Changes in 5.10.85
usb: gadget: uvc: fix multiple opens
gcc-plugins: simplify GCC plugin-dev capability test
gcc-plugins: fix gcc 11 indigestion with plugins...
HID: quirks: Add quirk for the Microsoft Surface 3 type-cover
HID: google: add eel USB id
HID: add hid_is_usb() function to make it simpler for USB detection
HID: add USB_HID dependancy to hid-prodikeys
HID: add USB_HID dependancy to hid-chicony
HID: add USB_HID dependancy on some USB HID drivers
HID: bigbenff: prevent null pointer dereference
HID: wacom: fix problems when device is not a valid USB device
HID: check for valid USB device for many HID drivers
nft_set_pipapo: Fix bucket load in AVX2 lookup routine for six 8-bit groups
IB/hfi1: Insure use of smp_processor_id() is preempt disabled
IB/hfi1: Fix early init panic
IB/hfi1: Fix leak of rcvhdrtail_dummy_kvaddr
can: kvaser_usb: get CAN clock frequency from device
can: kvaser_pciefd: kvaser_pciefd_rx_error_frame(): increase correct stats->{rx,tx}_errors counter
can: sja1000: fix use after free in ems_pcmcia_add_card()
x86/sme: Explicitly map new EFI memmap table as encrypted
drm/amd/amdkfd: adjust dummy functions' placement
drm/amdkfd: separate kfd_iommu_resume from kfd_resume
drm/amdgpu: add amdgpu_amdkfd_resume_iommu
drm/amdgpu: move iommu_resume before ip init/resume
drm/amdgpu: init iommu after amdkfd device init
drm/amdkfd: fix boot failure when iommu is disabled in Picasso.
nfc: fix potential NULL pointer deref in nfc_genl_dump_ses_done
selftests: netfilter: add a vrf+conntrack testcase
vrf: don't run conntrack on vrf with !dflt qdisc
bpf, x86: Fix "no previous prototype" warning
bpf: Fix the off-by-two error in range markings
ice: ignore dropped packets during init
bonding: make tx_rebalance_counter an atomic
nfp: Fix memory leak in nfp_cpp_area_cache_add()
seg6: fix the iif in the IPv6 socket control block
udp: using datalen to cap max gso segments
netfilter: conntrack: annotate data-races around ct->timeout
iavf: restore MSI state on reset
iavf: Fix reporting when setting descriptor count
IB/hfi1: Correct guard on eager buffer deallocation
devlink: fix netns refcount leak in devlink_nl_cmd_reload()
net/sched: fq_pie: prevent dismantle issue
KVM: x86: Wait for IPIs to be delivered when handling Hyper-V TLB flush hypercall
mm: bdi: initialize bdi_min_ratio when bdi is unregistered
ALSA: ctl: Fix copy of updated id with element read/write
ALSA: hda/realtek - Add headset Mic support for Lenovo ALC897 platform
ALSA: hda/realtek: Fix quirk for TongFang PHxTxX1
ALSA: pcm: oss: Fix negative period/buffer sizes
ALSA: pcm: oss: Limit the period size to 16MB
ALSA: pcm: oss: Handle missing errors in snd_pcm_oss_change_params*()
scsi: qla2xxx: Format log strings only if needed
btrfs: clear extent buffer uptodate when we fail to write it
btrfs: replace the BUG_ON in btrfs_del_root_ref with proper error handling
md: fix update super 1.0 on rdev size change
nfsd: fix use-after-free due to delegation race
nfsd: Fix nsfd startup race (again)
tracefs: Have new files inherit the ownership of their parent
mmc: renesas_sdhi: initialize variable properly when tuning
clk: qcom: regmap-mux: fix parent clock lookup
drm/syncobj: Deal with signalled fences in drm_syncobj_find_fence.
can: pch_can: pch_can_rx_normal: fix use after free
can: m_can: Disable and ignore ELO interrupt
libata: add horkage for ASMedia 1092
wait: add wake_up_pollfree()
binder: use wake_up_pollfree()
signalfd: use wake_up_pollfree()
aio: keep poll requests on waitqueue until completed
aio: fix use-after-free due to missing POLLFREE handling
net: mvpp2: fix XDP rx queues registering
tracefs: Set all files to the same group ownership as the mount option
block: fix ioprio_get(IOPRIO_WHO_PGRP) vs setuid(2)
scsi: pm80xx: Do not call scsi_remove_host() in pm8001_alloc()
scsi: scsi_debug: Fix buffer size of REPORT ZONES command
qede: validate non LSO skb length
PM: runtime: Fix pm_runtime_active() kerneldoc comment
ASoC: rt5682: Fix crash due to out of scope stack vars
ASoC: qdsp6: q6routing: Fix return value from msm_routing_put_audio_mixer
ASoC: codecs: wsa881x: fix return values from kcontrol put
ASoC: codecs: wcd934x: handle channel mappping list correctly
ASoC: codecs: wcd934x: return correct value from mixer put
RDMA/hns: Do not halt commands during reset until later
RDMA/hns: Do not destroy QP resources in the hw resetting phase
clk: imx: use module_platform_driver
i40e: Fix failed opcode appearing if handling messages from VF
i40e: Fix pre-set max number of queues for VF
mtd: rawnand: fsmc: Take instruction delay into account
mtd: rawnand: fsmc: Fix timing computation
i40e: Fix NULL pointer dereference in i40e_dbg_dump_desc
Revert "PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge"
perf tools: Fix SMT detection fast read path
Documentation/locking/locktypes: Update migrate_disable() bits.
dt-bindings: net: Reintroduce PHY no lane swap binding
tools build: Remove needless libpython-version feature check that breaks test-all fast path
net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero
net: altera: set a couple error code in probe()
net: fec: only clear interrupt of handling queue in fec_enet_rx_queue()
net, neigh: clear whole pneigh_entry at alloc time
net/qla3xxx: fix an error code in ql_adapter_up()
selftests/fib_tests: Rework fib_rp_filter_test()
USB: gadget: detect too-big endpoint 0 requests
USB: gadget: zero allocate endpoint 0 buffers
usb: core: config: fix validation of wMaxPacketValue entries
xhci: Remove CONFIG_USB_DEFAULT_PERSIST to prevent xHCI from runtime suspending
usb: core: config: using bit mask instead of individual bits
xhci: avoid race between disable slot command and host runtime suspend
iio: gyro: adxrs290: fix data signedness
iio: trigger: Fix reference counting
iio: trigger: stm32-timer: fix MODULE_ALIAS
iio: stk3310: Don't return error code in interrupt handler
iio: mma8452: Fix trigger reference couting
iio: ltr501: Don't return error code in trigger handler
iio: kxsd9: Don't return error code in trigger handler
iio: itg3200: Call iio_trigger_notify_done() on error
iio: dln2-adc: Fix lockdep complaint
iio: dln2: Check return value of devm_iio_trigger_register()
iio: at91-sama5d2: Fix incorrect sign extension
iio: adc: stm32: fix a current leak by resetting pcsel before disabling vdda
iio: adc: axp20x_adc: fix charging current reporting on AXP22x
iio: ad7768-1: Call iio_trigger_notify_done() on error
iio: accel: kxcjk-1013: Fix possible memory leak in probe and remove
csky: fix typo of fpu config macro
irqchip/aspeed-scu: Replace update_bits with write_bits.
irqchip/armada-370-xp: Fix return value of armada_370_xp_msi_alloc()
irqchip/armada-370-xp: Fix support for Multi-MSI interrupts
irqchip/irq-gic-v3-its.c: Force synchronisation when issuing INVALL
irqchip: nvic: Fix offset for Interrupt Priority Offsets
misc: fastrpc: fix improper packet size calculation
bpf: Add selftests to cover packet access corner cases
kbuild: simplify GCC_PLUGINS enablement in dummy-tools/gcc
doc: gcc-plugins: update gcc-plugins.rst
MAINTAINERS: adjust GCC PLUGINS after gcc-plugin.sh removal
Documentation/Kbuild: Remove references to gcc-plugin.sh
Linux 5.10.85
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
Change-Id: I351da1b00f30a370b021125180a48b1c1ecb97ce
commit 9b6164342e981d751e69f5a165dd596ffcdfd6fe upstream.
This document was written a long time ago. Update it.
[1] Drop the version information
The range of the supported GCC versions are always changing. The
current minimal GCC version is 4.9, and commit 1e860048c53e
("gcc-plugins: simplify GCC plugin-dev capability test") removed the
old code accordingly.
We do not need to mention specific version ranges like "all gcc versions
from 4.5 to 6.0" since we forget to update the documentation when we
raise the minimal compiler version.
[2] Drop the C compiler statements
Since commit 77342a02ff ("gcc-plugins: drop support for GCC <= 4.7")
the GCC plugin infrastructure only supports g++.
[3] Drop supported architectures
As of v5.11-rc4, the infrastructure supports more architectures;
arm, arm64, mips, powerpc, riscv, s390, um, and x86. (just grep
"select HAVE_GCC_PLUGINS") Again, we miss to update this document when a
new architecture is supported. Let's just say "only some architectures".
[4] Update the apt-get example
We are now discussing to bump the minimal version to GCC 5. The GCC 4.9
support will be removed sooner or later. Change the package example to
gcc-10-plugin-dev while we are here.
[5] Update the build target
Since commit ce2fd53a10 ("kbuild: descend into scripts/gcc-plugins/
via scripts/Makefile"), "make gcc-plugins" is not supported.
"make scripts" builds all the enabled plugins, including some other
tools.
[6] Update the steps for adding a new plugin
At first, all CONFIG options for GCC plugins were located in arch/Kconfig.
After commit 45332b1bdf ("gcc-plugins: split out Kconfig entries to
scripts/gcc-plugins/Kconfig"), scripts/gcc-plugins/Kconfig became the
central place to collect plugin CONFIG options. In my understanding,
this requirement no longer exists because commit 9f671e5815 ("security:
Create "kernel hardening" config area") moved some of plugin CONFIG
options to another file. Find an appropriate place to add the new CONFIG.
The sub-directory support was never used by anyone, and removed by
commit c17d6179ad ("gcc-plugins: remove unused GCC_PLUGIN_SUBDIR").
Remove the useless $(src)/ prefix.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f4c3b83b75b91c5059726cb91e3165cc01764ce7 upstream.
With commit 1e860048c53e ("gcc-plugins: simplify GCC plugin-dev
capability test") applied, this hunk can be way simplified because
now scripts/gcc-plugins/Kconfig only checks plugin-version.h
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b560b21f71eb4ef9dfc7c8ec1d0e4d7f9aa54b51 upstream.
This commit adds BPF verifier selftests that cover all corner cases by
packet boundary checks. Specifically, 8-byte packet reads are tested at
the beginning of data and at the beginning of data_meta, using all kinds
of boundary checks (all comparison operators: <, >, <=, >=; both
permutations of operands: data + length compared to end, end compared to
data + length). For each case there are three tests:
1. Length is just enough for an 8-byte read. Length is either 7 or 8,
depending on the comparison.
2. Length is increased by 1 - should still pass the verifier. These
cases are useful, because they failed before commit 2fa7d94afc1a
("bpf: Fix the off-by-two error in range markings").
3. Length is decreased by 1 - should be rejected by the verifier.
Some existing tests are just renamed to avoid duplication.
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211207081521.41923-1-maximmi@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b383a42ca523ce54bcbd63f7c8f3cf974abc9b9a upstream.
INVALL CMD specifies that the ITS must ensure any caching associated with
the interrupt collection defined by ICID is consistent with the LPI
configuration tables held in memory for all Redistributors. SYNC is
required to ensure that INVALL is executed.
Currently, LPI configuration data may be inconsistent with that in the
memory within a short period of time after the INVALL command is executed.
Signed-off-by: Wudi Wang <wangwudi@hisilicon.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: cc2d3216f5 ("irqchip: GICv3: ITS command queue")
Link: https://lore.kernel.org/r/20211208015429.5007-1-zhangshaokun@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0a553502efd545c1ce3fd08fc4d423f8e4ac3d6 upstream.
irq-armada-370-xp driver already sets MSI_FLAG_MULTI_PCI_MSI flag into
msi_domain_info structure. But allocated interrupt numbers for Multi-MSI
needs to be properly aligned otherwise devices send MSI interrupt with
wrong number.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area() to allocate aligned interrupt numbers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: a71b9412c9 ("irqchip/armada-370-xp: Allow allocation of multiple MSIs")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211125130057.26705-2-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6661146427cbbce6d1fe3dbb11ff1c487f55799a upstream.
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The ad7768-1 driver neglects to call iio_trigger_notify_done() when there
is an error reading the converter data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
Fixes: a5f8c7da3d ("iio: adc: Add AD7768-1 ADC basic support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211101144055.13858-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92beafb76a31bdc02649eb44e93a8e4f4cfcdbe8 upstream.
Both the charging and discharging currents on AXP22x are stored as
12-bit integers, in accordance with the datasheet.
It's also confirmed by vendor BSP (axp20x_adc.c:axp22_icharge_to_mA).
The scale factor of 0.5 is never mentioned in datasheet, nor in the
vendor source code. I think it was here to compensate for
erroneous addition bit in register width.
Tested on custom A40i+AXP221s board with external ammeter as
a reference.
Fixes: 0e34d5de96 ("iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs")
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20211116213746.264378-1-boger@wirenboard.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f711f28e71e965c0d1141c830fa7131b41abbe75 upstream.
Some I/Os are connected to ADC input channels, when the corresponding bit
in PCSEL register are set on STM32H7 and STM32MP15. This is done in the
prepare routine of stm32-adc driver.
There are constraints here, as PCSEL shouldn't be set when VDDA supply
is disabled. Enabling/disabling of VDDA supply in done via stm32-adc-core
runtime PM routines (before/after ADC is enabled/disabled).
Currently, PCSEL remains set when disabling ADC. Later on, PM runtime
can disable the VDDA supply. This creates some conditions on I/Os that
can start to leak current.
So PCSEL needs to be cleared when disabling the ADC.
Fixes: 95e339b6e8 ("iio: adc: stm32: add support for STM32H7")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/1634905169-23762-1-git-send-email-fabrice.gasnier@foss.st.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67fe29583e72b2103abb661bb58036e3c1f00277 upstream.
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The itg3200 driver neglects to call iio_trigger_notify_done() when there is
an error reading the gyro data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
Fixes: 9dbf091da0 ("iio: gyro: Add itg3200")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211101144055.13858-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45febe0d63917ee908198c5be08511c64ee1790a upstream.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The kxsd9 interrupt handler returns an error code if reading the data
registers fails. In addition when exiting due to an error the trigger
handler does not call `iio_trigger_notify_done()`. Which when not done
keeps the triggered disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
Since we can't return the error code make sure to at least log it as part
of the error message.
Fixes: 0427a106a9 ("iio: accel: kxsd9: Add triggered buffer handling")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211024171251.22896-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef9d67fa72c1b149a420587e435a3e888bdbf74f upstream.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The ltr501 interrupt handler gets this right for most error paths, but
there is one case where it returns the error code.
In addition for this particular case the trigger handler does not call
`iio_trigger_notify_done()`. Which when not done keeps the triggered
disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
Fixes: 2690be9051 ("iio: Add Lite-On ltr501 ambient light / proximity sensor driver")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024171251.22896-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd0082235783f814241a1c9483fb89e405f4f892 upstream.
The mma8452 driver directly assigns a trigger to the struct iio_dev. The
IIO core when done using this trigger will call `iio_trigger_put()` to drop
the reference count by 1.
Without the matching `iio_trigger_get()` in the driver the reference count
can reach 0 too early, the trigger gets freed while still in use and a
use-after-free occurs.
Fix this by getting a reference to the trigger before assigning it to the
IIO device.
Fixes: ae6d9ce056 ("iio: mma8452: Add support for interrupt driven triggers.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024092700.6844-1-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e1eeca5afa7ba84d885987165dbdc5decf15413 upstream.
Interrupt handlers must return one of the irqreturn_t values. Returning a
error code is not supported.
The stk3310 event interrupt handler returns an error code when reading the
flags register fails.
Fix the implementation to always return an irqreturn_t value.
Fixes: 3dd477acbd ("iio: light: Add threshold interrupt support for STK3310")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211024171251.22896-3-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a827a4984664308f13599a0b26c77018176d0c7c upstream.
In viio_trigger_alloc() device_initialize() is used to set the initial
reference count of the trigger to 1. Then another get_device() is called on
trigger. This sets the reference count to 2 before the trigger is returned.
iio_trigger_free(), which is the matching API to viio_trigger_alloc(),
calls put_device() which decreases the reference count by 1. But the second
reference count acquired in viio_trigger_alloc() is never dropped.
As a result the iio_trigger_release() function is never called and the
memory associated with the trigger is never freed.
Since there is no reason for the trigger to start its lifetime with two
reference counts just remove the extra get_device() in
viio_trigger_alloc().
Fixes: 5f9c035cae ("staging:iio:triggers. Add a reference get to the core for triggers.")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20211024092700.6844-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7faac1953ed1f658f719cdf7bb7303fa5eef822c upstream.
Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.
Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.
This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.
usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 811ae81320da53a5670c36970cefacca8519f90e upstream.
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3910c80966e4a76b25ce812f6bea0ef1b1d530 upstream.
The checks performed by commit aed9d65ac3 ("USB: validate
wMaxPacketValue entries in endpoint descriptors") require that initial
value of the maxp variable contains both maximum packet size bits
(10..0) and multiple-transactions bits (12..11). However, the existing
code assings only the maximum packet size bits. This patch assigns all
bits of wMaxPacketSize to the variable.
Fixes: aed9d65ac3 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20211210085219.16796-1-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86ebbc11bb3f60908a51f3e41a17e3f477c2eaa3 upstream.
Under some conditions, USB gadget devices can show allocated buffer
contents to a host. Fix this up by zero-allocating them so that any
extra data will all just be zeros.
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Tested-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 153a2d7e3350cc89d406ba2d35be8793a64c2038 upstream.
Sometimes USB hosts can ask for buffers that are too large from endpoint
0, which should not be allowed. If this happens for OUT requests, stall
the endpoint, but for IN requests, trim the request size to the endpoint
buffer size.
Co-developed-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f6071e5e3961eeb5300bd0901c9e128598730ae3 upstream.
Currently rp_filter tests in fib_tests.sh:fib_rp_filter_test() are
failing. ping sockets are bound to dummy1 using the "-I" option
(SO_BINDTODEVICE), but socket lookup is failing when receiving ping
replies, since the routing table thinks they belong to dummy0.
For example, suppose ping is using a SOCK_RAW socket for ICMP messages.
When receiving ping replies, in __raw_v4_lookup(), sk->sk_bound_dev_if
is 3 (dummy1), but dif (skb_rtable(skb)->rt_iif) says 2 (dummy0), so the
raw_sk_bound_dev_eq() check fails. Similar things happen in
ping_lookup() for SOCK_DGRAM sockets.
These tests used to pass due to a bug [1] in iputils, where "ping -I"
actually did not bind ICMP message sockets to device. The bug has been
fixed by iputils commit f455fee41c07 ("ping: also bind the ICMP socket
to the specific device") in 2016, which is why our rp_filter tests
started to fail. See [2] .
Fixing the tests while keeping everything in one netns turns out to be
nontrivial. Rework the tests and build the following topology:
┌─────────────────────────────┐ ┌─────────────────────────────┐
│ network namespace 1 (ns1) │ │ network namespace 2 (ns2) │
│ │ │ │
│ ┌────┐ ┌─────┐ │ │ ┌─────┐ ┌────┐ │
│ │ lo │<───>│veth1│<────────┼────┼─>│veth2│<──────────>│ lo │ │
│ └────┘ ├─────┴──────┐ │ │ ├─────┴──────┐ └────┘ │
│ │192.0.2.1/24│ │ │ │192.0.2.1/24│ │
│ └────────────┘ │ │ └────────────┘ │
└─────────────────────────────┘ └─────────────────────────────┘
Consider sending an ICMP_ECHO packet A in ns2. Both source and
destination IP addresses are 192.0.2.1, and we use strict mode rp_filter
in both ns1 and ns2:
1. A is routed to lo since its destination IP address is one of ns2's
local addresses (veth2);
2. A is redirected from lo's egress to veth2's egress using mirred;
3. A arrives at veth1's ingress in ns1;
4. A is redirected from veth1's ingress to lo's ingress, again, using
mirred;
5. In __fib_validate_source(), fib_info_nh_uses_dev() returns false,
since A was received on lo, but reverse path lookup says veth1;
6. However A is not dropped since we have relaxed this check for lo in
commit 66f8209547 ("fib: relax source validation check for loopback
packets");
Making sure A is not dropped here in this corner case is the whole point
of having this test.
7. As A reaches the ICMP layer, an ICMP_ECHOREPLY packet, B, is
generated;
8. Similarly, B is redirected from lo's egress to veth1's egress (in
ns1), then redirected once again from veth2's ingress to lo's
ingress (in ns2), using mirred.
Also test "ping 127.0.0.1" from ns2. It does not trigger the relaxed
check in __fib_validate_source(), but just to make sure the topology
works with loopback addresses.
Tested with ping from iputils 20210722-41-gf9fb573:
$ ./fib_tests.sh -t rp_filter
IPv4 rp_filter tests
TEST: rp_filter passes local packets [ OK ]
TEST: rp_filter passes loopback packets [ OK ]
[1] https://github.com/iputils/iputils/issues/55
[2] f455fee41c
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: adb701d6cf ("selftests: add a test case for rp_filter")
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211201004720.6357-1-yepeilin.cs@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d17b9737c2bc09b4ac6caf469826e5a7ce3ffab7 upstream.
The ql_wait_for_drvr_lock() fails and returns false, then this
function should return an error code instead of returning success.
The other problem is that the success path prints an error message
netdev_err(ndev, "Releasing driver lock\n"); Delete that and
re-order the code a little to make it more clear.
Fixes: 5a4faa8737 ("[PATCH] qla3xxx NIC driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211207082416.GA16110@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b5bd95d17102b6719e3531d627875b9690371383 upstream.
Background:
We have a customer is running a Profinet stack on the 8MM which receives and
responds PNIO packets every 4ms and PNIO-CM packets every 40ms. However, from
time to time the received PNIO-CM package is "stock" and is only handled when
receiving a new PNIO-CM or DCERPC-Ping packet (tcpdump shows the PNIO-CM and
the DCERPC-Ping packet at the same time but the PNIO-CM HW timestamp is from
the expected 40 ms and not the 2s delay of the DCERPC-Ping).
After debugging, we noticed PNIO, PNIO-CM and DCERPC-Ping packets would
be handled by different RX queues.
The root cause should be driver ack all queues' interrupt when handle a
specific queue in fec_enet_rx_queue(). The blamed patch is introduced to
receive as much packets as possible once to avoid interrupt flooding.
But it's unreasonable to clear other queues'interrupt when handling one
queue, this patch tries to fix it.
Fixes: ed63f1dcd5 (net: fec: clear receive interrupts before processing a packet)
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Nicolas Diaz <nicolas.diaz@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20211206135457.15946-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit badd7857f5c933a3dc34942a2c11d67fdbdc24de upstream.
There are two error paths which accidentally return success instead of
a negative error code.
Fixes: bbd2190ce9 ("Altera TSE: Add main and header file for Altera Ethernet Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2be6d4d16a0849455a5c22490e3c5983495fed00 upstream.
Currently, due to the sequential use of min_t() and clamp_t() macros,
in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is not set, the logic
sets tx_max to 0. This is then used to allocate the data area of the
SKB requested later in cdc_ncm_fill_tx_frame().
This does not cause an issue presently because when memory is
allocated during initialisation phase of SKB creation, more memory
(512b) is allocated than is required for the SKB headers alone (320b),
leaving some space (512b - 320b = 192b) for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff830a5b5f len:184 put:172 \
head:ffff888119227c00 data:ffff888119227c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:110!
RIP: 0010:skb_panic+0x14f/0x160 net/core/skbuff.c:106
<snip>
Call Trace:
<IRQ>
skb_over_panic+0x2c/0x30 net/core/skbuff.c:115
skb_put+0x205/0x210 net/core/skbuff.c:1877
skb_put_zero include/linux/skbuff.h:2270 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1116 [inline]
cdc_ncm_fill_tx_frame+0x127f/0x3d50 drivers/net/usb/cdc_ncm.c:1293
cdc_ncm_tx_fixup+0x98/0xf0 drivers/net/usb/cdc_ncm.c:1514
By overriding the max value with the default CDC_NCM_NTB_MAX_SIZE_TX
when not offered through the system provided params, we ensure enough
data space is allocated to handle the CDC data, meaning no crash will
occur.
Cc: Oliver Neukum <oliver@neukum.org>
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20211202143437.1411410-1-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3d1d57debee2d342a47615707588b96658fabb85 upstream.
Since 66dfdff03d ("perf tools: Add Python 3 support") we don't use
the tools/build/feature/test-libpython-version.c version in any Makefile
feature check:
$ find tools/ -type f | xargs grep feature-libpython-version
$
The only place where this was used was removed in 66dfdff03d:
- ifneq ($(feature-libpython-version), 1)
- $(warning Python 3 is not yet supported; please set)
- $(warning PYTHON and/or PYTHON_CONFIG appropriately.)
- $(warning If you also have Python 2 installed, then)
- $(warning try something like:)
- $(warning $(and ,))
- $(warning $(and ,) make PYTHON=python2)
- $(warning $(and ,))
- $(warning Otherwise, disable Python support entirely:)
- $(warning $(and ,))
- $(warning $(and ,) make NO_LIBPYTHON=1)
- $(warning $(and ,))
- $(error $(and ,))
- else
- LDFLAGS += $(PYTHON_EMBED_LDFLAGS)
- EXTLIBS += $(PYTHON_EMBED_LIBADD)
- LANG_BINDINGS += $(obj-perf)python/perf.so
- $(call detected,CONFIG_LIBPYTHON)
- endif
And nowadays we either build with PYTHON=python3 or just install the
python3 devel packages and perf will build against it.
But the leftover feature-libpython-version check made the fast path
feature detection to break in all cases except when python2 devel files
were installed:
$ rpm -qa | grep python.*devel
python3-devel-3.9.7-1.fc34.x86_64
$ rm -rf /tmp/build/perf ; mkdir -p /tmp/build/perf ;
$ make -C tools/perf O=/tmp/build/perf install-bin
make: Entering directory '/var/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j32' parallel build
HOSTCC /tmp/build/perf/fixdep.o
<SNIP>
$ cat /tmp/build/perf/feature/test-all.make.output
In file included from test-all.c:18:
test-libpython-version.c:5:10: error: #error
5 | #error
| ^~~~~
$ ldd ~/bin/perf | grep python
libpython3.9.so.1.0 => /lib64/libpython3.9.so.1.0 (0x00007fda6dbcf000)
$
As python3 is the norm these days, fix this by just removing the unused
feature-libpython-version feature check, making the test-all fast path
to work with the common case.
With this:
$ rm -rf /tmp/build/perf ; mkdir -p /tmp/build/perf ;
$ make -C tools/perf O=/tmp/build/perf install-bin |& head
make: Entering directory '/var/home/acme/git/perf/tools/perf'
BUILD: Doing 'make -j32' parallel build
HOSTCC /tmp/build/perf/fixdep.o
HOSTLD /tmp/build/perf/fixdep-in.o
LINK /tmp/build/perf/fixdep
Auto-detecting system features:
... dwarf: [ on ]
... dwarf_getlocations: [ on ]
... glibc: [ on ]
$ ldd ~/bin/perf | grep python
libpython3.9.so.1.0 => /lib64/libpython3.9.so.1.0 (0x00007f58800b0000)
$ cat /tmp/build/perf/feature/test-all.make.output
$
Reviewed-by: James Clark <james.clark@arm.com>
Fixes: 66dfdff03d ("perf tools: Add Python 3 support")
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jaroslav Škarvada <jskarvad@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: https://lore.kernel.org/lkml/YaYmeeC6CS2b8OSz@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96db48c9d777a73a33b1d516c5cfed7a417a5f40 upstream.
This binding was already documented in phy.txt, commit 252ae5330d
("Documentation: devicetree: Add PHY no lane swap binding"), but got
accidently removed during YAML conversion in commit d8704342c1
("dt-bindings: net: Add a YAML schemas for the generic PHY options").
Note: 'enet-phy-lane-no-swap' and the absence of 'enet-phy-lane-swap' are
not identical, as the former one disable this feature, while the latter
one doesn't change anything.
Fixes: d8704342c1 ("dt-bindings: net: Add a YAML schemas for the generic PHY options")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211130082756.713919-1-alexander.stein@ew.tq-group.com
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6a631c0432dcccbcf45839016a07c015e335e9ae upstream.
The initial implementation of migrate_disable() for mainline was a
wrapper around preempt_disable(). RT kernels substituted this with
a real migrate disable implementation.
Later on mainline gained true migrate disable support, but the
documentation was not updated.
Update the documentation, remove the claims about migrate_disable()
mapping to preempt_disable() on non-PREEMPT_RT kernels.
Fixes: 74d862b682f51 ("sched: Make migrate_disable/enable() independent of RT")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20211127163200.10466-2-bigeasy@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 39bd54d43b3f8b3c7b3a75f5d868d8bb858860e7 upstream.
This reverts commit 239edf686c14a9ff926dec2f350289ed7adfefe2.
239edf686c14 ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated
bridge") added support for the Type 1 Expansion ROM BAR at config offset
0x38, based on the register being listed in the Marvell Armada A3720 spec.
But the spec doesn't document it at all for RC mode, and there is no ROM in
the SOC, so remove this emulation for now.
The PCI bridge which represents aardvark's PCIe Root Port has an Expansion
ROM Base Address register at offset 0x30, but its meaning is different than
PCI's Expansion ROM BAR register, although the layout is the same. (This
is why we thought it does the same thing.)
First: there is no ROM (or part of BootROM) in the A3720 SOC dedicated for
PCIe Root Port (or controller in RC mode) containing executable code that
would initialize the Root Port, suitable for execution in bootloader (this
is how Expansion ROM BAR is used on x86).
Second: in A3720 spec the register (address 0xD0070030) is not documented
at all for Root Complex mode, but similar to other BAR registers, it has an
"entangled partner" in register 0xD0075920, which does address translation
for the BAR in 0xD0070030:
- the BAR register sets the address from the view of PCIe bus
- the translation register sets the address from the view of the CPU
The other BAR registers also have this entangled partner, and they can be
used to:
- in RC mode: address-checking on the receive side of the RC (they can
define address ranges for memory accesses from remote Endpoints to the
RC)
- in Endpoint mode: allow the remote CPU to access memory on A3720
The Expansion ROM BAR has only the Endpoint part documented, but from the
similarities we think that it can also be used in RC mode in that way.
So either Expansion ROM BAR has different meaning (if the hypothesis above
is true), or we don't know it's meaning (since it is not documented for RC
mode).
Remove the register from the emulated bridge accessing functions.
[bhelgaas: summarize reason for removal (first paragraph)]
Fixes: 239edf686c14 ("PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge")
Link: https://lore.kernel.org/r/20211125160148.26029-3-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 23ec111bf3549aae37140330c31a16abfc172421 upstream.
When trying to dump VFs VSI RX/TX descriptors
using debugfs there was a crash
due to NULL pointer dereference in i40e_dbg_dump_desc.
Added a check to i40e_dbg_dump_desc that checks if
VSI type is correct for dumping RX/TX descriptors.
Fixes: 02e9c29081 ("i40e: debugfs interface")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9472335eaa1452b51dc8e8edaa1a342997cb80c7 upstream.
Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool):
mode0 mode3
eraseblock write speed 3220 KiB/s 4511 KiB/s
eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571 ("mtd: nand: fsmc: add support for SDR timings")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8aa55ab422d9d0d825ebfb877702ed661e96e682 upstream.
After setting pre-set combined to 16 queues and reserving 16 queues by
tc qdisc, pre-set maximum combined queues returned to default value
after VF reset being 4 and this generated errors during removing tc.
Fixed by removing clear num_req_queues before reset VF.
Fixes: e284fc2804 (i40e: Add and delete cloud filter)
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Bindushree P <Bindushree.p@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
