Move the PMU name into a common header file so it may
be referenced by other users.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARMv8 machines can identify the micro/arch defined counters
that are available on a machine. Add all these counters to the
default armv8 perf map. At run-time disable the counters which
are not available on the given PMU.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
In preparation for ACPI support, add a pmu_probe_info table to
the arm_pmu_device_probe() call. This table gets used when
probing in the absence of a devicetree node for PMU.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
With our DMA ops enabled for PCI devices, we should avoid allocating
IOVAs which a host bridge might misinterpret as peer-to-peer DMA and
lead to faults, corruption or other badness. To be safe, punch out holes
for all of the relevant host bridge's windows when initialising a DMA
domain for a PCI device.
CC: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Inki Dae <inki.dae@samsung.com>
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch introduces ARCH_ZX to add the support of the ZTE ZX SoC
family for the arm64 architecture.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree support for ZX296718 SoC and evaluation board based
on it. Also document new values.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable both gxbb USB controller and add a 5V regulator for the OTG port
VBUS
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[khilman: rename vbus node to match P200 schematics]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Kprobes searches backwards a finite number of instructions to determine if
there is an attempt to probe a load/store exclusive sequence. It stops when
it hits the maximum number of instructions or a load or store exclusive.
However this means it can run up past the beginning of the function and
start looking at literal constants. This has been shown to cause a false
positive and blocks insertion of the probe. To fix this, further limit the
backwards search to stop if it hits a symbol address from kallsyms. The
presumption is that this is the entry point to this code (particularly for
the common case of placing probes at the beginning of functions).
This also improves efficiency by not searching code that is not part of the
function. There may be some possibility that the label might not denote the
entry path to the probed instruction but the likelihood seems low and this
is just another example of how the kprobes user really needs to be
careful about what they are doing.
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: David A. Long <dave.long@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull "Allwinner ARM64 Kconfig changes" from Maxime Ripard:
Select the pinctrl driver in kconfig
* tag 'sunxi-config64-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
arm64: sunxi: Kconfig: add essential pinctrl driver
Pull "Broadcom soc-arm64 changes for 4.9" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoC changes for 4.9, please pull
the following:
- collective effort from Florian, Doug and Markus to add the ARCH_BRCMSTB Kconfig
symbol to the ARM64 kernel build, which is purposedly the same as the ARM/Linux
one in order not to update any driver dependencies
* tag 'arm-soc/for-4.9/soc-arm64' of http://github.com/Broadcom/stblinux:
arm64: Add Broadcom Set Top Box Kconfig entry point
Pull "Renesas ARM64 Based SoC Defconfig Updates for v4.9" from Simon Horman:
* Enable HSUSB and SDHI
* tag 'renesas-arm64-defconfig-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: defconfig: Enable SDHI and GPIO_REGULATOR
arm64: defconfig: Add Renesas R-Car HSUSB driver support as module
Enable common modules for power management; one is to enable
CPUFREQ_DT driver; the driver is used by many platforms by passing OPP
table from device tree.
Also enables thermal related drivers. Firstly we need enable
configuration CPU_THERMAL for CPU cooling device driver, this will bind
thermal zone with CPU cooling device; and enable 'power allocator'
thermal governor.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "mvebu defconfig64 for 4.9 (part 1)" from Gregory CLEMENT:
- add PCIe driver for Aardvark for Armada 3700
- enable xhci-platform for A7K/A8K
* tag 'mvebu-defconfig64-4.9-1' of git://git.infradead.org/linux-mvebu:
arm64: configs: enable PCIe driver for Aardvark
arm64: defconfig: enable xhci-platform
Pull "Qualcomm ARM64 Based defconfig Updates for v4.9" from Andy Gross:
* Enable defconfig options for QDF2432
* tag 'qcom-arm64-defconfig-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: defconfig: Enable QDF2432 config options
drivers/char/hw_random/Kconfig has 'default m', so
simply removing this entry from the defconfig will
enable building HW random drivers as modules.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "ARM64: hisilicon: defconfig updates for 4.9" from Wei Xu:
- Enable hisilicon SAS and XGE for hip05 and hip06
- Enable drm, powerkey, bluetooth and adv7511/adv7533 for hikey
- Add PINCTRL to HISI platform
* tag 'hisi-defconfig-for-4.9' of git://github.com/hisilicon/linux-hisi:
Kconfig: ARCH_HISI: Add PINCTRL to HISI platform
arm64: defconfig: enable bluetooth supports as modules
arm64: defconfig: enable CONFIG_INPUT_HISI_POWERKEY for HiKey
arm64: defconfig: Enable HiSilicon kirin drm, adv7533 for HiKey
arm64: defconfig: Enable Hisi SAS and HNS
* dt/irq-fix:
arm64: dts: Fix broken architected timer interrupt trigger
This resolves a non-obvious conflict between a bugfix from
v4.8 and a cleanup for the exynos7 platform.
The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).
A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.
The respective maintainers are of course welcome to prove me wrong.
While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).
Acked-by: Duc Dang <dhdang@apm.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the nodes for the dwc2 USB controller and the related USB PHYs.
Currently we force usb0 to host mode because OTG is currently not
working in our PHY driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add nodes for i2c bus on gxbb based platforms.
On the OdroidC2 (I2C A) and P200 (I2C B), the pull-up resistor are
present directly on the board. This indicates that these pins are
dedicated to i2c.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic reference driver uses the "mc_val" devicetree property to
configure the PRG_ETHERNET_ADDR0 register. Unfortunately it uses magic
values for this configuration.
According to the datasheet the PRG_ETHERNET_ADDR0 register is at address
0xc8834108. However, the reference driver uses 0xc8834540 instead.
According to my tests, the value from the reference driver is correct.
No changes are required to the board dts files because the only
required configuration option is the phy-mode, which had to be
configured correctly before as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Pull "arm64: Xilinx ZynqMP dt patches for v4.9" from Michal Simek:
- Fix gic ranges property
- Use 64bit size cells format
- Add PCIe node
- Correct pmu and watchdog nodes
* tag 'zynqmp-dt-for-4.9' of https://github.com/Xilinx/linux-xlnx:
ARM64: zynqmp: Correct the watchdog timer interrupt number
ARM64: zynqmp: Add missing interrupt-parent to PMU node
ARM64: zynqmp: Add PCIe node
ARM64: zynqmp: Use 64bit size cell format
ARM64: zynqmp: Align gic ranges for 64k in device tree
Pull "ARM: mediatek: dts64 updates for v4.9" from Matthias Brugger:
- add HDMI related nodes to mt8173
- enable the HDMI output on mt8173-evb
* tag 'v4.8-next-dts64' of https://github.com/mbgg/linux-mediatek:
arm64: dts: mt8173-evb: enable HDMI output
arm64: dts: mt8173: Add HDMI related nodes
Pull "i.MX arm64 device tree changes for 4.9" from Shawn Guo:
- Add property dma-coherent for ls2080a PCI device to save software
cache maintenance.
- Update serial aliases and use stdout-path to sepecify console for
ls2080a and ls1043a boards.
- Add DDR memory controller device node for ls2080a and ls1043a SoCs.
* tag 'imx-dt64-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls2080a: Add 'dma-coherent' for ls2080a PCI nodes
arm64: dts: add stdout-path to chosen node for ls2080a/ls1043a boards
arm64: dts: updates serial aliases for ls1043a rdb and qds boards
arm64: dts: Add DDR memory controller for Layerscape SoCs
Pull "arm64: tegra: Device tree changes for v4.9-rc1" from Thierry Reding:
Add a couple of devices (AGIC, ADMA) on Tegra210 and enable them on
Smaug. Also enable DPAUX on Smaug to allow the I2C bus that shares pads
with the DPAUX to be used to access various audio devices. Furthermore,
enable the XUSB controller on Smaug for USB 3.0 support.
Finally, select PM_GENERIC_DOMAINS for 64-bit Tegra devices to make sure
devices are probed only after their power partitions have been enabled.
* tag 'tegra-for-4.9-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Select PM_GENERIC_DOMAINS
arm64: tegra: Enable XUSB controller on Tegra210 Smaug
arm64: tegra: Add the various audio devices for Tegra210 Smaug
arm64: tegra: Enable DPAUX for Tegra210 Smaug
arm64: tegra: Add ACONNECT, ADMA and AGIC nodes Tegra210 Smaug
arm64: tegra: Add SOR power-domain for Tegra210
arm64: tegra: Add ADMA node for Tegra210
arm64: tegra: Add AGIC node for Tegra210
arm64: tegra: Drop clock and reset names for XUSB powergates
arm64: tegra: Simplify Tegra210 GPIO compatible value
Pull "Rockchip dts64 changes for 4.9" from Heiko Stübner:
64bit Rockchip devicetree changes containing support for the recently
added firmware reboot-flag support, one new board the Tronsmart Orion
based on the rk3368 and a large number of newly supported peripherals
for the rk3399 (type-c phy, usb2 phy, pcie controller and pcie phy,
gmac, arm-pmu using ppi partitioning, efuse, saradc) as well as some
smaller housekeeping and non-critical fixes.
* tag 'v4.9-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (22 commits)
arm64: dts: rockchip: add Type-C phy for RK3399
arm64: dts: rockchip: enable the gmac for rk3399 evb board
arm64: dts: rockchip: add the gmac needed node for rk3399
arm64: dts: rockchip: support the pmu node for rk3399
arm64: dts: rockchip: change all interrupts cells to 4 on rk3399 SoCs
arm64: dts: rockchip: add the tcpc for rk3399 power domain
arm64: dts: rockchip: add efuse0 device node for rk3399
arm64: dts: rockchip: configure PCIe support for rk3399-evb
arm64: dts: rockchip: add the PCIe controller support for RK3399
arm64: dts: rockchip: add the PCIe PHY for RK3399
arm64: dts: rockchip: add the gmac power domain on rk3399
arm64: dts: rockchip: Add pinctrl entry for 32k clock on rk3399
arm64: dts: rockchip: set to CCI clock of RK3399 to 600M
arm64: dts: rockchip: fix the address map for WDT0 and WDT1
arm64: dts: rockchip: add the saradc for rk3399
arm64: dts: rockchip: configure usb2-phy support for rk3399-evb
arm64: dts: rockchip: add usb2-phy support for rk3399
arm64: dts: rockchip: add syscon-reboot-mode DT node
soc: rockchip: add reboot-mode header
arm64: dts: rockchip: remove broken-cd from sdio0
...
Pull "Broadcom devicetree-arm64 changes for 4.9" from Florian Fainelli:
This pull request contains Broadcom ARM64-based SoC Device Tree changes for
v4.9, please pull the folllowing:
- Dhanajay adds the PWM Device Tree nodes to the Northstar 2 DTS files
* tag 'arm-soc/for-4.9/devicetree-arm64' of http://github.com/Broadcom/stblinux:
arm64: dts: Add PWM DT node for NS2
