This driver is the only user of of_drm_find_panel() which prints an
error before doing probe deferral, yielding messages like this on boot,
before eventually succeeding:
[ 2.234271] [drm:rockchip_dp_probe] *ERROR* failed to find panel
...
[ 4.797539] [drm:rockchip_dp_probe] *ERROR* failed to find panel
...
Let's just drop the message.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
vblank should be enabled regardless of whether an event
is expected back. This is especially important for a cursor
plane.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chip.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Remove the delayed worker, opting instead for the non-delayed
variety. Also introduce a lock to ensure we don't have races
with the worker and psr_state. Finally, cancel and wait for
the worker to finish when disabling the bridge.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The handling of psr state is racey, shore that up with
a per-psr driver lock.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
This patch converts the psr_list_mutex to a spinlock and locks
all access to psr_list to avoid races (however unlikely they
were).
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Alway enable the PSR function for Rockchip analogix_dp driver. If panel
don't support PSR, then the core analogix_dp would ignore this setting.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The full name of PSR is Panel Self Refresh, panel device could refresh
itself with the hardware framebuffer in panel, this would make lots of
sense to save the power consumption.
This patch have exported two symbols for platform driver to implement
the PSR function in hardware side:
- analogix_dp_active_psr()
- analogix_dp_inactive_psr()
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
The PSR driver have exported four symbols for specific device driver, and
it's safe to call them in interrupt context:
- rockchip_drm_psr_register()
- rockchip_drm_psr_unregister()
- rockchip_drm_psr_enable()
- rockchip_drm_psr_disable()
- rockchip_drm_psr_flush()
Encoder driver should call the register/unregister interfaces to hook
itself into common PSR driver, encoder have implement the 'psr_set'
callback which use the set PSR state in hardware side.
Crtc driver would call the enable/disable interfaces when vblank is
enable/disable, after that the common PSR driver would call the encoder
registered callback to set the PSR state.
Fb driver would call the flush interface in 'fb->dirty' callback, this
helper function would force all PSR enabled encoders to exit from PSR
for 3 seconds.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
[seanpaul removed leftover psr_enabled/psr_work kruft from drm_vop.c]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
VOP have integrated a hardware counter which indicate the exact display
line that vop is scanning. And if we're interested in a specific line,
we can set the line number to vop line_flag register, and then vop would
generate a line_flag interrupt for it.
For example eDP PSR function is interested in the vertical blanking
period, then driver could set the line number to zero.
This patch have exported a symbol that allow other driver to listen the
line flag event with given timeout limit:
- rockchip_drm_wait_line_flag()
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Instead of just preparing the panel on bind, actually prepare/unprepare
during modeset/disable. The panel must be prepared in order to read hpd
status and edid, so we need to keep state around the prepares in order
to ensure we don't accidentally turn the panel off at the wrong time.
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Tested-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
There are two VOP in rk3399 chip, respectively VOP_BIG and VOP_LIT.
most registers layout of this two vop is same, their framework are both
VOP_FULL, the Major differences of this two is that:
VOP_BIG max output resolution is 4096x2160.
VOP_LIT max output resolution is 2560x1600
VOP_BIG support four windows.
VOP_LIT only support two windows.
RK3399 vop register layout is similar with rk3288, so some feature
can reuse with rk3288.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Some new vop register support mask, bit[16-31] is mask,
bit[0-15] is value, the mask is correspond to the value.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
[seanpaul masked 'v' per tfiga's review comments]
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
No functional changes, sort the vop registers to make
code more readable.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
[seanpaul resolved conflict with name change from _3066 to _3036]
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Thanks to Ville for suggesting this as a potential solution to pipe
underruns on Skylake.
On Skylake all of the registers for configuring planes, including the
registers for configuring their watermarks, are double buffered. New
values written to them won't take effect until said registers are
"armed", which is done by writing to the PLANE_SURF (or in the case of
cursor planes, the CURBASE register) register.
With this in mind, up until now we've been updating watermarks on skl
like this:
non-modeset {
- calculate (during atomic check phase)
- finish_atomic_commit:
- intel_pre_plane_update:
- intel_update_watermarks()
- {vblank happens; new watermarks + old plane values => underrun }
- drm_atomic_helper_commit_planes_on_crtc:
- start vblank evasion
- write new plane registers
- end vblank evasion
}
or
modeset {
- calculate (during atomic check phase)
- finish_atomic_commit:
- crtc_enable:
- intel_update_watermarks()
- {vblank happens; new watermarks + old plane values => underrun }
- drm_atomic_helper_commit_planes_on_crtc:
- start vblank evasion
- write new plane registers
- end vblank evasion
}
Now we update watermarks atomically like this:
non-modeset {
- calculate (during atomic check phase)
- finish_atomic_commit:
- intel_pre_plane_update:
- intel_update_watermarks() (wm values aren't written yet)
- drm_atomic_helper_commit_planes_on_crtc:
- start vblank evasion
- write new plane registers
- write new wm values
- end vblank evasion
}
modeset {
- calculate (during atomic check phase)
- finish_atomic_commit:
- crtc_enable:
- intel_update_watermarks() (actual wm values aren't written
yet)
- drm_atomic_helper_commit_planes_on_crtc:
- start vblank evasion
- write new plane registers
- write new wm values
- end vblank evasion
}
So this patch moves all of the watermark writes into the right place;
inside of the vblank evasion where we update all of the registers for
each plane. While this patch doesn't fix everything, it does allow us to
update the watermark values in the way the hardware expects us to.
Changes since original patch series:
- Remove mutex_lock/mutex_unlock since they don't do anything and we're
not touching global state
- Move skl_write_cursor_wm/skl_write_plane_wm functions into
intel_pm.c, make externally visible
- Add skl_write_plane_wm calls to skl_update_plane
- Fix conditional for for loop in skl_write_plane_wm (level < max_level
should be level <= max_level)
- Make diagram in commit more accurate to what's actually happening
- Add Fixes:
Changes since v1:
- Use IS_GEN9() instead of IS_SKYLAKE() since these fixes apply to more
then just Skylake
- Update description to make it clear this patch doesn't fix everything
- Check if pipes were actually changed before writing watermarks
Changes since v2:
- Write PIPE_WM_LINETIME during vblank evasion
Changes since v3:
- Rebase against new SAGV patch changes
Changes since v4:
- Add a parameter to choose what skl_wm_values struct to use when
writing new plane watermarks
Changes since v5:
- Remove cursor ddb entry write in skl_write_cursor_wm(), defer until
patch 6
- Write WM_LINETIME in intel_begin_crtc_commit()
Changes since v6:
- Remove redundant dirty_pipes check in skl_write_plane_wm (we check
this in all places where we call this function, and it was supposed
to have been removed earlier anyway)
- In i9xx_update_cursor(), use dev_priv->info.gen >= 9 instead of
IS_GEN9(dev_priv). We do this everywhere else and I'd imagine this
needs to be done for gen10 as well
Changes since v7:
- Fix rebase fail (unused variable obj)
- Make struct skl_wm_values *wm const
- Fix indenting
- Use INTEL_GEN() instead of dev_priv->info.gen
Changes since v8:
- Don't forget calls to skl_write_plane_wm() when disabling planes
- Use INTEL_GEN(), not INTEL_INFO()->gen in intel_begin_crtc_commit()
Fixes: 2d41c0b59a ("drm/i915/skl: SKL Watermark Computation")
Signed-off-by: Lyude <cpaul@redhat.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471884608-10671-1-git-send-email-cpaul@redhat.com
Link: http://patchwork.freedesktop.org/patch/msgid/1471884608-10671-1-git-send-email-cpaul@redhat.com
This is mostly code churn, with exception of a few places:
- intel_display.c has changes in intel_sanitize_encoder
- intel_ddi.c has intel_ddi_fdi_disable calling intel_ddi_post_disable,
and required a function change. Also affects intel_display.c
- intel_dp_mst.c passes a NULL crtc_state and conn_state to
intel_ddi_post_disable for shutting down the real encoder.
If we would pass conn_state, then conn_state->connector !=
intel_dig_port->connector and conn_state->best_encoder !=
to_intel_encoder(intel_dig_port).
We also shouldn't pass crtc_state, because in that case the
disabling sequence may potentially be different depending on
which crtc is disabled last. Nice way to introduce bugs.
No other functional changes are done, diff stat is already huge.
Each encoder type will need to be fixed to use the atomic states
separately.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470755054-32699-6-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were using the same mask twice. Looking at radeon, it seems
we should be using HDMI_AVI_INFO_CONT instead as the second mask.
Being there, fix typos in comments and improved readability.
I haven't looked at other DCEs, the mask may also be wrong for them.
Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
AMDGPU_GEM_CREATE_NO_CPU_ACCESS and AMDGPU_GEM_CREATE_CPU_ACCESS_REQUIRED are
obviously mutual exclusive. So stop adding a dummy entry without effect when
both are specified.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
V2:
1. use mutex instead of spinlock for shadow list, since its process could
sleep.
2. move list_del to bo destroy phase.
Signed-off-by: Chunming Zhou <David1.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
