Instead of having all steering private name spaces and
steering module fields flat in mlx5_core_priv, we wrap
them in mlx5_flow_steering for better modularity and
API exposure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the set of arguments passed to mlx5_add_flow_rule
by introducing flow_spec structure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon Wunderlich says:
====================
This feature patchset includes the following changes:
- Cleanup work by Markus Pargmann and Sven Eckelmann (six patches)
- Initial Netlink support by Matthias Schiffer (two patches)
- Throughput Meter implementation by Antonio Quartulli, a kernel-space
traffic generator to estimate link speeds. This feature is useful on
low-end WiFi APs where running iperf or netperf from userspace
gives wrong results due to heavy userspace/kernelspace overhead.
(two patches)
- API clean-up work by Antonio Quartulli (one patch)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Qualcomm ARM Based Driver Updates for v4.8
* Rework of SCM driver
* Add file patterns for Qualcomm Maintainers entry
* Add worker for wcnss_ctrl signaling
* Fixes for smp2p
* Update smem_state properties to match documentation
* Add SCM Peripheral Authentication service
* Expose SCM PAS command 10 as a reset controller
* tag 'qcom-drivers-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
firmware: qcom: scm: Expose PAS command 10 as reset-controller
firmware: qcom: scm: Peripheral Authentication Service
soc: qcom: Update properties for smem state referencing
soc: qcom: smp2p: Drop io-accessors
soc: qcom: smp2p: Correct addressing of outgoing value
soc: qcom: wcnss_ctrl: Make wcnss_ctrl parent the other components
firmware: qcom: scm: Add support for ARM64 SoCs
firmware: qcom: scm: Convert to streaming DMA APIS
firmware: qcom: scm: Generalize shared error map
firmware: qcom: scm: Use atomic SCM for cold boot
firmware: qcom: scm: Convert SCM to platform driver
MAINTAINERS: Add file patterns for qcom device tree bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
SCPI updates and fixes for v4.8
1. Adds support for device power state management using generic power
domains and runtime PM
2. Other minor/miscellaneous fixes to the driver
* tag 'scpi-updates-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: scpi: add device power domain support using genpd
Documentation: add DT bindings for ARM SCPI power domains
firmware: arm_scpi: add support for device power state management
firmware: arm_scpi: make it depend on MAILBOX instead of ARM_MHU
firmware: arm_scpi: mark scpi_get_sensor_value as static
firmware: arm_scpi: remove dvfs_get packed structure
Signed-off-by: Olof Johansson <olof@lixom.net>
Add functions that iterate over lower devices and find port device.
As a dependency add netdev_for_each_all_lower_dev and
netdev_for_each_all_lower_dev_rcu macro with
netdev_all_lower_get_next and netdev_all_lower_get_next_rcu shelpers.
Also, add functions to return mlxsw struct according to lower device
found and mlxsw_port struct with a reference to lower device.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As vendor document indicate, when REF_CLK bit set 0, then DP
phy's REF_CLK should switch to 24M source clock.
But due to IC PHY layout mistaken, some chips need to flip this
bit(like RK3288), and unfortunately they didn't indicate in the
DP version register. That's why we have to make this little hack.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Tomasz Figa <tomasz.figa@chromium.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
ASoC: Add private data for HDMI CODEC callbacks
Allow the HDMI CODECs to get private data passed in in callbacks.
[airlied:
Add STI/mediatek patches from Arnd for drivers merged later in drm tree.]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* tag 'asoc-hdmi-codec-pdata' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound:
ASoC: hdmi-codec: callback function will be called with private data
If skb_clear_hash() was invoked due to mangling of relevant headers and
BPF program needs skb->hash later on, we can add a helper to trigger hash
recalculation via bpf_get_hash_recalc().
The helper will return the newly retrieved hash directly, but later access
can also be done via skb context again through skb->hash directly (inline)
without needing to call the helper once more.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extremely useful for setting packet type to host so i dont
have to modify the dst mac address using pedit (which requires
that i know the mac address)
Example usage:
tc filter add dev eth0 parent ffff: protocol ip pref 9 u32 \
match ip src 5.5.5.5/32 \
flowid 1:5 action skbedit ptype host
This will tag all packets incoming from 5.5.5.5 with type
PACKET_HOST
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial use for this is for PHYs that have a mode related to USB OTG.
There are several SoCs (e.g. TI OMAP and DA8xx) that have a mode setting
in the USB PHY to override OTG VBUS and ID signals.
Of course, the enum can be expaned in the future to include modes for
other types of PHYs as well.
Suggested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: David Lechner <david@lechnology.com>
The throughput meter module is a simple, kernel-space replacement for
throughtput measurements tool like iperf and netperf. It is intended to
approximate TCP behaviour.
It is invoked through batctl: the protocol is connection oriented, with
cumulative acknowledgment and a dynamic-size sliding window.
The test *can* be interrupted by batctl. A receiver side timeout avoids
unlimited waitings for sender packets: after one second of inactivity, the
receiver abort the ongoing test.
Based on a prototype from Edo Monticelli <montik@autistici.org>
Signed-off-by: Antonio Quartulli <antonio.quartulli@open-mesh.com>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
BATADV_CMD_GET_MESH_INFO is used to query basic information about a
batman-adv softif (name, index and MAC address for both the softif and
the primary hardif; routing algorithm; batman-adv version).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: Reduce the number of changes to
BATADV_CMD_GET_MESH_INFO, add missing kerneldoc, add policy for attributes]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
debugfs is currently severely broken virtually everywhere in the kernel
where files are dynamically added and removed (see
http://lkml.iu.edu/hypermail/linux/kernel/1506.1/02196.html for some
details). In addition to that, debugfs is not namespace-aware.
Instead of adding new debugfs entries, the whole infrastructure should be
moved to netlink. This will fix the long standing problem of large buffers
for debug tables and hard to parse text files.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven.eckelmann@open-mesh.com: Strip down patch to only add genl family,
add missing kerneldoc]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This replaces the polling work struct with a delayed work struct and add
a 10 ms delay between 2 poll cycles. This avoids to flood the device
with 'switch off'/'switch on' commands.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It used to be EXPORTed, but then EXPORT usage was cleaned up
(in 2012), without noticing that the function has no users at all
(and curiously, never had any users).
Delete it.
While at it, remove non-static "inline" hints on nearby functions:
these hints don't work across compilation units anyway,
and these functions are not used in their .c file, thus they are
never inlined. IOW: "inline" here does not help in any way.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Samuel Ortiz <sameo@linux.intel.com>
CC: Christophe Ricard <christophe.ricard@gmail.com>
CC: linux-wireless@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
igt likes to inject GPU hangs into its command streams. However, as we
expect these hangs, we don't actually want them recorded in the dmesg
output or stored in the i915_error_state (usually). To accommodate this
allow userspace to set a flag on the context that any hang emanating
from that context will not be recorded. We still do the error capture
(otherwise how do we find the guilty context and know its intent?) as
part of the reason for random GPU hang injection is to exercise the race
conditions between the error capture and normal execution.
v2: Split out the request->ringbuf error capture changes.
v3: Move the flag defines next to the intel_context->flags definition
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467616119-4093-9-git-send-email-chris@chris-wilson.co.uk
I don't think any single piece of the KVM/ARM code ever generated
as much hatred as the GIC emulation.
It was written by someone who had zero experience in modeling
hardware (me), was riddled with design flaws, should have been
scrapped and rewritten from scratch long before having a remote
chance of reaching mainline, and yet we supported it for a good
three years. No need to mention the names of those who suffered,
the git log is singing their praises.
Thankfully, we now have a much more maintainable implementation,
and we can safely put the grumpy old GIC to rest.
Fellow hackers, please raise your glass in memory of the GIC:
The GIC is dead, long live the GIC!
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Pull fuse fix from Miklos Szeredi:
"This makes sure userspace filesystems are not broken by the parallel
lookups and readdir feature"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: serialize dirops by default
netfilter uses multiple FWINV #defines with identical form that hide a
specific structure variable and dereference it with a invflags member.
$ git grep "#define FWINV"
include/linux/netfilter_bridge/ebtables.h:#define FWINV(bool,invflg) ((bool) ^ !!(info->invflags & invflg))
net/bridge/netfilter/ebtables.c:#define FWINV2(bool, invflg) ((bool) ^ !!(e->invflags & invflg))
net/ipv4/netfilter/arp_tables.c:#define FWINV(bool, invflg) ((bool) ^ !!(arpinfo->invflags & (invflg)))
net/ipv4/netfilter/ip_tables.c:#define FWINV(bool, invflg) ((bool) ^ !!(ipinfo->invflags & (invflg)))
net/ipv6/netfilter/ip6_tables.c:#define FWINV(bool, invflg) ((bool) ^ !!(ip6info->invflags & (invflg)))
net/netfilter/xt_tcpudp.c:#define FWINVTCP(bool, invflg) ((bool) ^ !!(tcpinfo->invflags & (invflg)))
Consolidate these macros into a single NF_INVF macro.
Miscellanea:
o Neaten the alignment around these uses
o A few lines are > 80 columns for intelligibility
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Leonard Crestez observed the following phenomenon: when using
hard interrupt triggers (the DRDY line coming out of an ST
sensor) sometimes a new value would arrive while reading the
previous value, due to latencies in the system.
We discovered that the ST hardware as far as can be observed
is designed for level interrupts: the DRDY line will be held
asserted as long as there are new values coming. The interrupt
handler should be re-entered until we're out of values to
handle from the sensor.
If interrupts were handled as occurring on the edges (usually
low-to-high) new values could appear and the line be held
asserted after that, and these values would be missed, the
interrupt handler would also lock up as new data was
available, but as no new edges occurs on the DRDY signal,
nothing happens: the edge detector only detects edges.
To counter this, do the following:
- Accept interrupt lines to be flagged as level interrupts
using IRQF_TRIGGER_HIGH and IRQF_TRIGGER_LOW. If the line
is marked like this (in the device tree node or ACPI
table or similar) it will be utilized as a level IRQ.
We mark the line with IRQF_ONESHOT and mask the IRQ
while processing a sample, then the top half will be
entered again if new values are available.
- If we are flagged as using edge interrupts with
IRQF_TRIGGER_RISING or IRQF_TRIGGER_FALLING: remove
IRQF_ONESHOT so that the interrupt line is not
masked while running the thread part of the interrupt.
This way we will never miss an interrupt, then introduce
a loop that polls the data ready registers repeatedly
until no new samples are available, then exit the
interrupt handler. This way we know no new values are
available when the interrupt handler exits and
new (edge) interrupts will be triggered when data arrives.
Take some extra care to update the timestamp in the poll
loop if this happens. The timestamp will not be 100%
perfect, but it will at least be closer to the actual
events. Usually the extra poll loop will handle the new
samples, but once in a blue moon, we get a new IRQ
while exiting the loop, before returning from the
thread IRQ bottom half with IRQ_HANDLED. On these rare
occasions, the removal of IRQF_ONESHOT means the
interrupt will immediately fire again.
- If no interrupt type is indicated from the DT/ACPI,
choose IRQF_TRIGGER_RISING as default, as this is necessary
for legacy boards.
Tested successfully on the LIS331DL and L3G4200D by setting
sampling frequency to 400Hz/800Hz and stressing the system:
extra reads in the threaded interrupt handler occurs.
Cc: Giuseppe Barba <giuseppe.barba@st.com>
Cc: Denis Ciocca <denis.ciocca@st.com>
Tested-by: Crestez Dan Leonard <cdleonard@gmail.com>
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
To allow creating more than one netdev over the same PCI function, we
change the driver such that global NIC resources are created once and
later be shared amongst all the mlx5e netdevs running over that port.
Move the CQ UAR, PD (pdn), Transport Domain (tdn), MKey resources from
being kept in the mlx5e priv part to a new resources structure
(mlx5e_resources) placed under the mlx5_core device.
This patch doesn't add any new functionality.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the commands to set and show the mode of SRIOV E-Switch, two modes
are supported:
* legacy: operating in the "old" L2 based mode (DMAC --> VF vport)
* switchdev: the E-Switch is referred to as whitebox switch configured
using standard tools such as tc, bridge, openvswitch etc. To allow
working with the tools, for each VF, a VF representor netdevice is
created by the E-Switch manager vendor device driver instance (e.g PF).
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new namespace (MLX5_FLOW_NAMESPACE_OFFLOADS) to be populated
with flow steering rules that deal with rules that have have to
be executed before the EN NIC steering rules are matched.
The namespace is located after the bypass name-space and before the
kernel name-space. Therefore, it precedes the HW processing done for
rules set for the kernel NIC name-space.
Under SRIOV, it would allow us to match on e-switch missed packet
and forward them to the relevant VF representor TIR.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patchset contains a new helper in drm_fb_cma_helper.c for suspend/
resume when using cma backed framebuffers.
* 'for-next' of http://git.agner.ch/git/linux-drm-fsl-dcu:
drm/fsl-dcu: disable vblank events on CRTC disable
drm/fsl-dcu: implement suspend/resume using atomic helpers
drm/fsl-dcu: use clk helpers
drm/fsl-dcu: move layer initialization to plane file
drm/fsl-dcu: store layer registers in soc_data
drm/fb_cma_helper: add suspend helper
here's a batch of i915 fixes for 4.7.
* tag 'drm-intel-fixes-2016-06-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
drm/i915: Removing PCI IDs that are no longer listed as Kabylake.
drm/i915: Add more Kabylake PCI IDs.
drm/i915: Avoid early timeout during AUX transfers
drm/i915/hsw: Avoid early timeout during LCPLL disable/restore
drm/i915/lpt: Avoid early timeout during FDI PHY reset
drm/i915/bxt: Avoid early timeout during PLL enable
drm/i915: Refresh cached DP port register value on resume
adding suspend and resume funtionality for extcon-adc-jack
driver to configure system wake up for extcon events,
also adding support to enable/disable system wakeup
through flag wakeup_source based on platform requirement.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
On Freescale i.MX7D platform, all clocks operations, including
enable/disable, rate change and re-parent, requires its parent
clock enable. Current clock core can not support it well.
This patch introduce a new flag CLK_OPS_PARENT_ENABLE to handle this
special case in clock core that enable its parent clock firstly for
each operation and disable it later after operation complete.
The patch part 1 fixes the possible disabling clocks while its parent
is off during kernel booting phase in clk_disable_unused_subtree().
Before the completion of kernel booting, clock tree is still not built
completely, there may be a case that the child clock is on but its
parent is off which could be caused by either HW initial reset state
or bootloader initialization.
Taking bootloader as an example, we may enable all clocks in HW by default.
And during kernel booting time, the parent clock could be disabled in its
driver probe due to calling clk_prepare_enable and clk_disable_unprepare.
Because it's child clock is only enabled in HW while its SW usecount
in clock tree is still 0, so clk_disable of parent clock will gate
the parent clock in both HW and SW usecount ultimately. Then there will
be a child clock is still on in HW but its parent is already off.
Later in clk_disable_unused(), this clock disable accessing while its
parent off will cause system hang due to the limitation of HW which
must require its parent on.
This patch simply enables the parent clock first before disabling
if flag CLK_OPS_PARENT_ENABLE is set in clk_disable_unused_subtree().
This is a simple solution and only affects booting time.
After kernel booting up the clock tree is already created, there will
be no case that child is off but its parent is off.
So no need do this checking for normal clk_disable() later.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull rockchip clk driver updates from Heiko Stuebner:
Placeholder for the rk3399 watchdog pclk, some newly exported
rk3228 clockids and a small fix for the not yet used spdif to
displayport clock on the rk3399.
* tag 'v4.8-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: fix incorrect rk3399 spdif-DPTX divider bits
clk: rockchip: export rk3228 MAC clocks
clk: rockchip: rename rk3228 sclk_macphy_50m to sclk_mac_extclk
clk: rockchip: export rk3228 audio clocks
clk: rockchip: include rk3228 downstream muxes into fractional dividers
clk: rockchip: fix incorrect rk3228 clock registers
clk: rockchip: add clock-ids for rk3228 MAC clocks
clk: rockchip: add clock-ids for rk3228 audio clocks
clk: rockchip: add a dummy clock for the watchdog pclk on rk3399
Pull tegra clk driver updates from Thierry Reding:
Fixes and enhancements mostly for Tegra210 clocks that allow DSI and
HDMI to work on Tegra X1. There's also a refactoring, including fixes,
the USB PLL.
* tag 'tegra-for-4.8-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
clk: tegra: Initialize UTMI PLL when enabling PLLU
clk: tegra: Micro-optimize Tegra210 clock setup
clk: tegra: Make sor_safe the parent of dpaux and dpaux1
clk: tegra: Mark timer clock as critical
clk: tegra: Enable sor1 and sor1_src on Tegra210
clk: tegra: Squash sor1 safe/brick/src into a single mux
clk: tegra: Disable spread spectrum on pll_d2
clk: tegra: Fixup post dividers on Tegra210
Trying to make the ISA and PCI init functionality common turned out
to be a bad idea, because the ISA path depends on external
functionality.
Restore the previous behavior and limit the refactoring to PCI
interrupts only.
Fixes: 1fcb6a813c "ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()"
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
power_supply_get_property() should ideally return -EAGAIN if it is
called while the power_supply is being registered. There was no way
previously to determine if use_cnt == 0 meant that the power_supply
wasn't fully registered yet, or if it had already been unregistered.
Add a new boolean to the power_supply struct to simply show if
registration is completed. Lastly, modify the check in
power_supply_show_property() to also ignore -EAGAIN when so it
doesn't complain about not returning the property.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Adds a bpf helper, bpf_skb_in_cgroup, to decide if a skb->sk
belongs to a descendant of a cgroup2. It is similar to the
feature added in netfilter:
commit c38c4597e4 ("netfilter: implement xt_cgroup cgroup2 path match")
The user is expected to populate a BPF_MAP_TYPE_CGROUP_ARRAY
which will be used by the bpf_skb_in_cgroup.
Modifications to the bpf verifier is to ensure BPF_MAP_TYPE_CGROUP_ARRAY
and bpf_skb_in_cgroup() are always used together.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a BPF_MAP_TYPE_CGROUP_ARRAY and its bpf_map_ops's implementations.
To update an element, the caller is expected to obtain a cgroup2 backed
fd by open(cgroup2_dir) and then update the array with that fd.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function to get a cgroup2 from a fd. It will be
stored in a bpf array (BPF_MAP_TYPE_CGROUP_ARRAY) which will
be introduced in the later patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're always tracing IPv4 or IPv6 addresses, so we can save a lot
of space on the ringbuffer by allocating the correct sockaddr size.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Cc: stable@vger.kernel.org
Fixes: 83a712e0af "sunrpc: add some tracepoints around ..."
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
