The cros_ec_dev module is responsible for registering the MFD devices
attached to the ChromeOS EC. This patch moves this module to drivers/mfd
so calls to mfd_add_devices() are not done from outside the MFD subtree
anymore.
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 8275b77a15 ("mfd: rts5249: Add support for RTS5250S power
saving") adds powersaving support for device-ids 5249 524a and 525a.
But as a side effect it breaks ASPM support for all the other device-ids,
causing e.g. the Haswell CPU on a Lenovo T440s to not go into a higher
c-state then PC3, while previously it would go to PC7, causing the
machine to idle at 7.4W instead of 6.6W!
The problem here is the new option.dev_aspm_mode field, which only gets
explicitly initialized in the new code for the device-ids 5249 524a and
525a. Leaving the dev_aspm_mode 0 for the other device-ids.
The default dev_aspm_mode 0 is mapped to DEV_ASPM_DISABLE, but the
old behavior of calling rtsx_pci_enable_aspm() when idle and
rtsx_pci_disable_aspm() when busy happens when dev_aspm_mode ==
DEV_ASPM_DYNAMIC.
This commit changes the enum so that 0 = DEV_ASPM_DYNAMIC matching the
old default behavior, fixing the pm regression with the other device-ids.
Fixes: 8275b77a15 ("mfd: rts5249: Add support for RTS5250S power saving")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rui Feng <rui_feng@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Because Realtek card reader drivers are pcie and usb drivers,
and they bridge mmc subsystem and memstick subsystem, they are
not mfd drivers. Greg and Lee Jones had a discussion about
where to put the drivers, the result is that misc is a good
place for them, so I move all files to misc. If I don't move
them to a right place, I can't add any patch for this driver.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Perry Yuan <perry_yuan@dell.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull sound updates from Takashi Iwai:
"There are no big surprising changes in this cycle, yet not too boring,
either. The biggest change from diffstat POV is the removal of the
legacy OSS driver codes that have been already disabled for a long
time. This will bring a few trivial merge conflicts.
As new features in ASoC side, there are two things: a new AC97 bus
implementation and AMD Stony platform support. Both include the
relevant changes shared with other subsystems, e.g. AC97 MFD changes
and DRM AMD changes.
Some other highlighted topics are:
- A bunch of USB-audio drivers got the hardening against the
malicious device accesses with a new helper code for endpoint
sanity check
- Lots of cleanups for ASoC Intel platform code, including support
for their open source audio firmware
- Continued ASoC core componentization works
- Support for scaling MCLK with sample rate in ASoC simple-card
- Stabler PCM hot-unplug capability, especially for ASoC usages"
* tag 'sound-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (302 commits)
Documentation: sound: hd-audio: notes.rst
ASoC: bcm2835: Support left/right justified and DSP modes
ASoC: bcm2835: Enforce full symmetry
ASoC: bcm2835: Support additional samplerates up to 384kHz
ASoC: bcm2835: Add support for TDM modes
ASoC: add mclk-fs support to audio graph card
ASoC: add mclk-fs to audio graph card binding
ASoC: rt5514: work around link error
ASoC: rt5514: mark PM functions as __maybe_unused
ASoC: rt5663: Check the JD status in the button pushing
ASoC: amd: Modified DMA transfer Mechanism for Playback
ASoC: rt5645: Wait for 400msec before concluding on value of RT5645_VENDOR_ID2
ASoC: sun4i-codec: fixed 32bit audio capture support for H3/H2+
ASoC: da7213: add support for DSP modes
ASoC: sun8i-codec: Add a comment on the LRCK inversion
ASoC: sun8i-codec: Set the BCLK divider
ASoC: rt5663: Delay and retry reading rt5663 ID register
ASoC: amd: use do_div rather than 64 bit division to fix 32 bit builds
ASoC: cs42l56: Fix reset GPIO name in example DT binding
ASoC: rt5514-spi: check irq status to schedule data copy in resume function
...
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups"
* tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (91 commits)
sdhci-fujitsu: add support for setting the CMD_DAT_DELAY attribute
dt-bindings: sdhci-fujitsu: document cmd-dat-delay property
mmc: tmio: Replace msleep() of 20ms or less with usleep_range()
mmc: dw_mmc: Convert timers to use timer_setup()
mmc: dw_mmc: Cleanup the DTO timer like the CTO one
mmc: vub300: Use common code in __download_offload_pseudocode()
mmc: tmio: Use common error handling code in tmio_mmc_host_probe()
mmc: Convert timers to use timer_setup()
mmc: sdhci-acpi: Fix voltage switch for some Intel host controllers
mmc: sdhci-acpi: Let devices define their own private data
mmc: mediatek: perfer to use rise edge latching for cmd line
mmc: mediatek: improve eMMC hs400 mode read performance
mmc: mediatek: add latch-ck support
mmc: mediatek: add support of source_cg clock
mmc: mediatek: add stop_clk fix and enhance_rx support
mmc: mediatek: add busy_check support
mmc: mediatek: add async fifo and data tune support
mmc: mediatek: add pad_tune0 support
mmc: mediatek: make hs400_tune_response only for mt8173
arm64: dts: mt8173: remove "mediatek, mt8135-mmc" from mmc nodes
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On gen3 PCI-Express we should send command one by one.
If sending many commands in one packet will lead to a failure.
Signed-off-by: rui_feng <rui_feng@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SmartDock uses ADC_RESERVED_ACC_3 (0x10) ADC ID type and provides following
features:
1. USB host with embedded USB hub (2-4 ports) for mice, keyboard, etc,
2. MHL for video output,
3. charging.
Tested with Unitek Y-2165 MHL+OTG Hub Smart Phone Dock.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Enabling power on VBUS micro-usb pin is required only when passive OTG
cable is connected. Initially OTG VBUS power control was planned to be
done in charger driver. However such information is not really available
from the extcon notifications, so VBUS power control has to be done
directly in MUIC driver, which has all information about the attached
accessory.
For example SmartDock is externally powered accessory, provides OTG
(USB HOST) functionality and use VBUS pin for charging a device battery,
so the VBUS charging pump should be disabled in such case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The extcon has two type of extcon devices as following.
- 'extcon provider deivce' adds new extcon device and detect the
state/properties of external connector. Also, it notifies the
state/properties to the extcon consumer device.
- 'extcon consumer device' gets the change state/properties
from extcon provider device.
Prior to that, include/linux/extcon.h contains all exported API for
both provider and consumer device driver. To clarify the meaning of
header file and to remove the wrong use-case on consumer device,
this patch separates into extcon.h and extcon-provider.h.
[Description for include/linux/{extcon.h|extcon-provider.h}]
- extcon.h includes the extcon API and data structure for extcon consumer
device driver. This header file contains the following APIs:
: Register/unregister the notifier to catch the change of extcon device
: Get the extcon device instance
: Get the extcon device name
: Get the state of each external connector
: Get the property value of each external connector
: Get the property capability of each external connector
- extcon-provider.h includes the extcon API and data structure for extcon
provider device driver. This header file contains the following APIs:
: Include 'include/linux/extcon.h'
: Allocate the memory for extcon device instance
: Register/unregister extcon device
: Set the state of each external connector
: Set the property value of each external connector
: Set the property capability of each external connector
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Enable power saving for RTS5250S as following steps:
1.Set 0xFE58 to enable clock power management.
2.Check cfg space whether support L1SS or not.
3.If support L1SS, set 0xFF03 to free clkreq.
4.When entering idle status, enable aspm
and set parameters for L1SS and LTR.
5.Wnen entering run status, disable aspm
and set parameters for L1SS and LTR.
If entering L1SS mode successfully,
electric current will be below 2mA.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the driver boots only via device tree hence add a
dependency on CONFIG_OF. This leaves with a bunch of unused code
so clean that up. This patch also makes use of probe_new function
in place of the probe function so as to avoid passing i2c_device_id.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AXP813 PMIC has 7 DC-DC buck regulators, 16 LDOs (including the
fixed RTC LDO and 2 GPIO LDOs), and 1 switchable. The drive-vbus
feature is also supported. All the hardware details are very similar
to the AXP803, with the following exceptions:
- Extra DCDC7 buck regulator, with the same range as DCDC6
- SWitch now has a separate supply pin, instead of being chained
internaly from DCDC1
- RTC LDO output voltage is now 1.8V
- FLDO3 is an LDO with switchable supplies, but unconfigurable output
voltage. The voltage is always half that of its supply.
Support for FLDO3 is currently unimplemented, as it requires runtime
switching of its supplies, something the regulator subsystem does not
support. It is not used in either the reference designs nor actually
produced boards available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The output volume limits allow signals to be limited to specific levels
appropriate for the hardware attached. As this is a property of the
hardware itself these will be configured through device tree.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM9705, WM9712 and WM9713 are highly integrated codecs, with an
audio codec, DAC and ADC, GPIO unit and a touchscreen interface.
Historically the support was spread across drivers/input/touchscreen and
sound/soc/codecs. The sharing was done through ac97 bus sharing. This
model will not withstand the new AC97 bus model, where codecs are
discovered on runtime.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull MTD updates from Boris Brezillon:
"General updates:
- Constify pci_device_id in various drivers
- Constify device_type
- Remove pad control code from the Gemini driver
- Use %pOF to print OF node full_name
- Various fixes in the physmap_of driver
- Remove unused vars in mtdswap
- Check devm_kzalloc() return value in the spear_smi driver
- Check clk_prepare_enable() return code in the st_spi_fsm driver
- Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
- Fix memory leaks in the core
- Remove unused NAND locking support
- Rename nand.h into rawnand.h (preparing support for spi NANDs)
- Use NAND_MAX_ID_LEN where appropriate
- Fix support for 20nm Hynix chips
- Fix support for Samsung and Hynix SLC NANDs
- Various cleanup, improvements and fixes in the qcom driver
- Fixes for bugs detected by various static code analysis tools
- Fix mxc ooblayout definition
- Add a new part_parsers to tmio and sharpsl platform data in order
to define a custom list of partition parsers
- Request the reset line in exclusive mode in the sunxi driver
- Fix a build error in the orion-nand driver when compiled for ARMv4
- Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header Write a message for tag:"
* tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd: (74 commits)
mtd: nand: complain loudly when chip->bits_per_cell is not correctly initialized
mtd: nand: make Samsung SLC NAND usable again
mtd: nand: tmio: Register partitions using the parsers
mfd: tmio: Add partition parsers platform data
mtd: nand: sharpsl: Register partitions using the parsers
mtd: nand: sharpsl: Add partition parsers platform data
mtd: nand: qcom: Support for IPQ8074 QPIC NAND controller
mtd: nand: qcom: support for IPQ4019 QPIC NAND controller
dt-bindings: qcom_nandc: IPQ8074 QPIC NAND documentation
dt-bindings: qcom_nandc: IPQ4019 QPIC NAND documentation
dt-bindings: qcom_nandc: fix the ipq806x device tree example
mtd: nand: qcom: support for different DEV_CMD register offsets
mtd: nand: qcom: QPIC data descriptors handling
mtd: nand: qcom: enable BAM or ADM mode
mtd: nand: qcom: erased codeword detection configuration
mtd: nand: qcom: support for read location registers
mtd: nand: qcom: support for passing flags in DMA helper functions
mtd: nand: qcom: add BAM DMA descriptor handling
mtd: nand: qcom: allocate BAM transaction
mtd: nand: qcom: DMA mapping support for register read buffer
...
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
Pull MMC updates from Ulf Hansson:
"MMC core:
- Continue to refactor the mmc block code to prepare for blkmq
- Move mmc block debugfs into block module
- Next step for eMMC CMDQ by adding a new mmc host interface for it
- Move Kconfig option MMC_DEBUG from core to host
- Some additional minor improvements
MMC host:
- Declare structs as const when applicable
- Explicitly request exclusive reset control when applicable
- Improve some error paths and other various cleanups
- sdhci: Preparations to support SDHCI OMAP
- sdhci: Improve some PM related code
- sdhci: Re-factoring and modernizations
- sdhci-xenon: Add runtime PM and system sleep support
- sdhci-xenon: Add support for eMMC HS400 Enhanced Strobe
- sdhci-cadence: Add system sleep support
- sdhci-of-at91: Improve system sleep support
- dw_mmc: Add support for Hisilicon hi3660
- sunxi: Add support for A83T eMMC
- sunxi: Add support for DDR52 mode
- meson-gx: Add support for UHS-I SD-cards
- meson-gx: Cleanups and improvements
- tmio: Fix CMD12 (STOP) handling
- tmio: Cleanups and improvements
- renesas_sdhi: Add r8a7743/5 support
- renesas-sdhi: Add support for R-Car Gen3 SDHI DMAC
- renesas_sdhi: Cleanups and improvements"
* tag 'mmc-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (145 commits)
mmc: renesas_sdhi: Add r8a7743/5 support
mmc: meson-gx: fix __ffsdi2 undefined on arm32
mmc: sdhci-xenon: add runtime pm support and reimplement standby
mmc: core: Move mmc_start_areq() declaration
mmc: mmci: stop building qcom dml as module
mmc: sunxi: Reset the device at probe time
clk: sunxi-ng: Provide a default reset hook
mmc: meson-gx: rework tuning function
mmc: meson-gx: change default tx phase
mmc: meson-gx: implement voltage switch callback
mmc: meson-gx: use CCF to handle the clock phases
mmc: meson-gx: implement card_busy callback
mmc: meson-gx: simplify interrupt handler
mmc: meson-gx: work around clk-stop issue
mmc: meson-gx: fix dual data rate mode frequencies
mmc: meson-gx: rework clock init function
mmc: meson-gx: rework clk_set function
mmc: meson-gx: rework set_ios function
mmc: meson-gx: cfg init overwrite values
mmc: meson-gx: initialize sane clk default before clock register
...
Pull regulator updates from Mark Brown:
"This is an extremely quiet release for the regulator subsystem, it's
all fairly minor fixes and cleanups plus a few new drivers and ddevice
ID additions:
- Support for MediaTek MT6380, Ricoh RC5T619 and ST Voltage Reference
Buffers"
* tag 'regulator-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (24 commits)
regulator: Add support for stm32-vrefbuf
regulator: Add STM32 Voltage Reference Buffer
regulator: pv88090: Exception handling for out of bounds
regulator: da9063: Return an error code on probe failure
regulator: rn5t618: add RC5T619 PMIC support
regulator: ltc3589: constify i2c_device_id
regulator: fan53555: fix I2C device ids
regulator: add fixes with MT6397 dt-bindings shouldn't reference driver
regulator: add fixes with MT6323 dt-bindings shouldn't reference driver
regulator: add fixes with MT6311 dt-bindings shouldn't reference driver
regulator: Add document for MediaTek MT6380 regulator
regulator: mt6380: Add support for MT6380
regulator: pwm-regulator: Remove unneeded gpiod NULL check
regulator: core: fix a possible race in disable_work handling
regulator: fan53555: Use of_device_get_match_data() to simplify probe
regulator: of: regulator_of_get_init_data() missing of_node_get()
regulator: pwm-regulator: fix example syntax
regulator: Convert to using %pOF instead of full_name
regulator: cpcap: Add OF mode mapping
regulator: cpcap: Fix standby mode
...
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver update for 4.14-rc1.
Lots of different stuff in here, it's been an active development cycle
for some reason. Highlights are:
- updated binder driver, this brings binder up to date with what
shipped in the Android O release, plus some more changes that
happened since then that are in the Android development trees.
- coresight updates and fixes
- mux driver file renames to be a bit "nicer"
- intel_th driver updates
- normal set of hyper-v updates and changes
- small fpga subsystem and driver updates
- lots of const code changes all over the driver trees
- extcon driver updates
- fmc driver subsystem upadates
- w1 subsystem minor reworks and new features and drivers added
- spmi driver updates
Plus a smattering of other minor driver updates and fixes.
All of these have been in linux-next with no reported issues for a
while"
* tag 'char-misc-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (244 commits)
ANDROID: binder: don't queue async transactions to thread.
ANDROID: binder: don't enqueue death notifications to thread todo.
ANDROID: binder: Don't BUG_ON(!spin_is_locked()).
ANDROID: binder: Add BINDER_GET_NODE_DEBUG_INFO ioctl
ANDROID: binder: push new transactions to waiting threads.
ANDROID: binder: remove proc waitqueue
android: binder: Add page usage in binder stats
android: binder: fixup crash introduced by moving buffer hdr
drivers: w1: add hwmon temp support for w1_therm
drivers: w1: refactor w1_slave_show to make the temp reading functionality separate
drivers: w1: add hwmon support structures
eeprom: idt_89hpesx: Support both ACPI and OF probing
mcb: Fix an error handling path in 'chameleon_parse_cells()'
MCB: add support for SC31 to mcb-lpc
mux: make device_type const
char: virtio: constify attribute_group structures.
Documentation/ABI: document the nvmem sysfs files
lkdtm: fix spelling mistake: "incremeted" -> "incremented"
perf: cs-etm: Fix ETMv4 CONFIGR entry in perf.data file
nvmem: include linux/err.h from header
...
The TPS68470 device is an advanced power management
unit that powers a Compact Camera Module (CCM),
generates clocks for image sensors, drives a dual
LED for Flash and incorporates two LED drivers for
general purpose indicators.
This patch adds support for TPS68470 mfd device.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The X-Powers AXP813 PMIC is normally used with Allwinner's A83T SoC.
It has the same range of functions as other X-Powers PMICs, such as
DC-DC buck converter and linear regulator outputs, AC-IN and VBUS
power supplies, power button trigger, GPIOs, ADCs, and a battery
charger.
Note that the IRQ table given in the datasheet is incorrect: in IRQ
enable/status registers 1, there are separate IRQs for ACIN and VBUS,
instead of bits [7:5] being the same as bits [4:2]. So it shares the
same IRQs as the AXP803, rather than the AXP288.
This patch adds basic mfd support for it, with only the power button
enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the MFD part of the ROHM BD9571MWV-M PMIC driver and MAINTAINERS
entry. The MFD part only specifies the regmap bits for the PMIC and
binds the subdevs together.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for HiSilicon Hi6421v530 PMIC. Hi6421v530 communicates with
main SoC via memory-mapped I/O.
Hi6421v530 and Hi6421 are PMIC chips from the same vendor, HiSilicon,
but at different revisions. They share the same memory-mapped I/O
design. They differ in integrated devices, such as regulator details,
LDO voltage points.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STM32 Low-Power Timer hardware block can be used for:
- PWM generation
- IIO trigger (in sync with PWM)
- IIO quadrature encoder counter
PWM and IIO timer configuration are mixed in the same registers so
we need a multi fonction driver to be able to share those registers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is one SDHI instance on Gen2 which does not have the CBSY bit.
So, turn CBSY usage into an extra flag and set it accordingly. This has
the additional advantage that we can also set it for other incarnations
later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Chris Brandt <Chris.Brandt@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
o Make endian clean, make HW-endianness configurable.
o Use ioread*, iowrite* instead of __raw_readb,__raw_writeb
to also use memory-barriers when accessing HW-registers.
We do not want reordering to happen here.
Both changes are tightly coupled, so I do them in one patch
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace incorrect register offsett calculation by
direct configuration of bus_shift in mfd-cell.
Indirect definition of address-shift by resource size
was unobvious and was wrong (should have used a binary log).
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the driver to support Ricoh RC5T619.
Support the additional regulators and slightly different voltage ranges.
Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the introduction of sharpslpart partition parser we can now read the
offsets from NAND: we specify the list of the parsers as platform data, with
cmdlinepart and ofpart parsers first allowing to override the part. table
written in NAND. This is done in the board files using this driver.
Thus, we need to extend tmio_nand_data to consider the partition parsers.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This is the driver for the USB Type C cable detection mechanism
built into the ChromeOS Embedded Controller on systems that
have USB Type-C ports.
At present, this allows for the presence of display out, but in
future, it may also be used to notify host and device type cables
and the presence of power.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Chanwoo Choi <cw00.chio@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Pull chrome platform updates from Benson Leung:
"Changes in this pull request are around catching up cros_ec with the
internal chromeos-kernel versions of cros_ec, cros_ec_lpc, and
cros_ec_lightbar.
Also, switching maintainership from olof to bleung"
* tag 'chrome-platform-for-linus-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome : Add myself as Maintainer
platform/chrome: cros_ec_lightbar - hide unused PM functions
cros_ec: Don't signal wake event for non-wake host events
cros_ec: Fix deadlock when EC is not responsive at probe
cros_ec: Don't return error when checking command version
platform/chrome: cros_ec_lightbar - Avoid I2C xfer to EC during suspend
platform/chrome: cros_ec_lightbar - Add userspace lightbar control bit to EC
platform/chrome: cros_ec_lightbar - Control of suspend/resume lightbar sequence
platform/chrome: cros_ec_lightbar - Add lightbar program feature to sysfs
platform/chrome: cros_ec_lpc: Add MKBP events support over ACPI
platform/chrome: cros_ec_lpc: Add power management ops
platform/chrome: cros_ec_lpc: Add support for GOOG004 ACPI device
platform/chrome: cros_ec_lpc: Add support for mec1322 EC
platform/chrome: cros_ec_lpc: Add R/W helpers to LPC protocol variants
mfd: cros_ec: Add support for dumping panic information
cros_ec_debugfs: Pass proper struct sizes to cros_ec_cmd_xfer()
mfd: cros_ec: add debugfs, console log file
mfd: cros_ec: Add EC console read structures definitions
mfd: cros_ec: Add helper for event notifier.
