Cypress' HyperBus is Low Signal Count, High Performance Double Data Rate
Bus interface between a host system master and one or more slave
interfaces. HyperBus is used to connect microprocessor, microcontroller,
or ASIC devices with random access NOR flash memory (called HyperFlash)
or self refresh DRAM (called HyperRAM).
Its a 8-bit data bus (DQ[7:0]) with Read-Write Data Strobe (RWDS)
signal and either Single-ended clock(3.0V parts) or Differential clock
(1.8V parts). It uses ChipSelect lines to select b/w multiple slaves.
At bus level, it follows a separate protocol described in HyperBus
specification[1].
HyperFlash follows CFI AMD/Fujitsu Extended Command Set (0x0002) similar
to that of existing parallel NORs. Since HyperBus is x8 DDR bus,
its equivalent to x16 parallel NOR flash with respect to bits per clock
cycle. But HyperBus operates at >166MHz frequencies.
HyperRAM provides direct random read/write access to flash memory
array.
But, HyperBus memory controllers seem to abstract implementation details
and expose a simple MMIO interface to access connected flash.
Add support for registering HyperFlash devices with MTD framework. MTD
maps framework along with CFI chip support framework are used to support
communicating with flash.
Framework is modelled along the lines of spi-nor framework. HyperBus
memory controller (HBMC) drivers calls hyperbus_register_device() to
register a single HyperFlash device. HyperFlash core parses MMIO access
information from DT, sets up the map_info struct, probes CFI flash and
registers it with MTD framework.
Some HBMC masters need calibration/training sequence[3] to be carried
out, in order for DLL inside the controller to lock, by reading a known
string/pattern. This is done by repeatedly reading CFI Query
Identification String. Calibration needs to be done before trying to detect
flash as part of CFI flash probe.
HyperRAM is not supported at the moment.
HyperBus specification can be found at[1]
HyperFlash datasheet can be found at[2]
[1] https://www.cypress.com/file/213356/download
[2] https://www.cypress.com/file/213346/download
[3] http://www.ti.com/lit/ug/spruid7b/spruid7b.pdf
Table 12-5741. HyperFlash Access Sequence
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
HyperFlash devices are compliant with CFI AMD/Fujitsu Extended Command
Set (0x0002) for flash operations, therefore
drivers/mtd/chips/cfi_cmdset_0002.c can be used as is. But these devices
do not support DQ polling method of determining chip ready/good status.
These flashes provide Status Register whose bits can be polled to know
status of flash operation.
Cypress HyperFlash datasheet here[1], talks about CFI Amd/Fujitsu
Extended Query version 1.5. Bit 0 of "Software Features supported" field
of CFI Primary Vendor-Specific Extended Query table indicates
presence/absence of status register and Bit 1 indicates whether or not
DQ polling is supported. Using these bits, its possible to determine
whether flash supports DQ polling or need to use Status Register.
Add support for polling Status Register to know device ready/status of
erase/write operations when DQ polling is not supported.
Print error messages on erase/program failure by looking at related
Status Register bits.
[1] https://www.cypress.com/file/213346/download
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tokunori Ikegami <ikegami.t@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch removes the error branch for (queue > ar->hw->queues).
It is no longer needed anymore as the "queue" value is validated by
cfg80211's parse_txq_params() before the driver code gets called.
Some background:
In the old days (linux 2.6 and early 3.x), the parse_txq_params()
function did not verify the "queue" value. That's why these drivers
had to do it.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Because PPB unlocking unlocks the whole chip cfi_ppb_unlock() needs to
remember the locked status for each sector so it can re-lock the
unaddressed sectors. Dynamically calculate the maximum number of sectors
rather than using a hardcoded value that is too small for larger chips.
Tested with Spansion S29GL01GS11TFI flash device.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch follows Alan Stern's recent patch:
"p54: Fix race between disconnect and firmware loading"
that overhauled carl9170 buggy firmware loading and driver
unbinding procedures.
Since the carl9170 code was adapted from p54 it uses the
same functions and is likely to have the same problem, but
it's just that the syzbot hasn't reproduce them (yet).
a summary from the changes (copied from the p54 patch):
* Call usb_driver_release_interface() rather than
device_release_driver().
* Lock udev (the interface's parent) before unbinding the
driver instead of locking udev->parent.
* During the firmware loading process, take a reference
to the USB interface instead of the USB device.
* Don't take an unnecessary reference to the device during
probe (and then don't drop it during disconnect).
and
* Make sure to prevent use-after-free bugs by explicitly
setting the driver context to NULL after signaling the
completion.
Cc: <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 3c0efb745a ("ath9k: discard undersized packets")
the lower bound of RX packets was set to 10 (min ACK size) to
filter those that would otherwise be treated as invalid at
mac80211.
Alas, short radar pulses are reported as PHY_ERROR frames
with length set to 3. Therefore their detection stopped
working after that commit.
NOTE: ath9k drivers built thereafter will not pass DFS
certification.
This extends the criteria for short packets to explicitly
handle PHY_ERROR frames.
Fixes: 3c0efb745a ("ath9k: discard undersized packets")
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Document how to test ext4, f2fs, and ubifs encryption with xfstests.
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
fscrypt only uses SHA-256 for AES-128-CBC-ESSIV, which isn't the default
and is only recommended on platforms that have hardware accelerated
AES-CBC but not AES-XTS. There's no link-time dependency, since SHA-256
is requested via the crypto API on first use.
To reduce bloat, we should limit FS_ENCRYPTION to selecting the default
algorithms only. SHA-256 by itself isn't that much bloat, but it's
being discussed to move ESSIV into a crypto API template, which would
incidentally bring in other things like "authenc" support, which would
all end up being built-in since FS_ENCRYPTION is now a bool.
For Adiantum encryption we already just document that users who want to
use it have to enable CONFIG_CRYPTO_ADIANTUM themselves. So, let's do
the same for AES-128-CBC-ESSIV and CONFIG_CRYPTO_SHA256.
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Now that we not only track the presence of multicast listeners but also
multicast routers we can safely apply group-aware multicast-to-unicast
forwarding to packets with a destination address of scope greater than
link-local as well.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
To be able to apply our group aware multicast optimizations to packets
with a scope greater than link-local we need to not only keep track of
multicast listeners but also multicast routers.
With this patch a node detects the presence of multicast routers on
its segment by checking if
/proc/sys/net/ipv{4,6}/conf/<bat0|br0(bat)>/mc_forwarding is set for one
thing. This option is enabled by multicast routing daemons and needed
for the kernel's multicast routing tables to receive and route packets.
For another thing if a bridge is configured on top of bat0 then the
presence of an IPv6 multicast router behind this bridge is currently
detected by checking for an IPv6 multicast "All Routers Address"
(ff02::2). This should later be replaced by querying the bridge, which
performs proper, RFC4286 compliant Multicast Router Discovery (our
simplified approach includes more hosts than necessary, most notably
not just multicast routers but also unicast ones and is not applicable
for IPv4).
If no multicast router is detected then this is signalized via the new
BATADV_MCAST_WANT_NO_RTR4 and BATADV_MCAST_WANT_NO_RTR6
multicast tvlv flags.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because we don't care if debugfs works or not, this trickles back a bit
so we can clean things up by making some functions return void instead
of an error value that is never going to fail.
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <a@unstable.cc>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: b.a.t.m.a.n@lists.open-mesh.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[sven@narfation.org: drop unused variables]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
When a bridge is added on top of bat0 we set the WANT_ALL_UNSNOOPABLES
flag. Which means we sign up for all traffic for ff02::1/128 and
224.0.0.0/24.
When the node itself had IPv6 enabled or joined a group in 224.0.0.0/24
itself then so far this would result in a multicast TT entry which is
redundant to the WANT_ALL_UNSNOOPABLES.
With this patch such redundant TT entries are avoided.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Instead of collecting multicast MAC addresses from the netdev hw mc
list collect a node's multicast listeners from the IP lists and convert
those to MAC addresses.
This allows to exclude addresses of specific scope later. On a
multicast MAC address the IP destination scope is not visible anymore.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Commit 9da21b1509 ("EDAC: Poll timeout cannot be zero, p2") assumes
edac_mc_poll_msec to be unsigned long, but the type of the variable still
remained as int. Setting edac_mc_poll_msec can trigger out-of-bounds
write.
Reproducer:
# echo 1001 > /sys/module/edac_core/parameters/edac_mc_poll_msec
KASAN report:
BUG: KASAN: global-out-of-bounds in edac_set_poll_msec+0x140/0x150
Write of size 8 at addr ffffffffb91b2d00 by task bash/1996
CPU: 1 PID: 1996 Comm: bash Not tainted 5.2.0-rc6+ #23
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014
Call Trace:
dump_stack+0xca/0x13e
print_address_description.cold+0x5/0x246
__kasan_report.cold+0x75/0x9a
? edac_set_poll_msec+0x140/0x150
kasan_report+0xe/0x20
edac_set_poll_msec+0x140/0x150
? dimmdev_location_show+0x30/0x30
? vfs_lock_file+0xe0/0xe0
? _raw_spin_lock+0x87/0xe0
param_attr_store+0x1b5/0x310
? param_array_set+0x4f0/0x4f0
module_attr_store+0x58/0x80
? module_attr_show+0x80/0x80
sysfs_kf_write+0x13d/0x1a0
kernfs_fop_write+0x2bc/0x460
? sysfs_kf_bin_read+0x270/0x270
? kernfs_notify+0x1f0/0x1f0
__vfs_write+0x81/0x100
vfs_write+0x1e1/0x560
ksys_write+0x126/0x250
? __ia32_sys_read+0xb0/0xb0
? do_syscall_64+0x1f/0x390
do_syscall_64+0xc1/0x390
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7fa7caa5e970
Code: 73 01 c3 48 8b 0d 28 d5 2b 00 f7 d8 64 89 01 48 83 c8 ff c3 66 0f 1f 44 00 00 83 3d 99 2d 2c 00 00 75 10 b8 01 00 00 00 04
RSP: 002b:00007fff6acfdfe8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007fa7caa5e970
RDX: 0000000000000005 RSI: 0000000000e95c08 RDI: 0000000000000001
RBP: 0000000000e95c08 R08: 00007fa7cad1e760 R09: 00007fa7cb36a700
R10: 0000000000000073 R11: 0000000000000246 R12: 0000000000000005
R13: 0000000000000001 R14: 00007fa7cad1d600 R15: 0000000000000005
The buggy address belongs to the variable:
edac_mc_poll_msec+0x0/0x40
Memory state around the buggy address:
ffffffffb91b2c00: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
ffffffffb91b2c80: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa
>ffffffffb91b2d00: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
^
ffffffffb91b2d80: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
ffffffffb91b2e00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Fix it by changing the type of edac_mc_poll_msec to unsigned int.
The reason why this patch adopts unsigned int rather than unsigned long
is msecs_to_jiffies() assumes arg to be unsigned int. We can avoid
integer conversion bugs and unsigned int will be large enough for
edac_mc_poll_msec.
Reviewed-by: James Morse <james.morse@arm.com>
Fixes: 9da21b1509 ("EDAC: Poll timeout cannot be zero, p2")
Signed-off-by: Eiichi Tsukata <devel@etsukata.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Convert Conexant Digicolor SoC bindings to DT schema format using json-schema.
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert NXP LPC32xx SoC bindings to DT schema format using json-schema.
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Convert MOXA ART SoC bindings to DT schema format using json-schema.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a structure for power parameters including base,
offset, limit and a function to get tx power parameters.
Then, refine flow to get tx power index through the
function.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since this macro definition has different values in different chipset,
the current defined macro value is for 8822b. This will cause the
settings of 8822c be incorrect.
Remove RTW_MAX_POWER_INDEX and use max_power_index in struct rtw_chip_info
to make sure the value of different chipset is right.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support more regulatory domains including IC, KCC,
ACMA, CHILE, UKRAINE, and MEXICO. Corresponding tx
power limits for these regulatory domains are added
in tx power limit table. Besides, tx power limits in
some case are also updated to follow RF v20 for better
tx power indexes.
Channel plan mapping table are upgraded to consider
more 2G and 5G channel plans combination cases. It
allow us to identify different situations more accuratly
by channel plan IDs. In addition, mapping table for
country code and channel plan ID and mapping table
for country code and tx power limit are also updated
to follow RF v20. It allow the new enrties in tx power
limit table to be applied correctly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If phy rate is decreased, sub bandwidth may be chosen by RA.
We consider possible power limits and apply the min one;
otherwise, the tx power index may be larger than spec.
And we cross-reference power limits of vht and ht with
20/40M bandwidth in 5G to avoid values are not assigned.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we are loading tx power limit from the power limit table, compare
the world-wide limit with the current limit and choose the lowest power
limit for the world-wide power settings.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Tx power limit is stored separately by 2G and 5G.
But driver did not get tx power limit from 5G and causes incorrect tx
power. Check if the channel is beyond 2G and get the corresponding tx
power limit.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rename the function names to make them have the same prefix "rtw_phy"
for the tx power setting routines. Only the function names and
corresponding identation are modified.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The type change from (void *) to (struct rtw_dev *) is redundant.
Just pass the right type and compiler can check that for us.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some functions that should be static are unnecessarily exposed, remove
their declaration in header file phy.h.
After resolving their declaration order, they can be declared as static.
So this commit changes nothing except the order and marking them static.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Julian Wiedmann says:
====================
s390/qeth: updates 2019-06-27
please apply another round of qeth updates for net-next.
This completes the conversion of the control path to use dynamically
allocated cmd buffers, along with some fine-tuning for the route
validation fix that recently went into -net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The cast type currently gets selected in .ndo_start_xmit, and is then
piped through several layers until it's stored into the HW header.
Push the selection down into qeth_l?_fill_header() to (1) reduce the
number of xmit-wide parameters, and (2) merge the two route validation
checks into just one.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As follow-up to commit 0cd6783d3c ("s390/qeth: check dst entry before use"),
consolidate the dst_check() logic into a single helper and add a wrapper
around the cast type selection.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_gro_receive() to pass up all types of packets that a L3 device
may receive.
1) For proper L2 packets received by the IQD sniffer, this is the
obvious thing to do.
2) For af_iucv (which doesn't provide a GRO assist), the GRO code will
transparently fall back to netif_receive_skb(). So there's no need to
special-case this traffic in our code.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
De-duplicate the pm callback implementations from the two sub-drivers,
replacing them with core helpers that delegate to the .set_online and
.set_offline callbacks.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply some cleanups to qeth_snmp_command() and its callback:
1. when accessing the user data, use the proper struct instead of
hard-coded offsets. Also copy the request data straight into the
allocated cmd, skipping the extra memdup_user() to a tmp buffer.
2. capping the request length is no longer needed, the same check gets
applied at a base level in qeth_alloc_cmd().
3. clean up some duplicated (and misindented) trace statements.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all cmds are dynamically allocated, the code for static cmd
buffers can go away entirely. Resulting in a nice reduction of
code/data size & complexity, while removing the risk that
qeth_clear_cmd_buffers() releases cmds that are still in-flight.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The base MPC cmds are the last remaining user of the static cmd buffers.
Port them over to use dynamic allocation, and stop backing the write
channel's cmd buffers with pages.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VNICC code is somewhat quirky in that it defers the whole cmd setup
to a common helper qeth_l2_vnicc_request(). Some of the cmd specifics
are then passed in via parameter, while others are simply hard-coded.
Split the whole machinery up into the usual format: one helper that
allocates the cmd & fills in the common fields, while all the cmd
originators take care of their sub-cmd type specific work.
This makes it much easier to calculate the cmd's precise length, and
reduces code complexity.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new wrapper that allocates DIAG cmds of the right size, and fills
in the common fields.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the adapter, assist and bridgeport cmd paths to
dynamic allocation. Most of the work is about re-organizing the cmd
headers, calculating the correct cmd length, and filling in the right
value in the sub-cmd's length field.
Since we now also set the correct length for cmds that are not reflected
by a fixed struct (ie SNMP), we can remove the work-around from
qeth_snmp_command().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For code that uses qeth_send_simple_setassparms_prot(), we currently
can't differentiate whether the cmd should contain (1) no parameter, or
(2) a 4-byte parameter with value 0.
At the moment this doesn't cause any trouble. But when using dynamically
allocated cmds, we need to know whether to allocate & transmit an
additional 4 bytes of zeroes.
So instead of the raw parameter value, pass a parameter pointer
(or NULL) to qeth_send_simple_setassparms_prot().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the usage of the write channel's static cmd buffers,
by dynamically allocating all simple IPA cmds (eg. STARTLAN, SETVMAC).
It also converts the OSN path.
Doing so requires some changes to how we calculate the cmd length.
Currently when building IPA cmds, we're quite generous in how much data
we send down to the device (basically the size of the biggest cmd we
know). This is no real concern at the moment, since the static cmd
buffers are backed with zeroed pages. But for dynamic allocations, the
exact length matters. So this patch also adds the needed length
calculations to each cmd path.
Commands that have multiple subtypes (eg. SETADP) of differing length
will be converted with follow-up patches.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are common steps when releasing an accepted or unaccepted socket.
Move this code into a common routine.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
