Switches work by learning the MAC address for each attached station by
monitoring traffic from each station. When a station sends a packet,
the switch records which port the MAC address is connected to.
With IPv4 networking, before communication commences with a neighbour,
an ARP packet is broadcasted to all stations asking for the MAC address
corresponding with the IPv4. The desired station responds with an ARP
reply, and the ARP reply causes the switch to learn which port the
station is connected to.
With IPv6 networking, the situation is rather different. Rather than
broadcasting ARP packets, a "neighbour solicitation" is multicasted
rather than broadcasted. This multicast needs to reach the intended
station in order for the neighbour to be discovered.
Once a neighbour has been discovered, and entered into the sending
stations neighbour cache, communication can restart at a point later
without sending a new neighbour solicitation, even if the entry in
the neighbour cache is marked as stale. This can be after the MAC
address has expired from the forwarding cache of the DSA switch -
when that occurs, there is a long pause in communication.
Our DSA implementation for mv88e6xxx switches disables flooding of
multicast and unicast frames for bridged ports. As per the above
description, this is fine for IPv4 networking, since the broadcasted
ARP queries will be sent to and received by all stations on the same
network. However, this breaks IPv6 very badly - blocking neighbour
solicitations and later causing connections to stall.
The defaults that the Linux bridge code expect from bridges are for
unknown unicast and unknown multicast frames to be flooded to all ports
on the bridge, which is at odds to the defaults adopted by our DSA
implementation for mv88e6xxx switches.
This commit enables by default flooding of both unknown unicast and
unknown multicast frames whenever a port is added to a bridge, and
disables the flooding when a port leaves the bridge. This means that
mv88e6xxx DSA switches now behave as per the bridge(8) man page, and
IPv6 works flawlessly through such a switch.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the bridge flags to Marvell 88e6xxx bridges, allowing
the multicast and unicast flood properties to be controlled. These
can be controlled on a per-port basis via commands such as:
bridge link set dev lan1 flood on|off
bridge link set dev lan1 mcast_flood on|off
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux bridge implementation allows various properties of the bridge
to be controlled, such as flooding unknown unicast and multicast frames.
This patch adds the necessary DSA infrastructure to allow the Linux
bridge support to control these properties for DSA switches.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[florian: Add missing dp and ds variables declaration to fix build]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xas_store() was interpreting the entry it found in the array as a node
entry if the bottom two bits had value 2. That's only true if either
the entry is in the root node or in a non-leaf node.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
The CFG/M/N/D registers are at an offset of 0x20 from the CMD register
only for blsp1_uart3 clock, so add it for uart3 only.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The RCG CFG/M/N/D register base could be at a different offset than
the CMD register, so introduce a cfg_offset to identify the offset
with respect to the CMD RCGR register.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
A copy of LTDC_PX and ETHCK_K (LTDC_K and ETHMAC_K) was introduced in
stm32mp1 dt-bindings file by mistake.
These bindings are not used and shouldn't be use to be conform with
convention name of the stm32mp1 clock IP.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix the bit width of the hse rtc divider because it's off by one.
Fixes: 2c87c9d331 ("clk: stm32mp1: add RTC clock")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The divisor of ethptp_k and ck_hse_rtc clocks is: 'value register
plus one'.
Then CLK_DIVIDER_ALLOW_ZERO flag has no effect and is useless here.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The divider of HSI (clk-hsi-div) is power of two divider.
Fixes: 9bee94e7b7 ("clk: stm32mp1: Introduce STM32MP1 clock driver")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
index 8: ck_mcu is divided by 256 (not 512)
Fixes: e51d297e9a ("clk: stm32mp1: add Sub System clocks")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
ck_csi is used for IO compensation so it should be
considered as "always-on" and kept on.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
STM32MP1 clock IP offers lots of Kernel clocks that are shared
by multiple IP's at the same time.
Then boot loader applies a clock tree that allows to use all IP's
at same time and with the maximum of performance.
Not change parents on a change rate on kernel clocks ensures
the integrity of the system.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes parent clock for axi, fdcan, sai and adc12 clocks.
Fixes: e51d297e9a ("clk: stm32mp1: add Sub System clocks")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
I noticed that modprobe clk-twl6040 can fail after a cold boot with:
abe_cm:clk:0010:0: failed to enable
...
Unhandled fault: imprecise external abort (0x1406) at 0xbe896b20
WARNING: CPU: 1 PID: 29 at drivers/clk/clk.c:828 clk_core_disable_lock+0x18/0x24
...
(clk_core_disable_lock) from [<c0123534>] (_disable_clocks+0x18/0x90)
(_disable_clocks) from [<c0124040>] (_idle+0x17c/0x244)
(_idle) from [<c0125ad4>] (omap_hwmod_idle+0x24/0x44)
(omap_hwmod_idle) from [<c053a038>] (sysc_runtime_suspend+0x48/0x108)
(sysc_runtime_suspend) from [<c06084c4>] (__rpm_callback+0x144/0x1d8)
(__rpm_callback) from [<c0608578>] (rpm_callback+0x20/0x80)
(rpm_callback) from [<c0607034>] (rpm_suspend+0x120/0x694)
(rpm_suspend) from [<c0607a78>] (__pm_runtime_idle+0x60/0x84)
(__pm_runtime_idle) from [<c053aaf0>] (sysc_probe+0x874/0xf2c)
(sysc_probe) from [<c05fecd4>] (platform_drv_probe+0x48/0x98)
After searching around for a similar issue, I came across an earlier fix
that never got merged upstream in the Android tree for glass-omap-xrr02.
There is patch "MFD: twl6040-codec: Implement PDMCLK cold temp errata"
by Misael Lopez Cruz <misael.lopez@ti.com>.
Based on my observations, this fix is also needed when cold booting
devices, and not just for deeper idle modes. Since we now have a clock
driver for pdmclk, let's fix the issue in twl6040_pdmclk_prepare().
Cc: Misael Lopez Cruz <misael.lopez@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
GSO packets with vnet_hdr must conform to a small set of gso_types.
The below commit uses flow dissection to drop packets that do not.
But it has false positives when the skb is not fully initialized.
Dissection needs skb->protocol and skb->network_header.
Infer skb->protocol from gso_type as the two must agree.
SKB_GSO_UDP can use both ipv4 and ipv6, so try both.
Exclude callers for which network header offset is not known.
Fixes: d5be7f632b ("net: validate untrusted gso packets without csum offload")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of gpio-gate-clk enables/disables the clock
using the GPIO in the ->enable() and ->disable() clock callbacks. This
requires the GPIO to be configurable in atomic contexts. While it is
the case for most memory-mapped GPIO controllers, it is not the case
for GPIO expanders on I2C or SPI.
This commit extends the gpio-gate-clk to check whether the GPIO calls
require sleeping or not. If sleeping is not required, the current
implementation based on ->enable()/->disable() is kept. However, if
sleeping is needed, we instead implement the logic in the ->prepare()
and ->unprepare() hooks. Thanks to this, a gate clock connected to a
GPIO on a GPIO expander can be controlled with the existing driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[sboyd@kernel.org: Mark clk ops static]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Tung Nguyen says:
====================
tipc: improvement for wait and wakeup
Some improvements for tipc_wait_for_xzy().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit replaces schedule_timeout() with wait_woken()
in function tipc_wait_for_rcvmsg(). wait_woken() uses
memory barriers in its implementation to avoid potential
race condition when putting a process into sleeping state
and then waking it up.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 844cf763fb ("tipc: make macro tipc_wait_for_cond() smp safe")
replaced finish_wait() with remove_wait_queue() but still used
prepare_to_wait(). This causes unnecessary conditional
checking before adding to wait queue in prepare_to_wait().
This commit replaces prepare_to_wait() with add_wait_queue()
as the pair function with remove_wait_queue().
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clk-rpmh driver only supports on and off RPMh clock resources. Let's
extend the driver by adding support for clocks that are managed by a
different type of RPMh resource known as Bus Clock Manager(BCM). The BCM
is a configurable shared resource aggregator that scales performance
based on a set of frequency points. The Qualcomm IP Accelerator (IPA)
clock is an example of a resource that is managed by the BCM and this a
requirement from the IPA driver in order to scale its core clock.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
These are in fact two clocks, they shouldn't be exposed as one. One is
required for accessing LCD controller registers (peripheral clock), while
other (AXI clock) can be optionally used as a pixel clock source for the
panel.
LCDC can alternatively use different clocks than the Display 1 AXI clock
for generating the pixel clock: the second AXI clock (fixed in this
commit too), the HDMI PLL, or the AXI bus clock.
They should really be controlled independently.
Link: https://lists.freedesktop.org/archives/dri-devel/2019-January/203975.html
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This case block has been terminated by a return, so not need
a switch fall-through
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull TI clock driver updates from Tero Kristo:
Contains the CLK_IS_BASIC flag cleanup, getting rid of the flag
completely from TI clock driver.
Also contains the autoidle clock support series from Andreas Kemnade,
which is needed for handling the hdq clocks properly during low power
states; at least on gta04 board.
* tag 'ti-clk-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
ARM: OMAP2+: hwmod: disable ick autoidling when a hwmod requires that
clk: ti: check clock type before doing autoidle ops
clk: ti: add a usecount for autoidle
clk: ti: generalize the init sequence of clk_hw_omap clocks
clk: ti: remove usage of CLK_IS_BASIC
clk: ti: add new API for checking if a provided clock is an OMAP clock
clk: ti: move clk_hw_omap list handling under generic part of the driver
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/clk/samsung/clk-s3c2443.c: In function ‘s3c2443_common_clk_init’:
drivers/clk/samsung/clk-s3c2443.c:390:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
samsung_clk_register_alias(ctx, s3c2450_aliases,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
ARRAY_SIZE(s3c2450_aliases));
~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/clk/samsung/clk-s3c2443.c:393:2: note: here
case S3C2416:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Platform driver driver_override field should not be initialized from
const memory because the core later kfree() it. If driver_override is
manually set later through sysfs, kfree() of old value leads to:
$ echo "new_value" > /sys/bus/platform/drivers/.../driver_override
kernel BUG at ../mm/slub.c:3960!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
...
(kfree) from [<c058e8c0>] (platform_set_driver_override+0x84/0xac)
(platform_set_driver_override) from [<c058e908>] (driver_override_store+0x20/0x34)
(driver_override_store) from [<c031f778>] (kernfs_fop_write+0x100/0x1dc)
(kernfs_fop_write) from [<c0296de8>] (__vfs_write+0x2c/0x17c)
(__vfs_write) from [<c02970c4>] (vfs_write+0xa4/0x188)
(vfs_write) from [<c02972e8>] (ksys_write+0x4c/0xac)
(ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
The clk-exynos5-subcmu driver uses override only for the purpose of
creating meaningful names for children devices (matching names of power
domains, e.g. DISP, MFC). The driver_override was not developed for
this purpose so just switch to default names of devices to fix the
issue.
Fixes: b06a532bf1 ("clk: samsung: Add Exynos5 sub-CMU clock driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
During initialization of subdevices if platform_device_alloc() failed,
returned NULL pointer will be later dereferenced. Add proper error
paths to exynos5_clk_register_subcmu(). The return value of this
function is still ignored because at this stage of init there is nothing
we can do.
Fixes: b06a532bf1 ("clk: samsung: Add Exynos5 sub-CMU clock driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This patch fixes a subtle PACKET_ORIGDEV regression which was a side
effect of fixes introduced by:
6a9e461f6f bonding: pass link-local packets to bonding master also.
... to:
b89f04c61e bonding: deliver link-local packets with skb->dev set to link that packets arrived on
While 6a9e461f6f restored pre-b89f04c61efe presence of link-local
packets on bonding masters (which is required e.g. by linux bridges
participating in spanning tree or needed for lab-like setups created
with group_fwd_mask) it also caused the originating device
information to be lost due to cloning.
Maciej Żenczykowski proposed another solution that doesn't require
packet cloning and retains original device information - instead of
returning RX_HANDLER_PASS for all link-local packets it's now limited
only to packets from inactive slaves.
At the same time, packets passed to bonding masters retain correct
information about the originating device and PACKET_ORIGDEV can be used
to determine it.
This elegantly solves all issues so far:
- link-local packets that were removed from bonding masters
- LLDP daemons being forced to explicitly bind to slave interfaces
- PACKET_ORIGDEV having no effect on bond interfaces
Fixes: 6a9e461f6f (bonding: pass link-local packets to bonding master also.)
Reported-by: Vincent Bernat <vincent@bernat.ch>
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error code isn't set on this path so it would result in returning
ERR_PTR(0) and a NULL dereference in the caller.
Fixes: 18d3eefb17 ("net: sched: refactor tcf_block_find() into standalone functions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similiar to commit e94cd8113c ("net: remove MTU limits for dummy and
ifb device"), MTU is irrelevant for VRF device. We init it as 64K while
limit it to [68, 1500] may make users feel confused.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warning by adding a missing break:
drivers/infiniband/hw/hfi1/tid_rdma.c: In function ‘hfi1_tid_rdma_wqe_interlock’:
drivers/infiniband/hw/hfi1/tid_rdma.c:3251:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (prev->wr.opcode) {
^~~~~~
drivers/infiniband/hw/hfi1/tid_rdma.c:3259:2: note: here
case IB_WR_RDMA_READ:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: c6c231175c ("IB/hfi1: Add interlock between TID RDMA WRITE and other requests")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kaike Wan <Kaike.wan@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Currently the only way to clear the forwarding cache was to delete the
entries one by one using the MRT_DEL_MFC socket option or to destroy and
recreate the socket.
Create a new socket option which with the use of optional flags can
clear any combination of multicast entries (static or not static) and
multicast vifs (static or not static).
Calling the new socket option MRT_FLUSH with the flags MRT_FLUSH_MFC and
MRT_FLUSH_VIFS will clear all entries and vifs on the socket except for
static entries.
Signed-off-by: Callum Sinclair <callum.sinclair@alliedtelesis.co.nz>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new function genphy_c45_check_and_restart_aneg() to reduce
boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used by config_aneg callback implementations of
PHY drivers and allows to reduce boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in genphy_config_aneg() for clause 22 PHY's, we should keep modes
from being advertised that are known to be broken with EEE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use this function in phy-c45.c too, therefore export it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit says:
====================
net: phy: improve genphy_read_status
Series includes two smaller improvements to genphy_read_status.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If link partner and we can't agree on any mode, then it doesn't make
sense to pretend we would have agreed on 10/half. Therefore set a
proper default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent changes to genphy_read_status() this orphaned register
read remained as leftover. So remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing ARM clock which will be used by cpufreq
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
[sboyd@kernel.org: Fixed numbering in dt header]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The arm pll bypass needs to propagate the rate upwards
in order for the cpufreq to work.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
