Dump command mailbox length printed was correct only if data_only flag
was set. For the case that data_only flag was clear the offset to stop
printing at was wrong and so the buffer printed was too short.
Changed the print loop to stop according to number of buffers in
mailbox.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Get the logic that calculates the number of blocks in a command mailbox
into a dedicated function.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
User-controlled application can cause multiple prints as below to flood
dmesg. Since knowledge of failed MKey release is important for debug,
let's decrease its level to debug.
mlx5_core 0000:00:04.0: mlx5_core_destroy_mkey:127:(pid 2352): failed
radix tree delete of mkey 0x1ed700
Reported-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In an SFP EEPROM values can be read to get information about a given SFP
module. One of those is the bitrate, which can be determined using a
nominal bitrate in addition with min and max values (in %). The SFP code
currently compute both BR,min and BR,max values thanks to this nominal
and min,max values.
This patch fixes the BR,min computation as the min value should be
subtracted to the nominal one, not added.
Fixes: 9962acf7fb ("sfp: add support for 1000Base-PX and 1000Base-BX10")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, skb->len and skb->data_len are set to the page size, not
the packet size. This causes the frame check sequence to not be
located at the "end" of the packet resulting in ethernet frame check
errors. The driver does work currently, but stricter kernel facing
networking solutions like OpenVSwitch will drop these packets as
invalid.
These changes set the packet size correctly so that these errors no
longer occur. The length does not include the frame check sequence, so
that subtraction was removed.
Tested on Oracle/SUN Multithreaded 10-Gigabit Ethernet Network
Controller [108e:abcd] and validated in wireshark.
Signed-off-by: Rob Taglang <rob@taglang.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_free_consistent() calls dma_free_coherent() to free tp->hw_stats
under spinlock and can trigger BUG_ON() in vunmap() because vunmap()
may sleep. Fix it by removing the spinlock and relying on the
TG3_FLAG_INIT_COMPLETE flag to prevent race conditions between
tg3_get_stats64() and tg3_free_consistent(). TG3_FLAG_INIT_COMPLETE
is always cleared under tp->lock before tg3_free_consistent()
and therefore tg3_get_stats64() can safely access tp->hw_stats
under tp->lock if TG3_FLAG_INIT_COMPLETE is set.
Fixes: f5992b72eb ("tg3: Fix race condition in tg3_get_stats64().")
Reported-by: Zumeng Chen <zumeng.chen@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It adds support for BCM89610 (Single-Port 10/100/1000BASE-T)
transceiver which is used in P3310 Tegra186 platform.
Signed-off-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While trying to support CHECKSUM_COMPLETE for IPV6 fragments,
I had to experiments various hacks in get_fixed_ipv6_csum().
I must admit I could not find how to implement this :/
However, get_fixed_ipv6_csum() does a lot of redundant operations,
calling csum_partial() twice.
First csum_partial() computes the checksum of saddr and daddr,
put in @csum_pseudo_hdr. Undone later in the second csum_partial()
computed on whole ipv6 header.
Then nexthdr is added once, added a second time, then substracted.
payload_len is added once, then substracted.
Really all this can be reduced to two add_csum(), to add back 6 bytes
that were removed by mlx4 when providing hw_checksum in RX descriptor.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3365711df0 ("sh_eth: WARN on access to a register not implemented
in a particular chip") added WARN_ON() to sh_eth_{read|write}() but not
to sh_eth_tsu_{read|write}(). Now that we've routed almost all TSU register
accesses (except TSU_ADR{H|L}<n> -- which are special) thru the latter
pair of accessors, it makes sense to check for the unimplemented TSU
registers as well...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no particularly good reason TSU_POST<n> registers get accessed
circumventing sh_eth_tsu_{read|write}() -- start using those, removing
(badly named) sh_eth_tsu_get_post_reg_offset(), while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary break statement in the default case of bw switch
block in mt76x2_mac_process_tx_rate routine
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have check if queue is not empty when start flushing queues on
by mac80211 callback, but we also can start flushing queues by internal
driver calls. So move check into rt2x00queue_flush_queue() to assure
we do not flush empty queue anytime.
Additionally add warning if we start to kick empty queue as in such
situation we set wrong index in the HW queue, what can confuse the HW
and have various negative consequences.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Only rt2800 subdriver of rt2x00 implement sta_add() and sta_remove(),
we do not need generic version of those.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following patch enables sending notifications also for events on FDB
entries that weren't added by the user. Give the drivers the information
necessary to distinguish between the two origins of FDB entries.
To maintain the current behavior, have switchdev-implementing drivers
bail out on notifications about non-user-added FDB entries. In case of
mlxsw driver, allow a call to mlxsw_sp_span_respin() so that SPAN over
bridge catches up with the changed FDB.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check number of CQEs for CQE version 2 reported by QUERY_AQ_CAP command.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use previously added resources to query FW support for multiple versions
of CQEs. Use the biggest version supported. For SDQs, it has no sense to
use version 2 as it does not introduce any new features, but it is
twice the size of CQE version 1.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce definitions of fields in CQE version 1 and 2. Also, introduce
common helpers that would call appropriate version-specific helpers
according to the version enum passed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.19.1.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The USB_DEVICE_INTERFACE_NUMBER matching macro assumes that
the { vendorid, productid, interfacenumber } set uniquely
identifies one specific function. This has proven to fail
for some configurable devices. One example is the Quectel
EM06/EP06 where the same interface number can be either
QMI or MBIM, without the device ID changing either.
Fix by requiring the vendor-specific class for interface number
based matching. Functions of other classes can and should use
class based matching instead.
Fixes: 03304bcb5e ("net: qmi_wwan: use fixed interface number matching")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is basically the same as 6e74d1749a ("r8152: replace
get_protocol with vlan_get_protocol"). Use vlan_get_protocol
instead of duplicating the functionality.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interpreting a member of an u16 array as u32 may result in a misaligned
access. Also it's not really intuitive to define a mac address variable
as array of three u16 words. Therefore use an array of six bytes that
is properly aligned for 32 bit access.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some chips have a non-zero function id, however instead of hardcoding
the id's (CSIAR_FUNC_NIC and CSIAR_FUNC_NIC2) we can get them
dynamically via PCI_FUNC(pci_dev->devfn). This way we can get rid
of the csi_ops.
In general csi is just a fallback mechanism for PCI config space
access in case no native access is supported. Therefore let's
try native access first.
I checked with Realtek regarding the functionality of config space
byte 0x070f and according to them it controls the L0s/L1
entrance latency.
Currently ASPM is disabled in general and therefore this value
isn't used. However we may introduce a whitelist for chips
where ASPM is known to work, therefore let's keep this code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only two places are left where rtl_generic_op() is used, so we can
inline it and simplify the code a little.
This change also avoids the overhead of unlocking/locking in case
the respective operation isn't set.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some longer if statements can be simplified by using switch
statements instead.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several switch statements can be significantly simplified by using
case ranges.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After merging r810x_pll_power_down/up and r8168_pll_power_down/up we
don't need member pll_power_ops any longer and can drop it, thus
simplifying the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
r810x_pll_power_down/up and r8168_pll_power_down/up have a lot in common,
so we can simplify the code by merging the former into the latter.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functionality of 810x_phy_power_up/down is covered by the default
clause in 8168_phy_power_up/down. Therefore we don't need these
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL_GIGA_MAC_VER_23/24 are configured by rtl_hw_start_8168cp_2()
and rtl_hw_start_8168cp_3() respectively which both apply
CPCMD_QUIRK_MASK, thus clearing bit ASF.
Bit ASF isn't set at any other place in the driver, therefore this
check can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use disable_irq_nosync() instead of disable_irq() as this might be
called in atomic context with netpoll.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently do not perform accounting in the driver and thus can't
reject routes before resources are exceeded.
However, in order to make users aware of the fact that routes are no
longer offloaded we can return an error for routes configured after the
abort mechanism was triggered.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 9776d32537 ("net: Move call_fib_rule_notifiers up in
fib_nl_newrule") it is possible to forbid the installation of
unsupported FIB rules.
Have mlxsw return an error for non-default FIB rules in addition to the
existing extack message.
Example:
# ip rule add from 198.51.100.1 table 10
Error: mlxsw_spectrum: FIB rules not supported.
Note that offload is only aborted when non-default FIB rules are already
installed and merely replayed during module initialization.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device id's 0x5019, 0x501a and 0x501b for T5
cards.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dual_mac mode packets arrived on one port should not be forwarded by
switch hw to another port. Only Linux Host can forward packets between
ports. The below test case (reported in [1]) shows that packet arrived on
one port can be leaked to anoter (reproducible with dual port evms):
- connect port 1 (eth0) to linux Host 0 and run tcpdump or Wireshark
- connect port 2 (eth1) to linux Host 1 with vlan 1 configured
- ping <IPx> from Host 1 through vlan 1 interface.
ARP packets will be seen on Host 0.
Issue happens because dual_mac mode is implemnted using two vlans: 1 (Port
1+Port 0) and 2 (Port 2+Port 0), so there are vlan records created for for
each vlan. By default, the ALE will find valid vlan record in its table
when vlan 1 tagged packet arrived on Port 2 and so forwards packet to all
ports which are vlan 1 members (like Port.
To avoid such behaviorr the ALE VLAN ID Ingress Check need to be enabled
for each external CPSW port (ALE_PORTCTLn.VID_INGRESS_CHECK) so ALE will
drop ingress packets if Rx port is not VLAN member.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC firmware does not support disabling rx vlan offload, but the VF driver
incorrectly indicates that it is supported. The PF driver already does the
correct indication by clearing the NETIF_F_HW_VLAN_CTAG_RX bit in its
netdev->hw_features. So just do the same thing in the VF.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Acked-by: Prasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware requires that the ttl value for an encapsulating ipv4 tunnel
header be included as an action field. Prior to the support of Geneve
tunnel encap (when ttl set was removed completely), ttl value was
extracted from the tunnel key. However, tests have shown that this can
still produce a ttl of 0.
Fix the issue by setting the namespace default value for each new tunnel.
Follow up patch for net-next will do a full route lookup.
Fixes: 3ca3059dc3 ("nfp: flower: compile Geneve encap actions")
Fixes: b27d6a95a7 ("nfp: compile flower vxlan tunnel set actions")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the current statistics for size 8192~12287 are only valid for GE,
the ranges of 8192~9216 and 9217~12287 are valid only for LGE/CGE, and are
always 0 for GE interfaces. it is easy to cause confusion when viewing the
packet statistics using the command ethtool -S.
This patch removes the 8192~12287 range of packet statistics and uses the
8192~9216 and 9217~12287 ranges for statistics. This change depends on the
firmware upgrade.
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two level of vlan tables in hardware, one is port vlan
which is shared by all functions, the other one is function
vlan table, each function has it's own function vlan table.
Currently, PF sets the port vlan table, and vf sets the function
vlan table, which will cause packet lost problem.
This patch fixes this problem by setting both vlan table, and
use hdev->vlan_table to manage thet port vlan table.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If head has invlid value then a dead loop can be triggered in
hclge_cmd_csq_clean. This patch adds sanity check for this case.
Fixes: 68c0a5c706 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd
Interface Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check to support autoneg(ethtool -A) only when PHY
is attached with the port.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility
Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phy exists, phy_addr must less than PHY_MAX_ADDR.
If not, hclge_mac_mdio_config should return error.
And for fiber(phy_addr=0xff), it does not need hclge_mac_mdio_config.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some of the missed error legs in the initialization
function of the ae device. This might cause leaks in case of failure.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer
Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
