Pull regulator updates from Mark Brown:
"Quite a lot of core work this time around, though not 100% successful.
We gained support for runtime mode changes thanks to David Collins and
improved support for write only regulators (ones where we can't read
back the configuration) from Douglas Anderson.
There's been quite a bit of work from Linus Walleij on converting from
specfying GPIOs by numbers to descriptors. Sadly the testing turned
out to be less good than we had hoped and so a lot of this had to be
reverted.
We also have the start of updates to use coupled regulators from
Maciej Purski, unfortunately there are further problems there so the
last couple of patches have been reverted.
We also have new drivers for BD71837 and SY8106A devices, SAW
regulators on Qualcomm SPMI and dropped support for some preproduction
chips that never made it to market from the AB8500 driver"
* tag 'regulator-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (57 commits)
regulator: gpio: Revert
ARM: pxa, regulator: fix building ezx e680
regulator: Revert coupled regulator support again
regulator: wm8994: Fix shared GPIOs
regulator: max77686: Fix shared GPIOs
regulator: bd71837: BD71837 PMIC regulator driver
regulator: bd71837: Devicetree bindings for BD71837 regulators
regulator: gpio: Get enable GPIO using GPIO descriptor
regulator: fixed: Convert to use GPIO descriptor only
regulator: s2mps11: Fix boot on Odroid XU3
dt-bindings: qcom_spmi: Document SAW support
regulator: qcom_spmi: Add support for SAW
regulator: tps65090: Pass descriptor instead of GPIO number
regulator: s5m8767: Pass descriptor instead of GPIO number
regulator: pfuze100: Delete reference to ena_gpio
regulator: max8952: Pass descriptor instead of GPIO number
regulator: lp8788-ldo: Pass descriptor instead of GPIO number
regulator: lm363x: Pass descriptor instead of GPIO number
regulator: max8973: Pass descriptor instead of GPIO number
regulator: mc13xxx-core: Switch to SPDX identifier
...
Pull sound updates from Takashi Iwai:
"We've got many code additions at this cycle as a result of quite a few
new drivers. Below are highlights:
Core stuff:
- Fix the long-standing issue with the device registration order; the
control device is now registered at last
- PCM locking code cleanups for RT kernels
- Fixes for possible races in ALSA timer resolution accesses
- TLV offset definitions in uapi
ASoC:
- Many fixes for the topology stuff, including fixes for v4 ABI
compatibility
- Lots of cleanups / quirks for Intel platforms based on Realtek
CODECs
- Continued componentization works, removing legacy CODEC stuff
- Conversion of OMAP DMA to the new, more standard SDMA-PCM driver
- Fixes and updates to Cirrus Logic SoC drivers
- New Qualcomm DSP support
- New drivers for Analog SSM2305, Atmel I2S controllers, Mediatek
MT6351, MT6797 and MT7622, Qualcomm DSPs, Realtek RT1305, RT1306
and RT5668 and TI TSCS454
HD-audio:
- Finally better support for some CA0132 boards, allowing Windows
firmware
- HP Spectre x360 support along with a bulk of COEF stuff
- Blacklisting power save default some known boards reported on
Fedora
USB-audio:
- Continued improvements on UAC3 support; now BADD is supported
- Fixes / improvements for Dell WD15 dock
- Allow DMA coherent pages for PCM buffers for ARCH, MIPS & co
Others:
- New Xen sound frontend driver support
- Cache implementation and other improvements for FireWire DICE
- Conversions to octal permissions in allover places"
* tag 'sound-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (386 commits)
ASoC: dapm: delete dapm_kcontrol_data paths list before freeing it
ALSA: usb-audio: remove redundant check on err
ASoC: topology: Move skl-tplg-interface.h to uapi
ASoC: topology: Move v4 manifest header data structures to uapi
ASoC: topology: Improve backwards compatibility with v4 topology files
ALSA: pci/hda: Remove unused, broken, header file
ASoC: TSCS454: Add Support
ASoC: Intel: kbl: Move codec sysclk config to codec_init function
ASoC: simple-card: set cpu dai clk in hw_params
ALSA: hda - Handle kzalloc() failure in snd_hda_attach_pcm_stream()
ALSA: oxygen: use match_string() helper
ASoC: dapm: use match_string() helper
ASoC: max98095: use match_string() helper
ASoC: max98088: use match_string() helper
ASoC: Intel: bytcr_rt5651: Set card long_name based on quirks
ASoC: mt6797-mt6351: add hostless phone call path
ASoC: mt6797: add Hostless DAI
ASoC: mt6797: add PCM interface
ASoC: mediatek: export mtk-afe symbols as needed
ASoC: codecs: PCM1789: include gpio/consumer.h
...
This adds the generic core support for Cirrus Logic "Madera" class codecs.
These are complex audio codec SoCs with a variety of digital and analogue
I/O, onboard audio processing and DSPs, and other features.
These codecs are all based off a common set of hardware IP so can be
supported by a core of common code (with a few minor device-to-device
variations).
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Nikesh Oswal <Nikesh.Oswal@cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds a header file of register definitions for Cirrus
Logic "Madera" class codecs. These codecs are all based off a common
set of hardware IP so have a common register map (with a few minor
device-to-device variations).
The registers.h file is tool-generated directly from the hardware design
but has been manually stripped down to reduce size (full register
map is >44000 lines). All names are kept the same as datasheet names
so that they can be cross-referenced between source and datasheet without
confusion.
The register map layout is kept fully-defined rather than factored into
macros and/or block-indexing code. The major reasons for this are:
- #1 is that it makes the source highly greppable, which is important.
"What does the driver do with register bits XYZ" or "Where does it use
register bits XYZ" are commonly types of questions. These can be quickly
answered by a grep. Squashing definitions into generator macros or block-
indexing code is a way of defeating grep.
- most of the register definitions are used in tables, so a constant value
is required. Using generator macros make the table definition clunky and
obscure.
- the code is clearer when it's there in the source exactly what register
and field it is using
- it is easier to diff the register map of a new (unsupported) codec against
what is already supported and merge in differences
- it makes the register map available in source for maintenance/debugging
instead of having to refer back to the datasheet for a register map
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull chrome platform updates from Benson Leung:
- further changes from Dmitry related to the removal of platform data
from atmel_mxt_ts and chromeos_laptop.
This time, we have some changes that teach chromeos_laptop how to
supply acpi properties for some input devices so that the peripheral
driver doesn't have to do dmi matching on some Chromebook platforms.
- new Chromebook Tablet switch driver, which is useful for x86
convertible Chromebooks.
- other misc cleanup
* tag 'chrome-platform-for-linus-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
platform/chrome: Use to_cros_ec_dev more broadly
platform/chrome: chromeos_laptop: fix touchpad button mapping on Celes
platform: chrome: Add input dependency for tablet switch driver
platform/chrome: chromeos_laptop - supply properties for ACPI devices
platform/chrome: chromeos_tbmc - add SPDX identifier
platform: chrome: Add Tablet Switch ACPI driver
platform/chrome: cros_ec_lpc: do not try DMI match when ACPI device found
This is seen when COMPILE_TEST=y and MFD_STM32_TIMERS=n.
drivers/pwm/pwm-stm32.o: In function 'stm32_pwm_raw_capture':
pwm-stm32.c:... undefined reference to 'stm32_timers_dma_burst_read'
Fixes: 0c6609805b ("mfd: stm32-timers: Add support for DMAs")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move to_cros_ec_dev macro to cros_ec.h and use it when the private ec
object is needed from device object.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
This reverts commit 3c6b38d45f "regulator: wm8994: Pass
descriptor instead of GPIO number" as it has problems with shared
GPIOs similar to that on s2mps11.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should stop our worker thread while we're suspended. If we don't
then we'll get messages like:
cros-ec-spi spi5.0: spi transfer failed: -108
cros-ec-spi spi5.0: cs-deassert spi transfer failed: -108
cros-ec-ctl cros-ec-ctl.0.auto: EC communication failed
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node for the
regulator.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node for the
regulator.
This regulator supports passing platform data, but enable/sleep
regulators are looked up from the device tree exclusively, so
we can need not touch other files.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_index_optional() call.
This driver has supported passing a LDO enable GPIO for years,
yet this facility has never been put to use in the upstream kernel.
If someone desires to put in place GPIO control for the LDOs,
this can be done by adding a GPIO descriptor table in the MFD
nexus in drivers/mfd/lp8788.c for the LDO device when spawning the
MFD children, or using a board file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of passing a global GPIO number for the enable GPIO, pass
a descriptor looked up from the device tree node or the board file
decriptor table for the regulator.
There is a single board file passing the GPIOs for LDO1 and LDO2
through platform data, so augment this to pass descriptors
associated with the i2c device as well.
The special GPIO enable DT property for the enable GPIO is
nonstandard but this was accomodated in
commit 6a537d4846
"gpio: of: Support regulator nonstandard GPIO properties".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When AXP806 support was added, POK was incorrectly expanded to PWROK.
However, the datasheet lists them as POK[LSNP], which is the same as
on the AXP288. Furthermore, the registers associated with POK functions
are the same as the PEK on the other AXP PMICs. This suggests that
"POK" means "Power On Key", much like "PEK" means "Power Enable Key",
instead of "Power OK".
This patch changes the "PWROK" prefix to "POK" for these interrupts.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The axp20x driver has lots of mfd_cell and resource structs.
These can all be const-ified.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now GPIOD has support for both pdata systems and for non-standard DT
bindings the Arizona reset GPIO can be converted to use it. Worth
noting gpiod_set_raw_value_cansleep is used to match the behaviour
of the old GPIOs. This is because the part is fairly widely used and
it is unknown how many DTs are correctly setting active low through
device tree, so to avoid breaking any existing users it is best to
match the previous behaviour.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This reverts commit e04653a9dc.
It is no longer needed to install Chrome EC GPE handler to have
GPE enabled in suspend to idle path. It is found that with this
handler installed, EC wake up doesn't work because default EC
event handler that can wake up system is not getting called.
Signed-off-by: Wenkai Du <wenkai.du@intel.com>
Acked-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the GPL v2 license boilerplate and update with
the SPDX license identifier.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 2dc4940360 ("regulator: tps65218: Remove all the compatibles")
changes the probe function of drivers/regulator/tps65218-regulator.c so
that it iterates through all available regulators and assumes that the
regulator IDs are sequential and match the order present in the enum
tps65218_regulator_id. However, for some reason the much older commit
c0ea88b890 ("regulator: tps65218: add support for LS3 current
regulator") updated all arrays with LS3 at the end but added it second
to last for the enum.
Because of this long standing mismatch in order between the
tps65218_regulator_id enum and the regulator_desc array in the tps65218
regulator driver, the new probe function causes the strobe values to be
associated with the wrong regulator ID. This causes LDO1 to fail to
suspend in tps65218_pmic_set_suspend_disable due to not having anything
probes for its strobe value. Fix the order in the enum so the probe
function works as the update intended.
Fixes: 2dc4940360 ("regulator: tps65218: Remove all the compatibles")
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since commit 5812f0106c ("phy: exynos4: Remove duplicated defines of
PHY register defines") and commit 7a66647b25 ("phy: exynos: Use one
define for enable bit") all users of syscon Exynos PMU headers (for PHY
drivers) are converted to use different headers so these can be removed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Immutable branch between MFD and HWMON due for the v4.18 merge window
Immutable branch between MFD, Input and RTC due for the v4.18 merge window
Immutable branch between MFD and PWM due for the v4.18 merge window
Using input prescaler, capture unit will trigger DMA once every
configurable /2, /4 or /8 events (rising edge). This helps improve
period (only) capture accuracy at high rates.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for PMW input mode on pwm-stm32. STM32 timers support
period and duty cycle capture as long as they have at least two PWM
channels. One capture channel is used for period (rising-edge), one
for duty-cycle (falling-edge).
When there's only one channel available, only period can be captured.
Duty-cycle is simply zero'ed in such a case.
Capture requires exclusive access (e.g. no pwm output running at the
same time, to protect common prescaler).
Timer DMA burst mode (from MFD core) is being used, to take two
snapshots of capture registers (upon each period rising edge).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STM32 Timers can support up to 7 DMA requests:
- 4 channels, update, compare and trigger.
Optionally request part, or all DMAs from stm32-timers MFD core.
Also add routine to implement burst reads using DMA from timer registers.
This is exported. So, it can be used by child drivers, PWM capture
for instance (but not limited to).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The AB8540 was an evolved version of the AB8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the AB8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add definitions for the KEEPON_* bits in the "BKUP Mode Cnt" register,
which control the DDR rails to be kept powered when backup mode is
enabled.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This version is exists in the Samsung Galaxy Tab 10.1 which is based on the
Nvidia Tegra 2 board. The TPS658624 has the same SM2 voltage table as
TPS658623.
Signed-off-by: ryang <decatf@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The uid and die temperature can be read out on the ADIN7 using
input mux. Map uid and die temperature sensor to channels 16
and 17.
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull chrome platform updates from Benson Leung:
- a series from Dmitry to remove platform data from chromeos_laptop.c,
which was the only user of platform data for the atmel_mxt_ts driver.
- a series to clean up sysfs and debugfs for cros_ec
- other misc cleanups
* tag 'chrome-platform-for-linus-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform: (22 commits)
platform/chrome: mfd/cros_ec_dev: Add sysfs entry to set keyboard wake lid angle
platform/chrome: cros_ec_debugfs: Add PD port info to debugfs
platform/chrome: cros_ec_debugfs: Use octal permissions '0444'
platform/chrome: cros_ec_sysfs: use permission-specific DEVICE_ATTR variants
platform/chrome: cros_ec_sysfs: introduce to_cros_ec_dev define.
platform/chrome: cros_ec_sysfs: Modify error handling
platform/chrome: cros_ec_lpc: Add support for Google devices using custom coreboot firmware
platform/chrome: cros_ec_lpc: wake up from s2idle on Chrome EC
Input: atmel_mxt_ts - remove platform data support
platform/chrome: chromeos_laptop - discard data for unneeded boards
platform/chrome: chromeos_laptop - use device properties for Pixel
platform/chrome: chromeos_laptop - rely on I2C to set up interrupt trigger
platform/chrome: chromeos_laptop - use I2C notifier to create devices
platform/chrome: chromeos_laptop - parse DMI IRQ data once
platform/chrome: chromeos_laptop - rework i2c peripherals initialization
platform/chrome: chromeos_laptop - factor out getting IRQ from DMI
platform/chrome: chromeos_laptop - introduce pr_fmt()
platform/chrome: chromeos_laptop - stop setting suspend mode for Atmel devices
platform/chrome: chromeos_laptop - add SPDX identifier
Input: atmel_mxt_ts - switch ChromeOS ACPI devices to generic props
...
This adds a sysfs attribute (/sys/class/chromeos/cros_ec/kb_wake_angle)
used to set and get the keyboard wake lid angle. This attribute is
present only if 2 accelerometers are controlled by the EC.
This patch also moves the cros_ec features check before the device is
added so the features map obtained from the EC is ready on time.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Pull RTC updates from Alexandre Belloni:
"This contains a few series that have been in preparation for a while
and that will help systems with RTCs that will fail in 2038, 2069 or
2100.
Subsystem:
- Add tracepoints
- Rework of the RTC/nvmem API to allow drivers to discard struct
nvmem_config after registration
- New range API, drivers can now expose the useful range of the RTC
- New offset API the core is now able to add an offset to the RTC
time, modifying the supported range.
- Multiple rtc_time64_to_tm fixes
- Handle time_t overflow on 32 bit platforms in the core instead of
letting drivers do crazy things.
- remove rtc_control API
New driver:
- Intersil ISL12026
Drivers:
- Drivers exposing the RTC non volatile memory have been converted to
use nvmem
- Removed useless time and date validation
- Removed an indirection pattern that was a cargo cult from ancient
drivers
- Removed VLA usage
- Fixed a possible race condition in probe functions
- AB8540 support is dropped from ab8500
- pcf85363 now has alarm support"
* tag 'rtc-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (128 commits)
rtc: snvs: Fix usage of snvs_rtc_enable
rtc: mt7622: fix module autoloading for OF platform drivers
rtc: isl12022: use true and false for boolean values
rtc: ab8500: Drop AB8540 support
rtc: remove a warning during scripts/kernel-doc step
rtc: 88pm860x: remove artificial limitation
rtc: 88pm80x: remove artificial limitation
rtc: st-lpc: remove artificial limitation
rtc: mrst: remove artificial limitation
rtc: mv: remove artificial limitation
rtc: hctosys: Ensure system time doesn't overflow time_t
parisc: time: stop validating rtc_time in .read_time
rtc: pcf85063: fix clearing bits in pcf85063_start_clock
rtc: at91sam9: Set name of regmap_config
rtc: s5m: Remove VLA usage
rtc: s5m: Move enum from rtc.h to rtc-s5m.c
rtc: remove VLA usage
rtc: Add useful timestamp definitions
rtc: Add one offset seconds to expand RTC range
rtc: Factor out the RTC range validation into rtc_valid_range()
...
Pull staging/IIO updates from Greg KH:
"Here is the big set of Staging/IIO driver patches for 4.17-rc1.
It is a lot, over 500 changes, but not huge by previous kernel release
standards. We deleted more lines than we added again (27k added vs.
91k remvoed), thanks to finally being able to delete the IRDA drivers
and networking code.
We also deleted the ccree crypto driver, but that's coming back in
through the crypto tree to you, in a much cleaned-up form.
Added this round is at lot of "mt7621" device support, which is for an
embedded device that Neil Brown cares about, and of course a handful
of new IIO drivers as well.
And finally, the fsl-mc core code moved out of the staging tree to the
"real" part of the kernel, which is nice to see happen as well.
Full details are in the shortlog, which has all of the tiny cleanup
patches described.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (579 commits)
staging: rtl8723bs: Remove yield call, replace with cond_resched()
staging: rtl8723bs: Replace yield() call with cond_resched()
staging: rtl8723bs: Remove unecessary newlines from 'odm.h'.
staging: rtl8723bs: Rework 'struct _ODM_Phy_Status_Info_' coding style.
staging: rtl8723bs: Rework 'struct _ODM_Per_Pkt_Info_' coding style.
staging: rtl8723bs: Replace NULL pointer comparison with '!'.
staging: rtl8723bs: Factor out rtl8723bs_recv_tasklet() sections.
staging: rtl8723bs: Fix function signature that goes over 80 characters.
staging: rtl8723bs: Fix lines too long in update_recvframe_attrib().
staging: rtl8723bs: Remove unnecessary blank lines in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Change camel case to snake case in 'rtl8723bs_recv.c'.
staging: rtl8723bs: Add missing braces in else statement.
staging: rtl8723bs: Add spaces around ternary operators.
staging: rtl8723bs: Fix lines with trailing open parentheses.
staging: rtl8723bs: Remove unnecessary length #define's.
staging: rtl8723bs: Fix IEEE80211 authentication algorithm constants.
staging: rtl8723bs: Fix alignment in rtw_wx_set_auth().
staging: rtl8723bs: Remove braces from single statement conditionals.
staging: rtl8723bs: Remove unecessary braces from switch statement.
staging: rtl8723bs: Fix newlines in rtw_wx_set_auth().
...
Pull libata updates from Tejun Heo:
"Nothing too interesting.
The biggest change is refcnting fix for ata_host - the bug is recent
and can only be triggered on controller hotplug, so very few are
hitting it.
There also are a number of trivial license / error message changes and
some hardware specific changes"
* 'for-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (23 commits)
ahci: imx: add the imx8qm ahci sata support
libata: ensure host is free'd on error exit paths
ata: ahci-platform: add reset control support
ahci: imx: fix the build warning
ata: add Amiga Gayle PATA controller driver
ahci: imx: add the imx6qp ahci sata support
ata: change Tegra124 to Tegra
ata: ahci_tegra: Add AHCI support for Tegra210
ata: ahci_tegra: disable DIPM
ata: ahci_tegra: disable devslp for Tegra124
ata: ahci_tegra: initialize regulators from soc struct
ata: ahci_tegra: Update initialization sequence
dt-bindings: Tegra210: add binding documentation
libata: add refcounting to ata_host
pata_bk3710: clarify license version and use SPDX header
pata_falcon: clarify license version and use SPDX header
pata_it821x: Delete an error message for a failed memory allocation in it821x_firmware_command()
pata_macio: Delete an error message for a failed memory allocation in two functions
pata_mpc52xx: Delete an error message for a failed memory allocation in mpc52xx_ata_probe()
sata_dwc_460ex: Delete an error message for a failed memory allocation in sata_dwc_port_start()
...
Pull MMC updates from Ulf Hansson:
"MMC core:
- Export host capabilities through debugfs
- Export card RCA register via sysfs
- Improve card initializing sequence while enabling 4-bit bus
- Export a function to enable/disable wakeup for card detect IRQ
MMC host:
- dw_mmc: Add support for new hi3798cv200 variant
- dw_mmc: Remove support for some deprecated DT properties
- mediatek: Add support for new variant used on MT7622 SoC
- sdhci: Improve wakeup support for SDIO IRQs
- sdhci: Improve wakeup support for card detect IRQs
- sdhci-omap: Add tuning support
- sdhci_omap: Add UHS-I mode support
- sunxi: Prepare for runtime PM support via a few re-factorings
- tmio: deprecate "toshiba,mmc-wrprotect-disable" DT property
- tmio/renesas_sdhi: Consolidate code supporting write protect
- tmio: Improve DMA vs PIO handling
- tmio: Add support for IP-builtin card detection logic"
* tag 'mmc-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (55 commits)
mmc: renesas_sdhi: replace EXT_ACC with HOST_MODE
mmc: update sdio_claim_irq documentation
mmc: Export host capabilities to debugfs.
mmc: core: Disable HPI for certain Micron (Numonyx) eMMC cards
mmc: block: fix updating ext_csd caches on ioctl call
mmc: sunxi: Set our device drvdata earlier
mmc: sunxi: Move the reset deassertion before enabling the clocks
mmc: sunxi: Move resources management to separate functions
mmc: dw_mmc: add support for hi3798cv200 specific extensions of dw-mshc
dt-bindings: mmc: add bindings for hi3798cv200-dw-mshc
mmc: core: Export card RCA register via sysfs
mmc: renesas_sdhi: fix WP detection
mmc: core: Use memdup_user() rather than duplicating its implementation
mmc: dw_mmc-rockchip: correct property names in debug
mmc: sd: Remove redundant err assignment from mmc_read_switch
mmc: sdio: Check the return value of sdio_enable_4bit_bus
mmc: core: Don't try UHS-I mode if 4-bit mode isn't supported
arm64: dts: hi3660: remove 'num-slots' property for dwmmc
ARM: dts: lpc18xx: remove 'num-slots' property for dwmmc
arm64: dts: stratix10: remove 'num-slots' property for dwmmc
...
- Regarding to imx6q ahci sata, imx6qp ahci sata
has the reset mechanism. Add the imx6qp ahci sata
support in this commit.
- Use the specific reset callback for imx53 sata,
and use the default ahci_ops.softreset for the others.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Jonathan writes:
First round of new devices, features and cleanups for IIO in the 4.17 cycle.
Outside of IIO
* Strongly typed 64bit int_sqrt function needed by the mlx90632
New device support
* adc081s
- New driver supporting adc081s, adc101s and adc121s TI ADCs.
* ad5272
- New driver supproting the ad5272 and ad5274 ADI digital potentiometers
with DT bindings.
* axp20x_adc
- support the AXP813 ADC - includes rework patches to prepare for this.
* mlx90632
- New driver with dt bindings for this IR temperature sensor.
Features
* axp20x_adc
- Add DT bindings and probing.
* dht11
- The sensor has a wider range than advertised in the datasheet - support it.
* st_lsm6dsx
- Add hardware timestamp su9pport.
Cleanups
* ABI docs
- Update email contact for Matt Ranostay
* SPDX changes
- Matt Ranostay has moved his drivers over to SPDX. Currently we are making
this an author choice in IIO.
* ad7192
- Disable burnout current on misconfiguration. No actually effect as
they simply won't work otherwise.
* ad7476
- Drop a license definition that was replicating information in SPDX tag.
* ade7758
- Expand buf_lock to cover both buffer and state protection allowing
unintented uses of mlock in the core to be removed.
* ade7759
- Align parameters to opening parenthesis.
* at91_adc
- Depend on sysfs instead of selecting it - for try wide consistency.
* ccs811
- trivial naming type for a define.
* ep93xx
- Drop a redundant return as a result checking platform_get_resource.
* hts221
- Regmap conversion which simplifies the driver somewhat.
- Clean up some restricted endian cast warnings.
- Drop a trailing whitespace from a comment
- Drop an unnecessary get_unaligned by changing to the right 16bit data type.
* ms5611
- Fix coding style in the probe function (whitespace)
* st_accel
- Use strlcpy instead of strncpy to avoid potentially truncating a string.
When setting up a fixed regulator on the DA9055, pass a descriptor
instead of a global GPIO number. This facility is not used in the
kernel so we can easily just say that this should be a descriptor
if/when put to use.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull RTC updates from Alexandre Belloni:
"Not much this cycle. I've pushed the at32ap700x removal late but it is
unlikely to cause any issues.
Summary:
Subsystem:
- Move ABI documentation to Documentation/ABI
New driver:
- NXP i.MX53 SRTC
- Chrome OS EC RTC
Drivers:
- Remove at32ap700x
- Many fixes in various error paths"
* tag 'rtc-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: remove rtc-at32ap700x
Documentation: rtc: move iotcl interface documentation to ABI
Documentation: rtc: add sysfs file permissions
Documentation: rtc: move sysfs documentation to ABI
rtc: mxc_v2: remove __exit annotation
rtc: mxc_v2: Remove unnecessary platform_get_resource() error check
rtc: add mxc driver for i.MX53 SRTC
dt-bindings: rtc: add bindings for i.MX53 SRTC
rtc: r7301: Fix a possible sleep-in-atomic bug in rtc7301_set_time
rtc: r7301: Fix a possible sleep-in-atomic bug in rtc7301_read_time
rtc: omap: fix unbalanced clk_prepare_enable/clk_disable_unprepare
rtc: ac100: Fix multiple race conditions
rtc: sun6i: ensure rtc is kfree'd on error
rtc: cros-ec: add cros-ec-rtc driver.
mfd: cros_ec: Introduce RTC commands and events definitions.
rtc: stm32: Fix copyright
rtc: Remove unused RTC_DEVICE_NAME_SIZE
rtc: r9701: Remove r9701_remove function
rtc: brcmstb-waketimer: fix error handling in brcmstb_waketmr_probe()
The X-Powers AXP813 PMIC is really close to what is already done for
AXP20X/AXP22X.
There are two pairs of bits to set the rate (one for Voltage and Current
measurements and one for TS/GPIO0 voltage measurements) instead of one.
The register to set the ADC rates is different from the one for
AXP20X/AXP22X.
GPIO0 can be used as an ADC (measuring Volts) unlike for AXP22X.
The scales to apply to the different inputs are unlike the ones from
AXP20X and AXP22X.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The powerhold mask for TPS65917 is different when comapred to
the other palmas versions. Hence assign the right mask that enables
power off of tps65917 pmic correctly.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a driver for RAVE Supervisory Processor, an MCU implementing
various bits of housekeeping functionality (watchdoging, backlight
control, LED control, etc) on RAVE family of products by Zodiac
Inflight Innovations.
This driver implementes core MFD/serdev device as well as
communication subroutines necessary for commanding the device.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
