is active.
I've not observed this sort of failure during any other type of plane
enable/disable sequence.
v2: s/noninverted/raw/ for consistency with other platforms
Testcase: igt/kms_plane_blinker
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-14-ville.syrjala@linux.intel.com
Remove crtc->wm.cxsr_allowed and just rely on crtc_state->disable_cxsr
instead. This was used only by vlv/chv to indicate whether to enable
cxsr in the wm computation. That doesn't really work anymore, and as far
as the optimal watermarks go we'll just consider the number of planes
and the current pipe, and for the intermediate watermarks we'll also
start to consider disable_cxsr which is set appropriately when planes
are being enabled/disabled.
We'll also flip over the crtc_state->wm.need_postvbl_update setup so
that it's the wm code that will set it. Previously the generic code set
it up, and then the wm code cleared it again if it thought it's not
needed after all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-11-ville.syrjala@linux.intel.com
Since the watermark registers arent double buffered on VLV/CHV, we'll
need to play around with intermediate watermarks same was as we do on
ILK-BDW.
The watermark registers on VLV/CHV contain inverted values, so to find
the intermediate watermark value we just take the minimum of the
active and optimal values. This also means that, unlike ILK-BDW,
there's no chance that we'd fail to find a working intermediate
watermarks. As long as both the active and optimal watermarks are valid
the intermediate watermarks will come out valid as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-10-ville.syrjala@linux.intel.com
Check whether anything relevant has actually change when we compute new
watermarks for each plane in the state. If the watermarks for no
primary/sprite planes changed we don't have to recompute the FIFO split
or reprogram the DSBARB registers. And even the cursor watermarks didn't
change we can skip the merge+invert step between all the planes on
the pipe as well.
v2: s/noninverted/raw/ for consistency with other platforms
v3: Drop duplicated vlv_get_fifo_size() call during init
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-9-ville.syrjala@linux.intel.com
Start computing the vlv/chv watermarks the atomic way, from the
.compute_pipe_wm() hook. We'll recompute the actual watermarks
for only planes that are part of the state, the other planes will
keep their watermark from the last time it was computed.
And the actual watermark programming will happen from the
.initial_watermarks() hook. For now we'll just compute the
optimal watermarks, and we'll hook up the intermediate
watermarks properly later.
The DSPARB registers responsible for the FIFO paritioning are
double buffered, so they will be programming from
intel_begin_crtc_commit().
v2: s/noninverted/raw/ for consistency with other platforms
s/vlv_plane_wm_set/vlv_raw_plane_wm_set/ for clarity
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-8-ville.syrjala@linux.intel.com
Let's compute the watermarks first and the FIFO size second. This way we
can make sure the FIFO split is the most accommodating to the watermarks.
Previously we could have potentially computed a FIFO split that couldn't
accommodate the PM2 watermarks simply due to a bad split even if the
total FIFO size would have been sufficient.
It'll also allow us to avoid recomputing the wms for all planes whenever
the FIFO split would change. Thus we don't have to add any extra planes
to the state when the FIFO needs to be repartitioned.
To help with this we'll keep around copies of the non-inverted
watermarks in the crtc state. For now that doesn't help too much, but
once we start to do the watermark computation only for the planes
that change we'll need the non-inverted values around for the other
planes.
v2: s/noninverted/raw/ for consistency with other platforms
Fix the memset() of the "raw" watermarks
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302171508.1666-7-ville.syrjala@linux.intel.com
If we setup the vm size early, we can use the newly introduced
i915_vm_is_48bit() in majority of callsites wanting to know the vm size.
As we operate either with 3lvl or 4lvl page table structure,
wrap the vm size query inside a function which tells us if
4lvl setup is needed for particular vm, as the following
code uses the function names where level is noted.
v2: use_4lvl (Chris)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1488295691-9404-3-git-send-email-mika.kuoppala@intel.com
During reset_all_global_seqno() on seqno rollover, we have to update the
HWS. This causes all in flight requests to be completed, so first we
wait. However, we were only waiting for the requests themselves to be
completed and clearing out the waiter rbtrees - what I had missed was
the extra reference in execlists->port[]. Since commit fe9ae7a3bf
("drm/i915/execlists: Detect an out-of-order context switch") we can
detect when the request is retired before the context switch interrupt
is completed. The impact should be neglible outside of debugging.
Testcase: igt/gem_exec_whisper
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170303121947.20482-1-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Pull vfs pile two from Al Viro:
- orangefs fix
- series of fs/namei.c cleanups from me
- VFS stuff coming from overlayfs tree
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
orangefs: Use RCU for destroy_inode
vfs: use helper for calling f_op->fsync()
mm: use helper for calling f_op->mmap()
vfs: use helpers for calling f_op->{read,write}_iter()
vfs: pass type instead of fn to do_{loop,iter}_readv_writev()
vfs: extract common parts of {compat_,}do_readv_writev()
vfs: wrap write f_ops with file_{start,end}_write()
vfs: deny copy_file_range() for non regular files
vfs: deny fallocate() on directory
vfs: create vfs helper vfs_tmpfile()
namei.c: split unlazy_walk()
namei.c: fold the check for DCACHE_OP_REVALIDATE into d_revalidate()
lookup_fast(): clean up the logics around the fallback to non-rcu mode
namei: fold unlazy_link() into its sole caller
Adding to the tail of the client request list as the only other user is
in the throttle ioctl that iterates forwards over the list. It only
needs protection against deletion of a request as it reads it, it simply
won't see a new request added to the end of the list, or it would be too
early and rejected. We can further reduce the number of spinlocks
required when throttling by removing stale requests from the client_list
as we throttle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170302122525.19675-1-chris@chris-wilson.co.uk
Pull vhost updates from Michael Tsirkin:
"virtio, vhost: optimizations, fixes
Looks like a quiet cycle for vhost/virtio, just a couple of minor
tweaks. Most notable is automatic interrupt affinity for blk and scsi.
Hopefully other devices are not far behind"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-console: avoid DMA from stack
vhost: introduce O(1) vq metadata cache
virtio_scsi: use virtio IRQ affinity
virtio_blk: use virtio IRQ affinity
blk-mq: provide a default queue mapping for virtio device
virtio: provide a method to get the IRQ affinity mask for a virtqueue
virtio: allow drivers to request IRQ affinity when creating VQs
virtio_pci: simplify MSI-X setup
virtio_pci: don't duplicate the msix_enable flag in struct pci_dev
virtio_pci: use shared interrupts for virtqueues
virtio_pci: remove struct virtio_pci_vq_info
vhost: try avoiding avail index access when getting descriptor
virtio_mmio: expose header to userspace
Currently ILK-BDW explicitly disable LP1+ watermarks from their
.init_clock_gating() hooks. Unfortunately that hook gets called way too
late since by that time we've already initialized all the watermark
state tracking which then gets out of sync with the hardware state.
We may eventually want to consider killing off the explicit LP1+
disable from .init_clock_gating(). In the meantime however, we can
avoid the problem by reordering the init sequence such that
intel_modeset_init_hw()->intel_init_clock_gating() gets called
prior to the hardware state takeover.
I suppose prior to the two stage watermark programming we were
magically saved by something that forced the watermarks to be
reprogrammed fully after .init_clock_gating() got called. But
now that no longer happens.
Note that the diff might look a bit odd as it kills off one
call of intel_update_cdclk(), but that's fine because
intel_modeset_init_hw() does the exact same thing. Previously
we just did it twice.
Actually even this new init sequence is pretty bogus as
.init_clock_gating() really should be called before any gem
hardware init since it can configure various clock gating
workarounds and whatnot that affect the GT side as well. Also
intel_modeset_init() really should get split up into better
defined init stages. Another "fun" detail is that
intel_modeset_gem_init() is where RPS/RC6 gets configured.
Why that is done from the display code is beyond me. I've
decided to leave all this be for now, and just try to fix
the init sequence enough for watermarks to work.
Cc: stable@vger.kernel.org
Cc: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Cc: David Purton <dcpurton@marshwiggle.net>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reported-by: David Purton <dcpurton@marshwiggle.net>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96645
Fixes: ed4a6a7ca8 ("drm/i915: Add two-stage ILK-style watermark programming (v11)")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170220140443.30891-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The from_cache flag was actually "the BO is invisible to userspace",
so we can repurpose it to just zero out a cached BO and return it to
userspace.
Improves wall time for a loop of 5 glsl-algebraic-add-add-1 by
-1.44989% +/- 0.862891% (n=28, 1 outlier removed from each that
appeared to be other system noise)
Note that there's an intel-gpu-tools test to check for the proper
zeroing behavior here, which we continue to pass.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170301185602.6873-1-eric@anholt.net
