Get the reset control properties for the QSPI controller and bring them
out of reset. Most will have just one reset bit, but there is an additional
OCP reset bit that is used ECC. The OCP reset bit will also need to get
de-asserted as well. [1]
The reason this patch is needed is in the case where a bootloader leaves
the QSPI controller in a reset state, or a state where init cannot occur
successfully, the patch will put the QSPI controller into a clean state.
[1] https://www.intel.com/content/www/us/en/programmable/hps/arria-10/hps.html#reg_soc_top/sfo1429890575955.html
Suggested-by: Tien-Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
[tudor.ambarus@microchip.com: declare rstc and rstc_ocp on the same line]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
The QSPI module can have an optional reset signals that will hold the
module in a reset state.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
IS25LP256 gets BFPT_DWORD1_ADDRESS_BYTES_3_ONLY from BFPT table for
address width. But in actual fact the flash can support 4-byte address.
Use a post bfpt fixup hook to overwrite the address width advertised by
the BFPT.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
RK809 and RK817 are power management IC chips for multimedia products.
most of their functions and registers are same, including the clkout
funciton.
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
RK809 and RK817 are power management IC chips for multimedia products.
Most of their functions and registers are same, including the rtc.
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the rk809 and rk817 regulator driver.
Their specifications are as follows：
1. The RK809 and RK809 consist of 5 DCDCs, 9 LDOs
and have the same registers for these components except dcdc5.
2. The dcdc5 is a boost dcdc for RK817 and is a buck for RK809.
3. The RK817 has one switch but The Rk809 has two.
The output voltages are configurable and are meant to supply power
to the main processor and other components.
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Acked-by: Mark Brown <broonie@kernel.org>
[rebased on top of 5.2-rc1]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RK809 and RK817 are a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators
- RTC
- Clocking
Both RK809 and RK817 chips are using a similar register map,
so we can reuse the RTC and Clocking functionality.
Most of regulators have a some implementation also.
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We no longer have platform data in at24, so this comment is invalid.
Make it refer to device tree & properties instead.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
bio_flush_dcache_pages() is unused. Remove it.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add COMPILE_TEST dependency to force exynos driver to
built for more than arm and to built modules
that otherwise required other symbols to be de-selected.
This will increase build coverage of the exynos driver
thus allowing most trivial build errors to be detected/fixed early.
This introduces one warning when built using sh:
exynos7_drm_decon.c: In function ‘decon_remove’:
exynos7_drm_decon.c:769:24: warning: unused variable ‘ctx’
struct decon_context *ctx = dev_get_drvdata(&pdev->dev);
This is due to the definition of iounmap() in sh,
and nothing that exynos driver can fix.
Include fix of exynos build for alpha.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Rename the thermal documentation files to ReST, add an
index for them and adjust in order to produce a nice html
output via the Sphinx build system.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Now that the governor table is in place and the macro allows to browse the
table, declare the governor so the entry is added in the governor table
in the init section.
The [un]register_thermal_governors function does no longer need to use the
exported [un]register thermal governor's specific function which in turn
call the [un]register_thermal_governor. The governors are fully
self-encapsulated.
The cyclic dependency is no longer needed, remove it.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Currently the governors are declared in their respective files but they
export their [un]register functions which in turn call the [un]register
governors core's functions. That implies a cyclic dependency which is
not desirable. There is a way to self-encapsulate the governors by letting
them to declare themselves in a __init section table.
Define the table in the asm generic linker description like the other
tables and provide the specific macros to deal with.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
As per binding documentation [1], the DWC3 core should have the "ref",
"bus_early" and "suspend" clocks. As explained in the binding, those
clocks are required for new platforms but not for existing platforms
before commit fe8abf332b ("usb: dwc3: support clocks and resets for
DWC3 core").
However, as those clocks are really treated as required, this ends with
having some annoying messages when the "rockchip,rk3399-dwc3" is used:
[ 1.724107] dwc3 fe800000.dwc3: Failed to get clk 'ref': -2
[ 1.731893] dwc3 fe900000.dwc3: Failed to get clk 'ref': -2
[ 2.495937] dwc3 fe800000.dwc3: Failed to get clk 'ref': -2
[ 2.647239] dwc3 fe900000.dwc3: Failed to get clk 'ref': -2
In order to remove those annoying messages, update the DWC3 hardware
module node and add all the required clocks. With this change, both, the
glue node and the DWC3 core node, have the clocks defined, but that's
not really a problem and there isn't a side effect on do this. So, we
can get rid of the annoying get clk error messages.
[1] Documentation/devicetree/bindings/usb/dwc3.txt
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Return the engine type from the function looking at the registers, and
just derive the DMA mask from that in the one place we care.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These days drivers are not required to fallback to smaller DMA masks,
but can just set the largest mask they support, removing the need for
this trial and error logic.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return the engine type from the function looking at the registers, and
just derive the DMA mask from that in the one place we care.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These days drivers are not required to fallback to smaller DMA masks,
but can just set the largest mask they support, removing the need for
this trial and error logic.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the try_encoder_cmd is identical for many drivers, there are now
helpers for this function in the mem2mem core. Use the helper in
allegro.
This fixes the v4l2-compliance test regarding V4L2_ENC_CMD_STOP, because
the allegro-specific function rejected invalid flags.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Change devm_k*alloc to k*alloc to manually allocate memory
The manual allocation and freeing of memory is necessary because when
the USB radio is disconnected, the memory associated with devm_k*alloc
is freed. Meaning if we still have unresolved references to the radio
device, then we get use-after-free errors.
This patch fixes this by manually allocating memory, and freeing it in
the v4l2.release callback that gets called when the last radio device
exits.
Reported-and-tested-by: syzbot+a4387f5b6b799f6becbf@syzkaller.appspotmail.com
Signed-off-by: Luke Nowakowski-Krijger <lnowakow@eng.ucsd.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: cleaned up two small checkpatch.pl warnings]
[hverkuil-cisco@xs4all.nl: prefix subject with driver name]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Prefer KEY_NUMERIC_* for number buttons on remotes. Now all the remotes
use KEY_NUMERIC_[0-9] for the number buttons rather than keys that
could be affected by modifiers (Caps-Lock, or Num-Lock) or regional
keymaps.
Created using:
sed -i 's/KEY_\([0-9]\) /KEY_NUMERIC_\1 /' *.c
sed -i 's/KEY_\([0-9]\)}/KEY_NUMERIC_\1}/' *.c
sed -i 's/``KEY_\([0-9]\)/``KEY_NUMERIC_\1/' Documentation/media/uapi/rc/rc-tables.rst
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Over time, dvb_frontend_handle_ioctl() has grown to the point where
we now get a warning from the compiler about excessive stack usage:
drivers/media/dvb-core/dvb_frontend.c: In function 'dvb_frontend_handle_ioctl':
drivers/media/dvb-core/dvb_frontend.c:2692:1: error: the frame size of 1048 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Almost all of this is used by the dtv_frontend_properties structure
in the FE_GET_PROPERTY and FE_GET_FRONTEND commands. Splitting those
into separate function reduces the stack usage of the main function
to just 136 bytes, the others are under 500 each.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
During suspend/resume, mtk_eint_mask may be called while
wake_mask is active. For example, this happens if a wake-source
with an active interrupt handler wakes the system:
irq/pm.c:irq_pm_check_wakeup would disable the interrupt, so
that it can be handled later on in the resume flow.
However, this may happen before mtk_eint_do_resume is called:
in this case, wake_mask is loaded, and cur_mask is restored
from an older copy, re-enabling the interrupt, and causing
an interrupt storm (especially for level interrupts).
Step by step, for a line that has both wake and interrupt enabled:
1. cur_mask[irq] = 1; wake_mask[irq] = 1; EINT_EN[irq] = 1 (interrupt
enabled at hardware level)
2. System suspends, resumes due to that line (at this stage EINT_EN
== wake_mask)
3. irq_pm_check_wakeup is called, and disables the interrupt =>
EINT_EN[irq] = 0, but we still have cur_mask[irq] = 1
4. mtk_eint_do_resume is called, and restores EINT_EN = cur_mask, so
it reenables EINT_EN[irq] = 1 => interrupt storm as the driver
is not yet ready to handle the interrupt.
This patch fixes the issue in step 3, by recording all mask/unmask
changes in cur_mask. This also avoids the need to read the current
mask in eint_do_suspend, and we can remove mtk_eint_chip_read_mask
function.
The interrupt will be re-enabled properly later on, sometimes after
mtk_eint_do_resume, when the driver is ready to handle it.
Fixes: 58a5e1b64b ("pinctrl: mediatek: Implement wake handler and suspend resume")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to support multiple CEC devices for an HDMI connector,
and to support cec_connector_info, drivers should use either a
cec_notifier_conn_(un)register pair of functions (HDMI drivers)
or a cec_notifier_cec_adap_(un)register pair (CEC adapter drivers).
This replaces cec_notifier_get_conn/cec_notifier_put.
For CEC adapters it is also no longer needed to call cec_notifier_register,
cec_register_cec_notifier and cec_notifier_unregister. This is now
all handled internally by the new functions.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Define struct cec_connector_info in media/cec.h and define
CEC_CAP_CONNECTOR_INFO. In a later patch this will be moved to
uapi/linux/cec.h.
The CEC_CAP_CONNECTOR_INFO capability can be set by drivers, but
cec_allocate_adapter() will remove it again until the public API
for this can be enabled once all drm drivers wire this up correctly.
Also add the cec_fill_conn_info_from_drm and cec_s_conn_info functions,
which are needed by drm drivers to fill in the cec_connector info
based on a drm_connector.
The cec_notifier_(un)register and cec_register_cec_notifier
prototypes were moved from cec-notifier.h to cec.h since cec.h no longer
includes cec-notifier.h. These headers included each other before,
which caused various problems.
Due to these changes the seco-cec driver was changed as well: it
should include cec-notifier.h, not cec.h.
Signed-off-by: Dariusz Marcinkiewicz <darekm@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
dev -> hdmi_dev
conn -> conn_name
Check if n->conn_name is not NULL before calling strcmp.
Check the result of kstrdup, and clean up on error.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Export all configuration space access APIs and also other APIs to
support host controller drivers of dwc core based implementations while
adding support for .remove() hook to build their respective drivers as
modules.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
