Pull "mvebu dt64 for 4.9 (part 1)" from Gregory CLEMENT:
- add description for the new Armada 8040 dev board
- add the PIC and PMU on Armada 7K/8K
* tag 'mvebu-dt64-4.9-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: describe the PIC and PMU on Armada 7K/8K
arm64: dts: marvell: add description for the Armada 8040 dev board
arm64: dts: marvell: add description for the slave CP110 in Armada 8K
Pull "Qualcomm ARM64 Updates for v4.9" from Andy Gross:
* Updates for MSM8916 including TSCR, SMSM/SMP2P, and MBA reserve
* Update SCM node to denote being a reset-controller
* Fix broken interrupt settings
* Add TSENS nodes for MSM8916/MSM8996
* Add DB820c support
* Add MSM8916/APQ8016 display support
* tag 'qcom-arm64-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: apq8016-sbc: Add HDMI display support
arm64: dts: msm8916: Add display support
arm64: dts: db820c: add support to external sd card.
arm64: dts: db820c: add support to SPI on HS
arm64: dts: db820c: add support to LS-SPI0
arm64: dts: db820c: add support to I2C on HS
arm64: dts: db820c: add support to LS-I2C1
arm64: dts: db820c: add support to LS-I2C0
arm64: dts: db820c: add support to LS-UART0
arm64: dts: db820c: add basic board support
arm64: dts: msm8996: Add thermal zones, tsens and qfprom nodes
arm64: dts: msm8916: Add thermal zones, tsens and qfprom nodes
arm64: dts: qcom: Fix broken interrupt trigger settings
arm64: dts: qcom: msm8916: Add tcsr syscon
arm64: dts: qcom: msm8916: Make scm a reset-controller
arm64: dts: qcom: msm8916: Add mba memory reserve
arm64: dts: qcom: msm8916: Add smsm and smp2p nodes
Pull "ARM64: DT: Hisilicon SoC DT updates for 4.9" from Wei Xu:
- Set UART1 clock frequency to 150MHz for higher baud rates on hikey
- Add display subsystem, HDMI and cma nodes on hikey to support display
- Add syscon-reboot-mode support on hikey
- Add pstore support on hikey
- Add resets and sd-uhs-sdr property dwmmc ndoe on hikey
- Remove hip05_hns.dtsi since it can not be built without mbigenv1
- Update system controller bingding document for hip05 and hip06
- Add xge and sas support on hip06
* tag 'hisi-soc-dt-for-4.9' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi6220: add sd-uhs- properties into dwmmc_1
arm64: dts: hi6220: add resets property into dwmmc nodes
arm64: dts: hikey: extend default cma size to 128MB
arm64: dts: hip06: Append sas node
arm64: dts: hip06: Append hns node
dt-bindings: hisilicon: Add Hip05 and Hip06 system controller support
arm64: dts: hip05: kill hip05_hns.dtsi
arm64: dts: hikey: Add pstore support for HiKey
arm64: dts: hikey: Add hikey support for syscon-reboot-mode
arm64: dts: Add HDMI node for hi6220-hikey
arm64: dts: Add display subsystem DT nodes for hi6220-hikey
arm64: dts: set UART1 clock frequency to 150MHz
Pull "Samsung DeviceTree ARM64 update for v4.9" from Krzysztof Kozlowski:
1. Use human-friendly symbols for interrupt flags.
* tag 'samsung-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Use human-friendly symbols for timer interrupt flags
Merge "UniPhier ARM64 SoC DT updates for v4.9" from Masahiro Yamada:
* Match DT names other projects and documents
* Use clock/reset drivers
* Add new SoC/board support
* Misc
* tag 'uniphier-dt64-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: add LD11 SoC/Board support
arm64: dts: uniphier: add specific compatible to SoC-Glue node
arm64: dts: uniphier: use clock/reset controllers
arm64: dts: uniphier: add pinctrl property to System Bus node
arm64: dts: uniphier: match DT names to other projects and documents
This commit adds a reference to the appropriate MSI controller in the
description of the PCIe controllers on Marvel Armada 7K and 8K
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Paul Mackerras writes:
The highlights are:
* Reduced latency for interrupts from PCI pass-through devices, from
Suresh Warrier and me.
* Halt-polling implementation from Suraj Jitindar Singh.
* 64-bit VCPU statistics, also from Suraj.
* Various other minor fixes and improvements.
The AES-CTR glue code avoids calling into the blkcipher API for the
tail portion of the walk, by comparing the remainder of walk.nbytes
modulo AES_BLOCK_SIZE with the residual nbytes, and jumping straight
into the tail processing block if they are equal. This tail processing
block checks whether nbytes != 0, and does nothing otherwise.
However, in case of an allocation failure in the blkcipher layer, we
may enter this code with walk.nbytes == 0, while nbytes > 0. In this
case, we should not dereference the source and destination pointers,
since they may be NULL. So instead of checking for nbytes != 0, check
for (walk.nbytes % AES_BLOCK_SIZE) != 0, which implies the former in
non-error conditions.
Fixes: 49788fe2a1 ("arm64/crypto: AES-ECB/CBC/CTR/XTS using ARMv8 NEON and Crypto Extensions")
Cc: stable@vger.kernel.org
Reported-by: xiakaixu <xiakaixu@huawei.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when running on FVP, CPU 0 boots up with its BPR changed from
the reset value. This renders it impossible to (preemptively) prioritize
interrupts on CPU 0.
This is harmless on normal systems since Linux typically does not
support preemptive interrupts. It does however cause problems in
systems with additional changes (such as patches for NMI simulation).
Many thanks to Andrew Thoelke for suggesting the BPR as having the
potential to harm preemption.
Suggested-by: Andrew Thoelke <andrew.thoelke@arm.com>
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Make use of the new alternative_if and alternative_else_nop_endif and
get rid of our open-coded NOP sleds, making the code simpler to read.
Note that for __kvm_call_hyp the branch to __vhe_hyp_call has been moved
out of the alternative sequence, and in the default case there will be
four additional NOPs executed.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: kvmarm@lists.cs.columbia.edu
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Make use of the new alternative_if and alternative_else_nop_endif and
get rid of our homebew NOP sleds, making the code simpler to read.
Note that for cpu_do_switch_mm the ret has been moved out of the
alternative sequence, and in the default case there will be three
additional NOPs executed.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In some cases, one side of an alternative sequence is simply a number of
NOPs used to balance the other side. Keeping track of this manually is
tedious, and the presence of large chains of NOPs makes the code more
painful to read than necessary.
To ameliorate matters, this patch adds a new alternative_else_nop_endif,
which automatically balances an alternative sequence with a trivial NOP
sled.
In many cases, we would like a NOP-sled in the default case, and
instructions patched in in the presence of a feature. To enable the NOPs
to be generated automatically for this case, this patch also adds a new
alternative_if, and updates alternative_else and alternative_endif to
work with either alternative_if or alternative_endif.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Martin <dave.martin@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: use new nops macro to generate nop sequences]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The LSE atomics are implemented using alternative code sequences of
different lengths, and explicit NOP padding is used to ensure the
patching works correctly.
This patch converts the bulk of the LSE code over to using the __nops
macro, which makes it slightly clearer as to what is going on and also
consolidates all of the padding at the end of the various sequences.
Signed-off-by: Will Deacon <will.deacon@arm.com>
NOP sequences tend to get used for padding out alternative sections
and uarch-specific pipeline flushes in errata workarounds.
This patch adds macros for generating these sequences as both inline
asm blocks, but also as strings suitable for embedding in other asm
blocks directly.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Similar to our {read,write}_sysreg accessors for architected, named
system registers, this patch introduces {read,write}_sysreg_s variants
that can take arbitrary sys_reg output and therefore access IMPDEF
registers or registers that unsupported by binutils.
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We've grown our own versions of bug.h, ftrace.h, pci.h and topology.h,
so generating the generic ones as well is unnecessary and a potential
source of build hiccups. At the very least, having them present has
confused my source-indexing tool, and that simply will not do.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Systems with differing CPU i-cache/d-cache line sizes can cause
problems with the cache management by software when the execution
is migrated from one to another. Usually, the application reads
the cache size on a CPU and then uses that length to perform cache
operations. However, if it gets migrated to another CPU with a smaller
cache line size, things could go completely wrong. To prevent such
cases, always use the smallest cache line size among the CPUs. The
kernel CPU feature infrastructure already keeps track of the safe
value for all CPUID registers including CTR. This patch works around
the problem by :
For kernel, dynamically patch the kernel to read the cache size
from the system wide copy of CTR_EL0.
For applications, trap read accesses to CTR_EL0 (by clearing the SCTLR.UCT)
and emulate the mrs instruction to return the system wide safe value
of CTR_EL0.
For faster access (i.e, avoiding to lookup the system wide value of CTR_EL0
via read_system_reg), we keep track of the pointer to table entry for
CTR_EL0 in the CPU feature infrastructure.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Right now we trap some of the user space data cache operations
based on a few Errata (ARM 819472, 826319, 827319 and 824069).
We need to trap userspace access to CTR_EL0, if we detect mismatched
cache line size. Since both these traps share the EC, refactor
the handler a little bit to make it a bit more reader friendly.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On systems with mismatched i/d cache min line sizes, we need to use
the smallest size possible across all CPUs. This will be done by fetching
the system wide safe value from CPU feature infrastructure.
However the some special users(e.g kexec, hibernate) would need the line
size on the CPU (rather than the system wide), when either the system
wide feature may not be accessible or it is guranteed that the caller
executes with a gurantee of no migration.
Provide another helper which will fetch cache line size on the current CPU.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: James Morse <james.morse@arm.com>
Reviewed-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
adrp uses PC-relative address offset to a page (of 4K size) of
a symbol. If it appears in an alternative code patched in, we
should adjust the offset to reflect the address where it will
be run from. This patch adds support for fixing the offset
for adrp instructions.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The alternative code patching doesn't check if the replaced instruction
uses a pc relative literal. This could cause silent corruption in the
instruction stream as the instruction will be executed from a different
address than what it was compiled for. Catch all such cases.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Suggested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Right now we run through the work around checks on a CPU
from __cpuinfo_store_cpu. There are some problems with that:
1) We initialise the system wide CPU feature registers only after the
Boot CPU updates its cpuinfo. Now, if a work around depends on the
variance of a CPU ID feature (e.g, check for Cache Line size mismatch),
we have no way of performing it cleanly for the boot CPU.
2) It is out of place, invoked from __cpuinfo_store_cpu() in cpuinfo.c. It
is not an obvious place for that.
This patch rearranges the CPU specific capability(aka work around) checks.
1) At the moment we use verify_local_cpu_capabilities() to check if a new
CPU has all the system advertised features. Use this for the secondary CPUs
to perform the work around check. For that we rename
verify_local_cpu_capabilities() => check_local_cpu_capabilities()
which:
If the system wide capabilities haven't been initialised (i.e, the CPU
is activated at the boot), update the system wide detected work arounds.
Otherwise (i.e a CPU hotplugged in later) verify that this CPU conforms to the
system wide capabilities.
2) Boot CPU updates the work arounds from smp_prepare_boot_cpu() after we have
initialised the system wide CPU feature values.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This is a cosmetic change to rename the functions dealing with
the errata work arounds to be more consistent with their naming.
1) check_local_cpu_errata() => update_cpu_errata_workarounds()
check_local_cpu_errata() actually updates the system's errata work
arounds. So rename it to reflect the same.
2) verify_local_cpu_errata() => verify_local_cpu_errata_workarounds()
Use errata_workarounds instead of _errata.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Right now we use 0 as the safe value for CTR_EL0:L1Ip, which is
not defined at the moment. The safer value for the L1Ip should be
the weakest of the policies, which happens to be AIVIVT. While at it,
fix the comment about safe_val.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
1. Remove the old binding code.
2. Read the nid of cpu0 from dts.
3. Fallback the nid of cpu0 to 0 when numa=off is set in bootargs.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When the deleted code is executed, only the bit of cpu0 was set on
cpu_possible_mask. So that, only set_cpu_numa_node(0, NUMA_NO_NODE); will
be executed. And map_cpu_to_node(0, 0) will soon be called. So these code
can be safely removed.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
To make each percpu area allocated from its local numa node. Without this
patch, all percpu areas will be allocated from the node which cpu0 belongs
to.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Use pr_fmt to prefix kernel output, and remove duplicated msg
of NUMA turned off.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
numa_init may return error because of numa configuration error. So "No
NUMA configuration found" is inaccurate. In fact, specific configuration
error information should be immediately printed by the testing branch.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
By using a common attr_groups array, the common arm_pmu code can set up
common files (e.g. cpumask) for us in subsequent patches.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
When debug preempt or preempt tracer is enabled, preempt_count_add/sub()
can be traced by function and function graph tracing, and
preempt_disable/enable() would call preempt_count_add/sub(), so in Ftrace
subsystem we should use preempt_disable/enable_notrace instead.
In the commit 345ddcc882 ("ftrace: Have set_ftrace_pid use the bitmap
like events do") the function this_cpu_read() was added to
trace_graph_entry(), and if this_cpu_read() calls preempt_disable(), graph
tracer will go into a recursive loop, even if the tracing_on is
disabled.
So this patch change to use preempt_enable/disable_notrace instead in
this_cpu_read().
Since Yonghui Yang helped a lot to find the root cause of this problem,
so also add his SOB.
Signed-off-by: Yonghui Yang <mark.yang@spreadtrum.com>
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
smp_mb__before_spinlock() is intended to upgrade a spin_lock() operation
to a full barrier, such that prior stores are ordered with respect to
loads and stores occuring inside the critical section.
Unfortunately, the core code defines the barrier as smp_wmb(), which
is insufficient to provide the required ordering guarantees when used in
conjunction with our load-acquire-based spinlock implementation.
This patch overrides the arm64 definition of smp_mb__before_spinlock()
to map to a full smp_mb().
Cc: <stable@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When CONFIG_PID_IN_CONTEXTIDR is not selected, we use an empty stub
definition of contextidr_thread_switch(). As everything we rely upon
exists regardless of CONFIG_PID_IN_CONTEXTIDR, we don't strictly require
an empty stub.
By using IS_ENABLED() rather than ifdeffery, we avoid duplication, and
get compiler coverage on all the code even when CONFIG_PID_IN_CONTEXTIDR
is not selected and the code is optimised away.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.
This patch makes use of these across arm64 to make code shorter and
clearer. For sequences with a trailing ISB, the existing isb() macro is
also used so that asm blocks can be removed entirely.
A few uses of inline assembly for msr/mrs are left as-is. Those
manipulating sp_el0 for the current thread_info value have special
clobber requiremends.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.
This patch makes use of these in the arm64 KVM code to make the code
shorter and clearer.
At the same time, a comment style violation next to a system register
access is fixed up in reset_pmcr, and comments describing whether
operations are reads or writes are removed as this is now painfully
obvious.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.
This patch makes use of these in the arm64 DCC accessors to make the
code shorter and clearer.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
A while back we added {read,write}_sysreg accessors to handle accesses
to system registers, without the usual boilerplate asm volatile,
temporary variable, etc.
This patch makes use of these in the arm64 arch timer accessors to make
the code shorter and clearer.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently write_sysreg has to allocate a temporary register to write
zero to a system register, which is unfortunate given that the MSR
instruction accepts XZR as an operand.
Allow XZR to be used when appropriate by fiddling with the assembly
constraints.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The 'dma-coherent' indicates that the hardware IP block can ensure
the coherency of the data transferred from/to the IP block. This
can avoid the software cache flush/invalid actions, and improve
the performance significantly.
The PCI IP block of ls2080a has this capability, so adding this
feature to improve the PCI performance.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
KVM: s390: features and fixes for 4.9
- lazy enablement of runtime instrumentation
- up to 255 CPUs for nested guests
- rework of machine check deliver
- cleanups/fixes
If, when proxying a GICV access at EL2, we detect that the guest is
doing something silly, report an EL1 SError instead ofgnoring the
access.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
If EL1 generates an asynchronous abort and then traps into EL2
before the abort has been delivered, we may end-up with the
abort firing at the worse possible place: on the host.
In order to avoid this, it is necessary to take the abort at EL2,
by clearing the PSTATE.A bit. In order to survive this abort,
we do it at a point where we're in a known state with respect
to the world switch, and handle the resulting exception,
overloading the exit code in the process.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
If we have caught an SError whilst exiting, we've tagged the
exit code with the pending information. In that case, let's
re-inject the error into the guest, after having adjusted
the PC if required.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Similarily to EL1, an asynchronous abort can be triggered whilst
running at EL2. But instead of making that a new error code,
we need to communicate it to the rest of KVM together with
the exit reason. So let's hijack a single bit that allows the
exception code to be tagged with a "pending SError" information.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
As we now have some basic handling to EL1-triggered aborts, we can
actually report them to KVM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
If we've exited the guest because it has triggered an asynchronous
abort from EL1, a possible course of action is to let it know it
screwed up by giving it a Virtual Abort to chew on.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
