Some Marvell Alaska PHYs support 2.5G, 5G and 10G BaseT links. Their
default behaviour is to advertise all of these modes, but at the moment,
only 10GBaseT is supported. To prevent link partners from establishing
link at that speed, clear these modes upon configuring aneg parameters.
Fixes: 20b2af32ff ("net: phy: add Marvell Alaska X 88X3310 10Gigabit PHY support")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reported-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc fix from Michael Ellerman:
"One fix for an oops when using SRIOV, introduced by the recent changes
to support compound IOMMU groups.
Thanks to Alexey Kardashevskiy"
* tag 'powerpc-5.0-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/powernv/sriov: Register IOMMU groups for VFs
If a bulk layout recall or a metadata server reboot coincides with a
umount, then holding a reference to an inode is unsafe unless we
also hold a reference to the super block.
Fixes: fd9a8d7160 ("NFSv4.1: Fix bulk recall and destroy of layouts")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Pull SCSI fixes from James Bottomley:
"Four small fixes: three in drivers and one in the core.
The core fix is also minor in scope since the bug it fixes is only
known to affect systems using SCSI reservations. Of the driver bugs,
the libsas one is the most major because it can lead to multiple disks
on the same expander not being exposed"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: reset host byte in DID_NEXUS_FAILURE case
scsi: libsas: Fix rphy phy_identifier for PHYs with end devices attached
scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation
scsi: libiscsi: Fix race between iscsi_xmit_task and iscsi_complete_task
On some platforms such as HP Elite-x2-1013-g3, the platform BIOS
enforces XTAL to remain off before S0ix state can be achieved. This may
not be optimum when we want to enable use cases like Low Power Audio,
Wake on Voice etc which always need 24mhz clock.
This introduces a new quirk to allow S0ix entry when all other
conditions except for XTAL clock are good on a given platform. The extra
power consumed by XTAL clock is about 2mw but it saves much more
platform power compared to the system that remains in just PC10.
Link: https://bit.ly/2UmnrFf
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201579
Tested-by: "David E. Box" <david.e.box@linux.intel.com>
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
This patch introduces a new debugfs entry to read current Package
cstate residency counters. A similar variant of this patch was discussed
earlier "https://patchwork.kernel.org/patch/9908563/" but didn't make it
into mainline for various reasons. Current version only adds debugfs
entry which is quite useful for S0ix debug but excludes the exported API
that was there in initial version. Though there are tools like turbostat
and socwatch which can also show this info but sometimes its more
practical to have it here as it's hard to switch between various tools for
S0ix debug when pmc_core driver is the primary debug tool. Internal and
external customers have requested for this patch to be included in the
PMC driver on many occasions and Google Chrome OS team has already included
it in their builds. This becomes handy when requesting logs from external
customers who may not always have above mentioned tools in their integrated
kernel builds.
Package cstate residency MSRs provide useful debug information about
system idle states. In idle states system must enter deeper Package
cstates. Package cstates depend not only on Core cstates but also on
various IP block's power gating status and LTR values.
For Intel Core SoCs Package C10 entry is a must for deeper sleep states
such as S0ix. "Suspend-to-idle" should ideally take this path:
PC0 -> PC10 -> S0ix. For S0ix debug, its logical to check for
Package C10 residency first if for some reason system fails to enter S0ix.
Please refer to this link for MSR details:
https://software.intel.com/sites/default/files/managed/22/0d/335592-sdm-vol-4.pdf
Usage:
cat /sys/kernel/debug/pmc_core/package_cstate_show
Package C2 : 0xec2e21735f
Package C3 : 0xc30113ba4
Package C6 : 0x9ef4be15c5
Package C7 : 0x1e011904
Package C8 : 0x3c5653cfe5a
Package C9 : 0x0
Package C10 : 0x16fff4289
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: "David E. Box" <david.e.box@intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-and-tested-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The register (SLP_S0_RES) at offset slp_s0_offset is a 32 bit register.
The pmc_core_adjust_slp_s0_step() could overflow the u32 value while
returning it after adjusting the step. Thus change to u64, this is
already accounted for in debugfs attribute (that wants to output a
64 bit value).
Signed-off-by: Rajat Jain <rajatja@google.com>
Acked-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Commit 0252894f53 added the Legion Y530 to the no_hw_rfkill
list, but missed a Y530 variant using the nvidia 1060 graphics card.
I have had to blacklist ideapad-laptop as a result to get Wi-Fi working.
dmidecode info:
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: LENOVO
Product Name: 81LB
Version: Lenovo Legion Y530-15ICH-1060
Serial Number: <snip>
UUID: <snip>
Wake-up Type: Power Switch
SKU Number: LENOVO_MT_81LB_BU_idea_FM_Legion Y530-15ICH-1060
Family: Legion Y530-15ICH-1060
Signed-off-by: Mark Levedahl <mlevedahl@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Add support for capability register in order to distinct between the
systems with minor LED configuration differences. It reduces the amount
of code describing systems' LED configuration.
For example one system can be equipped with six LED, while the other
with only four. Reading this information from the capability registers
allows to use the same LED structure for such systems and set the
relevant configuration dynamically based on capability register
content.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
In the function wmi_dev_match() the variable id is dereferenced without
first performing a NULL check. The variable can for example be NULL if
a WMI driver is registered without specifying the id_table field in
struct wmi_driver.
Add a NULL check and return that the driver can't handle the device if
the variable is NULL.
Fixes: 844af950da ("platform/x86: wmi: Turn WMI into a bus driver")
Signed-off-by: Mattias Jacobsson <2pi@mok.nu>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
For some odd reason dell_rbu actually seems to want the physical and
not a bus address for the allocated buffer. Lets assume that actually
is correct given that it is BIOS-related and that is a good source
of insanity. In that case we should not use dma_alloc_coherent with
a NULL device to allocate memory, but use GFP_DMA32 to stay under
the 32-bit BIOS limit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Commit ae7c8cba32 ("platform/x86: ideapad-laptop: add lenovo RESCUER
R720-15IKBN to no_hw_rfkill_list") added
DMI_MATCH(DMI_BOARD_NAME, "80WW")
for Lenovo RESCUER R720-15IKBN.
But DMI_BOARD_NAME does not match 80WW on Lenovo RESCUER R720-15IKBN,
thus cause Wireless LAN still be hard blocked.
On Lenovo RESCUER R720-15IKBN:
~$ cat /sys/class/dmi/id/sys_vendor
LENOVO
~$ cat /sys/class/dmi/id/board_name
Provence-5R3
~$ cat /sys/class/dmi/id/product_name
80WW
~$ cat /sys/class/dmi/id/product_version
Lenovo R720-15IKBN
So on Lenovo RESCUER R720-15IKBN:
DMI_SYS_VENDOR should match "LENOVO",
DMI_BOARD_NAME should match "Provence-5R3",
DMI_PRODUCT_NAME should match "80WW",
DMI_PRODUCT_VERSION should match "Lenovo R720-15IKBN".
Fix it, and in according with other entries in no_hw_rfkill_list,
use DMI_PRODUCT_VERSION instead of DMI_BOARD_NAME.
Fixes: ae7c8cba32 ("platform/x86: ideapad-laptop: add lenovo RESCUER R720-15IKBN to no_hw_rfkill_list")
Signed-off-by: Yang Fan <nullptr.cpp@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
hid-asus depends on asus-wmi through the asus_wmi_evaluate_method. Before
this commit asus-wmi, and thus hid-asus, could not be loaded on non-Asus
systems. This breaks using Asus bluetooth keyboards such as the Asus
T100CHI keyboard with non Asus systems.
This commit fixes this by allowing asus-wmi to load on systems without the
Asus Management GUID.
This is safe to do since all asus-wmi sub drivers use
asus_wmi_register_driver which also checks for the GUID.
This commit also improves the error messages in asus_wmi_register_driver
to include "ASUS" in their description to make them more clear. This is
important since we now rely on those errors when loaded on systems without
the Asus Management GUID.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Use devm_hwmon_device_register_with_info() instead of
devm_hwmon_device_register_with_groups() to register the hwmon
device to simplify the code and make it easier to maintain.
As part of this change, thermal device registration is moved into
the hwmon core.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds optional regulator support to the pwm-fan driver. This is
necessary for pwm fans which are powered by a switchable supply.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This adds an optional regulator support (e.g. switchable supply) to the
pwm fan binding.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull clockevents updates from Daniel Lezcano:
- Update the binding documentation for the gpt timer (Anson Huang)
- Improve checking and error handling at init time on risc timer (Atish
Patra)
- Update the binding documentation for r8a774c0 cmt and tmu (Biju Das)
- Fail gracefully when clock rate is unavailable on sun5i (Chen-Yu Tsai)
- Rename the tango-xtal, pxa and cs5535 to timer-*.c for consistency
(Daniel Lezcano)
- Add the support for the tegra210 timer and add the platform's Kconfig
selection (Joseph Lo)
- Do a cleanup in the header inclusions and remove the unused ones for the
exynos_mct timer driver (Krzysztof Kozlowski)
- Remove some non-of dead code and fix the error path when initializing
the resources in the exynos_mct timer driver (Marek Szyprowski)
- Update the DT bindings for the MT7629 (Ryder Lee)
- Provide a workaround for the arm arch timer for Allwinner A64 timers
(Samuel Holland)
- Clear the timer interrupt at shutdown time on the exynos_mct timer
driver (Stuart Menefy)
Some stack pointers used to also be thread_info pointers
and were called tp. Now that they are only stack pointers,
rename them sp.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that current_thread_info is located at the beginning of 'current'
task struct, CURRENT_THREAD_INFO macro is not really needed any more.
This patch replaces it by loads of the value at PACA_THREAD_INFO(r13).
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Add PACA_THREAD_INFO rather than using PACACURRENT]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that thread_info is similar to task_struct, its address is in r2
so CURRENT_THREAD_INFO() macro is useless. This patch removes it.
This patch also moves the 'tovirt(r2, r2)' down just before the
reactivation of MMU translation, so that we keep the physical address
of 'current' in r2 until then. It avoids a few calls to tophys().
At the same time, as the 'cpu' field is not anymore in thread_info,
TI_CPU is renamed TASK_CPU by this patch.
It also allows to get rid of a couple of
'#ifdef CONFIG_VIRT_CPU_ACCOUNTING_NATIVE' as ACCOUNT_CPU_USER_ENTRY()
and ACCOUNT_CPU_USER_EXIT() are empty when
CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not defined.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Fix a missed conversion of TI_CPU idle_6xx.S]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The table of pointers 'current_set' has been used for retrieving
the stack and current. They used to be thread_info pointers as
they were pointing to the stack and current was taken from the
'task' field of the thread_info.
Now, the pointers of 'current_set' table are now both pointers
to task_struct and pointers to thread_info.
As they are used to get current, and the stack pointer is
retrieved from current's stack field, this patch changes
their type to task_struct, and renames secondary_ti to
secondary_current.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
thread_info is not anymore in the stack, so the entire stack
can now be used.
There is also no risk anymore of corrupting task_cpu(p) with a
stack overflow so the patch removes the test.
When doing this, an explicit test for NULL stack pointer is
needed in validate_sp() as it is not anymore implicitely covered
by the sizeof(thread_info) gap.
In the meantime, with the previous patch all pointers to the stacks
are not anymore pointers to thread_info so this patch changes them
to void*
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch activates CONFIG_THREAD_INFO_IN_TASK which
moves the thread_info into task_struct.
Moving thread_info into task_struct has the following advantages:
- It protects thread_info from corruption in the case of stack
overflows.
- Its address is harder to determine if stack addresses are leaked,
making a number of attacks more difficult.
This has the following consequences:
- thread_info is now located at the beginning of task_struct.
- The 'cpu' field is now in task_struct, and only exists when
CONFIG_SMP is active.
- thread_info doesn't have anymore the 'task' field.
This patch:
- Removes all recopy of thread_info struct when the stack changes.
- Changes the CURRENT_THREAD_INFO() macro to point to current.
- Selects CONFIG_THREAD_INFO_IN_TASK.
- Modifies raw_smp_processor_id() to get ->cpu from current without
including linux/sched.h to avoid circular inclusion and without
including asm/asm-offsets.h to avoid symbol names duplication
between ASM constants and C constants.
- Modifies klp_init_thread_info() to take a task_struct pointer
argument.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add task_stack.h to livepatch.h to fix build fails]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Make sure CURRENT_THREAD_INFO() is used with r1 which is the virtual
address of the stack, in order to ease the switch to r2 when we enable
THREAD_INFO_IN_TASK, as we have no register having the phys address of
current.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Change current_pt_regs() to use task_stack_page() rather than
current_thread_info() so that it keeps working once we enable
THREAD_INFO_IN_TASK.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Split out of large patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When we enable THREAD_INFO_IN_TASK we will remove our definition of
current_thread_info(). Instead it will come from linux/thread_info.h
So switch processor.h to include the latter, so that it can continue
to find current_thread_info().
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently INIT_SP_LIMIT uses sizeof(init_thread_info), but that symbol
won't exist when we enable THREAD_INFO_IN_TASK. So just use the sizeof
the type which is the same value but will continue to work.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rather than using the thread info use task_stack_page() to initialise
paca->kstack, that way it will work with THREAD_INFO_IN_TASK.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Update a few comments that talk about current_thread_info() in
preparation for THREAD_INFO_IN_TASK.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
We have a few places that use current_thread_info()->task to access
current. This won't work with THREAD_INFO_IN_TASK so fix them now.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A few places use CURRENT_THREAD_INFO, or the C version, to find the
stack. This will no longer work with THREAD_INFO_IN_TASK so change
them to find the stack in other ways.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The purpose of the pointer given to call_do_softirq() and
call_do_irq() is to point the new stack. Currently that's the same
thing as the thread_info, but won't be with THREAD_INFO_IN_TASK.
So change the parameter to void* and rename it 'sp'.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out of larger patch]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch renames THREAD_INFO to TASK_STACK, because it is in fact
the offset of the pointer to the stack in task_struct so this pointer
will not be impacted by the move of THREAD_INFO.
Also make it available on 64-bit, as we'll need it there when we
activate THREAD_INFO_IN_TASK.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Make available on 64-bit]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[text copied from commit 9bbd4c56b0
("arm64: prep stack walkers for THREAD_INFO_IN_TASK")]
When CONFIG_THREAD_INFO_IN_TASK is selected, task stacks may be freed
before a task is destroyed. To account for this, the stacks are
refcounted, and when manipulating the stack of another task, it is
necessary to get/put the stack to ensure it isn't freed and/or re-used
while we do so.
This patch reworks the powerpc stack walking code to account for this.
When CONFIG_THREAD_INFO_IN_TASK is not selected these perform no
refcounting, and this should only be a structural change that does not
affect behaviour.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Move try_get_task_stack() below tsk == NULL check in show_stack()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When moving to CONFIG_THREAD_INFO_IN_TASK, the thread_info 'cpu' field
gets moved into task_struct and only defined when CONFIG_SMP is set.
This patch ensures that TI_CPU is only used when CONFIG_SMP is set and
that task_struct 'cpu' field is not used directly out of SMP code.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When activating CONFIG_THREAD_INFO_IN_TASK, linux/sched.h includes
asm/current.h. This generates a circular dependency. To avoid that,
asm/processor.h shall not be included in mmu-hash.h.
In order to do that, this patch moves into a new header called
asm/task_size_64/32.h all the TASK_SIZE related constants, which can
then be included in mmu-hash.h directly.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Split out all the TASK_SIZE constants not just 64-bit ones]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Since only the virtual address of allocated blocks is used,
lets use functions returning directly virtual address.
Those functions have the advantage of also zeroing the block.
Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In __secondary_start() we load the thread_info of the idle task of the
secondary CPU from current_set[cpu], and then convert it into a stack
pointer before storing that back to paca->kstack.
As pointed out in commit f761622e59 ("powerpc: Initialise
paca->kstack before early_setup_secondary") it's important that we
initialise paca->kstack before calling the MMU setup code, in
particular slb_initialize(), because it will bolt the SLB entry for
the kstack into the SLB.
However we have already setup paca->kstack in cpu_idle_thread_init(),
since commit 3b5750644b ("[POWERPC] Bolt in SLB entry for kernel
stack on secondary cpus") (May 2008).
It's also in cpu_idle_thread_init() that we initialise current_set[cpu]
with the thread_info pointer, so there is no issue of the timing being
different between the two.
Therefore the initialisation of paca->kstack in __setup_secondary() is
completely redundant, so remove it.
This has the added benefit of removing code that runs in real mode,
and is therefore restricted by the RMO, and so opens the way for us to
enable THREAD_INFO_IN_TASK.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently in system_call_exit() we have an optimisation where we
disable MSR_RI (recoverable interrupt) and MSR_EE (external interrupt
enable) in a single mtmsrd instruction.
Unfortunately this will no longer work with THREAD_INFO_IN_TASK,
because then the load of TI_FLAGS might fault and faulting with MSR_RI
clear is treated as an unrecoverable exception which leads to a
panic().
So change the code to only clear MSR_EE prior to loading TI_FLAGS,
leaving the clear of MSR_RI until later. We have some latitude in
where do the clear of MSR_RI. A bit of experimentation has shown that
this location gives the least slow down.
This still causes a noticeable slow down in our null_syscall
performance. On a Power9 DD2.2:
Before After Delta Delta %
955 cycles 999 cycles -44 -4.6%
On the plus side this does simplify the code somewhat, because we
don't have to reenable MSR_RI on the restore_math() or
syscall_exit_work() paths which was necessitated previously by the
optimisation.
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Add support for the Tegra210 timer that runs at oscillator clock
(TMR10-TMR13). We need these timers to work as clock event device and to
replace the ARMv8 architected timer due to it can't survive across the
power cycle of the CPU core or CPUPORESET signal. So it can't be a wake-up
source when CPU suspends in power down state.
Also convert the original driver to use timer-of API.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
For the sake of consistency, let's rename the file to a name similar
to other file names in this directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
For the sake of consistency, let's rename the file to a name similar
to other file names in this directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
For the sake of consistency, let's rename the file to a name similar
to other file names in this directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
