This adds support for U32 filter by using an HW only feature called
Flexible RX Parser. This allow us to match any given packet field with a
pattern and accept/reject or even route the packet to a specific DMA
channel.
Right now we only support acception or rejection of frame and we only
support simple rules. Though, the Parser has the flexibility of jumping to
specific rules as an if condition so complex rules can be established.
This is only supported in GMAC5.10+.
The following commands can be used to test this code:
1) Setup an ingress qdisk:
# tc qdisc add dev eth0 handle ffff: ingress
2) Setup a filter (e.g. filter by IP):
# tc filter add dev eth0 parent ffff: protocol ip u32 match ip \
src 192.168.0.3 skip_sw action drop
In every tests performed we always used the "skip_sw" flag to make sure
only the RX Parser was involved.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for Microchip LAN87XX T1 PHYs
This patch support driver for Microchp T1 PHYs.
There will be followup patches to this driver to support T1 PHY
features such as cable diagnostics, signal quality indicator(SQI),
sleep and wakeup (TC10) support.
Signed-off-by: Nisar Sayed <Nisar.Sayed@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending packets as fast as possible using "cangen -g 0 -i -x", the
HI-3110 occasionally latches the interrupt pin high on completion of a
packet, but doesn't set the TXCPLT bit in the INTF register. The INTF
register contains 0x00 as if no interrupt has occurred. Even waiting
for a few milliseconds after the interrupt doesn't help.
Work around this apparent erratum by instead checking the TXMTY bit in
the STATF register ("TX FIFO empty"). We know that we've queued up a
packet for transmission if priv->tx_len is nonzero. If the TX FIFO is
empty, transmission of that packet must have completed.
Note that this is congruent with our handling of received packets, which
likewise gleans from the STATF register whether a packet is waiting in
the RX FIFO, instead of looking at the INTF register.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
hi3110_get_berr_counter() may run concurrently to the rest of the driver
but neglects to acquire the lock protecting access to the SPI device.
As a result, it and the rest of the driver may clobber each other's tx
and rx buffers.
We became aware of this issue because transmission of packets with
"cangen -g 0 -i -x" frequently hung. It turns out that agetty executes
->do_get_berr_counter every few seconds via the following call stack:
CPU: 2 PID: 1605 Comm: agetty
[<7f3f7500>] (hi3110_get_berr_counter [hi311x])
[<7f130204>] (can_fill_info [can_dev])
[<80693bc0>] (rtnl_fill_ifinfo)
[<806949ec>] (rtnl_dump_ifinfo)
[<806b4834>] (netlink_dump)
[<806b4bc8>] (netlink_recvmsg)
[<8065f180>] (sock_recvmsg)
[<80660f90>] (___sys_recvmsg)
[<80661e7c>] (__sys_recvmsg)
[<80661ec0>] (SyS_recvmsg)
[<80108b20>] (ret_fast_syscall+0x0/0x1c)
agetty listens to netlink messages in order to update the login prompt
when IP addresses change (if /etc/issue contains \4 or \6 escape codes):
https://git.kernel.org/pub/scm/utils/util-linux/util-linux.git/commit/?id=e36deb6424e8
It's a useful feature, though it seems questionable that it causes CAN
bit error statistics to be queried.
Be that as it may, if hi3110_get_berr_counter() is invoked while a frame
is sent by hi3110_hw_tx(), bogus SPI transfers like the following may
occur:
=> 12 00 (hi3110_get_berr_counter() wanted to transmit
EC 00 to query the transmit error counter,
but the first byte was overwritten by
hi3110_hw_tx_frame())
=> EA 00 3E 80 01 FB (hi3110_hw_tx_frame() wanted to transmit a
frame, but the first byte was overwritten by
hi3110_get_berr_counter() because it wanted
to query the receive error counter)
This sequence hangs the transmission because the driver believes it has
sent a frame and waits for the interrupt signaling completion, but in
reality the chip has never sent away the frame since the commands it
received were malformed.
Fix by acquiring the SPI lock in hi3110_get_berr_counter().
I've scrutinized the entire driver for further unlocked SPI accesses but
found no others.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Casey Fitzpatrick <casey.fitzpatrick@timesys.com>
Cc: Stef Walter <stefw@redhat.com>
Cc: Karel Zak <kzak@redhat.com>
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Saeed Mahameed says:
====================
mlx5-updates-2018-05-07
mlx5 core driver misc cleanups and updates:
- fix spelling mistake: "modfiy" -> "modify"
- Cleanup unused field in Work Queue parameters
- dump_command mailbox length printed
- Refactor num of blocks in mailbox calculation
- Decrease level of prints about non-existent MKEY
- remove some extraneous spaces in indentations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some BPF capabilities carry no value, they simply indicate feature
is present. Our capability parsing loop will exit early if last
capability is zero-length because it's looking for more than 8 bytes
of data (8B is our TLV header length). Allow the last capability to
be zero-length.
This bug would lead to driver failing to probe with the following error
if the last capability FW advertises is zero-length:
nfp: BPF capabilities left after parsing, parsed:92 total length:100
nfp: invalid BPF capabilities at offset:92
Note the "parsed" and "length" values are 8 apart.
No shipping FW runs into this issue, but we can't guarantee that will
remain the case.
Fixes: 77a844ee65 ("nfp: bpf: prepare for parsing BPF FW capabilities")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
BPF has access to all internal FW datapath structures. Including
the structure containing RX queue selection. With little coordination
with the datapath we can let the offloaded BPF select the RX queue.
We just need a way to tell the datapath that queue selection has already
been done and it shouldn't overwrite it. Define a bit to tell datapath
BPF already selected a queue (QSEL_SET), if the selected queue is not
enabled (>= number of enabled queues) datapath will perform normal RSS.
BPF queue selection on the NIC can be used to replace standard
datapath RSS with fully programmable BPF/XDP RSS.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
We don't actually need to check if the host mbx is ready when queuing
MAC requests, because these are not handled by a special queue which
queues up requests until the mailbox is capable of handling them.
Pull these requests outside the fm10k_host_mbx_ready() check, as it is
not necessary.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Avoid potential bugs with fm10k_add_stat_strings and
fm10k_add_ethtool_stats by using a macro to calculate the ARRAY_SIZE
when passing. This helps ensure that the size is always correct.
Note that it assumes we only pass static const fm10k_stat arrays, and
that evaluation of the argument won't have side effects.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using a fixed prefix string we setup before each call to
fm10k_add_stat_strings, modify the helper to take variadic arguments and
pass them to vsnprintf. This requires changing the fm10k_stat strings to
take % format specifiers where necessary, but the resulting code is much
simpler.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Share some of the code for setting up fm10k_stat macros by implementing
an FM10K_STAT_FIELDS macro which we can use when setting up the type
specific macros.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have support for accelerating macvlan devices via the
.ndo_dfwd_add_station() netdev op. These accelerated macvlan MAC
addresses are stored in the l2_accel structure, separate from the
unicast or multicast address lists.
If a VLAN is added on top of the macvlan device by the stack, traffic
will not properly flow to the macvlan. This occurs because we fail to
setup the VLANs for l2_accel MAC addresses.
In the non-offloaded case the MAC address is added to the unicast
address list, and thus the normal setup for enabling VLANs works as
expected.
We also need to add VLANs marked from .ndo_vlan_rx_add_vid() into the
l2_accel MAC addresses. Otherwise, VLAN traffic will not properly be
received by the VLAN devices attached to the offloaded macvlan devices.
Fix this by adding necessary logic to setup VLANs not only for the
unicast and multicast addresses, but also the l2_accel list. We need
similar logic in dfwd_add_station, dfwd_del_station, fm10k_update_vid,
and fm10k_restore_rx_state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While carrying energy detection(ED) tests, the chip will stop
transmission upon detecting an energy in the connected channel.
As a feedback, driver will stop dequeuing TX packets and due to
which wmm_tx_pending keep incremeting. Once wmm_tx_pending
reaches 100, driver calls netif_tx_stop_queue(). If TX ques is
not restarted within 5(watchdog_timeo) seconds, it will result in
TX timeout.
The ED test is carried out for one minute and the current
threshold of 100 is easily overcome by the traffic, cuasing TX
timeouts. To fix this increase the threshold to 400.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Nothing that is defined in 11ac.h is referenced in cmdevt.c.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for the BCM43364 chipset via an SDIO interface, as used in
e.g. the Murata 1FX module.
The BCM43364 uses the same firmware as the BCM43430 (which is already
included), the only difference is the omission of Bluetooth.
However, the SDIO_ID for the BCM43364 is 02D0:A9A4, giving it a MODALIAS
of sdio:c00v02D0dA9A4, which doesn't get recognised and hence doesn't
load the brcmfmac module. Adding the 'A9A4' ID in the appropriate place
triggers the brcmfmac driver to load, and then correctly use the
firmware file 'brcmfmac43430-sdio.bin'.
Signed-off-by: Sean Lanigan <sean@lano.id.au>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two enumerations bt_total_ant_num and bt_ant_num are identical, so one
can be removed.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit a92a08499b "r8169: improve runtime pm in general and
suspend unused ports" interfaces w/o link are runtime-suspended after
10s. On systems where drivers take longer to load this can lead to the
situation that the interface is runtime-suspended already when it's
initially brought up.
This shouldn't be a problem because rtl_open() resumes MAC/PHY.
However with at least one chip version the interface doesn't properly
come up, as reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=199549
The vendor driver uses a delay to give certain chip versions some
time to resume before starting the PHY configuration. So let's do
the same. I don't know which chip versions may be affected,
therefore apply this delay always.
This patch was reported to fix the issue for RTL8168h.
I was able to reproduce the issue on an Asus H310I-Plus which also
uses a RTL8168h. Also in my case the patch fixed the issue.
Reported-by: Slava Kardakov <ojab@ojab.ru>
Tested-by: Slava Kardakov <ojab@ojab.ru>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When computing the bitrate using values read from an SFP module EEPROM,
we use the nominal BR plus BR,min and BR,max to determine the
boundaries. But in some cases BR,min and BR,max aren't provided, which
led the SFP code to end up having the nominal value for both the minimum
and maximum bitrate values. When using a passive cable, the nominal
value should be used as the maximum one, and there is no minimum one
so we should use 0.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
pull-request: can 2018-05-08
this is a pull request for 7 patches for net/master.
The first patch is by Jakob Unterwurzacher and increases the severity of
bus-off messages in the generic CAN device infrastructure. The next two patches
are by Uwe Kleine-König and fix the endianess detection in the flexcan driver.
Jimmy Assarsson's patch for the kvaser driver corrects the stats counter for
dropped tx-messages. Geert Uytterhoeven provides one patch and Sergei Shtylyov
two patches for the rcan_canfd device tree binding description.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: ieee802154 2018-05-08
An update from ieee802154 for your *net* tree.
Two fixes for the mcr20a driver, which was being added in the 4.17 merge window,
by Gustavo and myself.
The atusb driver got a change to GFP_KERNEL where no GFP_ATOMIC is needed by
Jia-Ju.
The last and most important fix is from Alex to get IPv6 reassembly working
again for the ieee802154 6lowpan adaptation. This got broken in 4.16 so please
queue this one also up for the 4.16 stable tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code already forwards the VF MAC address to the PF, except
in one case. If the VF driver gets a valid MAC address from the firmware
during probe time, it will not forward the MAC address to the PF,
incorrectly assuming that the PF already knows the MAC address. This
causes "ip link show" to show zero VF MAC addresses for this case.
This assumption is not correct. Newer firmware remembers the VF MAC
address last used by the VF and provides it to the VF driver during
probe. So we need to always forward the VF MAC address to the PF.
The forwarded MAC address may now be the PF assigned MAC address and so we
need to make sure we approve it for this case.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SFP+ modules, 0xA2 page is available only when Diagnostic Monitoring
Type [Address A0h, Byte 92] is implemented. Extend bnxt_get_module_info(),
to read optical diagnostics support at offset 92(0x5c) and set eeprom_len
length to ETH_MODULE_SFF_8436_LEN (to exclude A2 page), if dianostics is
not supported.
Also in bnxt_get_module_info(), module id is read from offset 0x5e which
is not correct. It was working by accident, as offset was not effective
without setting enables flag in the firmware request. SFP module id is
present at location 0. Fix this by removing the offset and read it
from location 0.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only non-NPAR PFs need to actively check and manage unsupported link
speeds. NPAR functions and VFs do not control the link speed and
should skip the unsupported speed detection logic, to avoid warning
messages from firmware rejecting the unsupported firmware calls.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change to reduce delay granularity waiting for firmware
reponse has caused a regression. With a tighter delay loop,
the driver may see the beginning part of the response faster.
The original 5 usec delay to wait for the rest of the message
is not long enough and some messages are detected as invalid.
Increase the maximum wait time from 5 usec to 20 usec. Also, fix
the debug message that shows the total delay time for the response
when the message times out. With the new logic, the delay time
is not fixed per iteration of the loop, so we define a macro to
show the total delay time.
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 88462d2a78 ("can: flexcan: Remodel FlexCAN register r/w APIs
for big endian FlexCAN controllers.") the following logic was
implemented:
if the dt property "big-endian" is given or
the device is compatible to "fsl,p1010-flexcan":
use big-endian mode;
else
use little-endian mode;
This relies on commit d50f4630c2 ("arm: dts: Remove p1010-flexcan
compatible from imx series dts") which was applied a few commits later.
Without this commit (or an old device tree used for booting a new
kernel) the flexcan devices on i.MX25, i.MX28, i.MX35 and i.MX53 match
the 'the device is compatible to "fsl,p1010-flexcan"' test and so are
switched erroneously to big endian mode.
Instead of the check above put a quirk in devtype data and rely on
of_match_device yielding the most compatible match
Fixes: 88462d2a78 ("can: flexcan: Remodel FlexCAN register r/w APIs for big endian FlexCAN controllers.")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Gavin Schenk <g.schenk@eckelmann.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.16
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
bus-off is usually caused by hardware malfunction or configuration error
(baud rate mismatch) and causes a complete loss of communication.
Increase the "bus-off" message's severity from netdev_dbg() to
netdev_info() to make it visible to the user.
A can interface going into bus-off is similar in severity to ethernet's
"Link is Down" message, which is also printed at info level.
It is debatable whether the the "restarted" message should also be
changed to netdev_info() to make the interface state changes
comprehensible from the kernel log. I have chosen to keep the
"restarted" message at dbg for now as the "bus-off" message should be
enough for the user to notice and investigate the problem.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Cc: linux-can@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds PCI device IDs to support 25GE and 100GE card:
1. Add device id 0x0201 for HINIC 100GE dual port card.
2. Add device id 0x0200 for HINIC 25GE dual port card.
3. Macro of device id 0x1822 is modified for HINIC 25GE quad port card.
Signed-off-by: Zhao Chen <zhaochen6@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver should use pci_alloc_irq_vectors return value to correct number
of allocated vectors and napi instances. Otherwise it'll panic later
in pci_irq_vector.
Driver also should allow more than one MSI vectors to be allocated.
Error return path from pci_alloc_irq_vectors is also fixed to revert
resources in a correct sequence when error happens.
Reported-by: Long, Nicholas <nicholas.a.long@baesystems.com>
Fixes: 23ee07a ("net: aquantia: Cleanup pci functions module")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In particular, not reporting SG forced skbs to be linear for vlan
interfaces over atlantic NIC.
With this fix it is possible to enable SG feature on device and
therefore optimize performance.
Reported-by: Ma Yuying <yuma@redhat.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver changes for supporting the Unified Fabric Port
(UFP). This is a new paritioning mode wherein MFW provides the set of
parameters to be used by the device such as traffic class, outer-vlan
tag value, priority type etc. Drivers receives this info via notifications
from mfw and configures the hardware accordingly.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support for new Multi function mode wherein the traffic
classification is done based on the 802.1ad tagging and the outer vlan tag
provided by the management firmware.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`mf_mode' field indicates the multi-partitioning mode the device is
configured to. This method doesn't scale very well, adding a new MF mode
requires going over all the existing conditions, and deciding whether those
are needed for the new mode or not.
The patch defines a set of bit-fields for modes which are derived according
to the mode info shared by the MFW and all the configuration would be made
according to those. To add a new mode, there would be a single place where
we'll need to go and choose which bits apply and which don't.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the mv88e6xxx switches have the PHYs at address 0, 1, 2, ...
The 6341 however has the PHYs at 0x10, 0x11, 0x12. Add a parameter to
the info structure for this base address.
Testing of 6f88284f3b ("net: dsa: mv88e6xxx: Add MDIO interrupts for
internal PHYs") was performed on the 6341. So it works only on the
6341. Use this base information to correctly set the interrupt.
Fixes: 6f88284f3b ("net: dsa: mv88e6xxx: Add MDIO interrupts for internal PHYs")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict, a CHECK was placed into an if() statement
in net-next, whilst a newline was added to that CHECK
call in 'net'. Thanks to Daniel for the merge resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
Support setting the link speed of CN23XX-225 cards (which can do 25Gbps or
10Gbps) via ethtool_ops.set_link_ksettings.
Also fix the function assigned to ethtool_ops.get_link_ksettings to use the
new link_ksettings api completely (instead of partially via
ethtool_convert_legacy_u32_to_link_mode).
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Acked-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following warnings:
warning: pointer targets in passing argument 1 of
‘is_valid_ether_addr’ differ in signedness [-Wpointer-sign]
if (mac_addr && is_valid_ether_addr(mac_addr)) {
^~~~~~~~
expected ‘const u8 * {aka const unsigned char *}’ but argument
is of type ‘const char *’
static inline bool is_valid_ether_addr(const u8 *addr)
^~~~~~~~~~~~~~~~~~~
warning: pointer targets in passing argument 2 of
‘ether_addr_copy’ differ in signedness [-Wpointer-sign]
ether_addr_copy(ndev->dev_addr, mac_addr);
^~~~~~~~
expected ‘const u8 * {aka const unsigned char *}’ but argument
is of type ‘const char *’
static inline void ether_addr_copy(u8 *dst, const u8 *src)
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix issue where nixge_get_nvmem_address() returns a non-NULL
return value on a failed nvmem_cell_get() that causes an invalid
access when error value encoded in pointer is dereferenced.
Furthermore ensure that buffer allocated by nvmem_cell_read()
actually gets kfreed() if the function succeeds.
Fixes commit 492caffa8a ("net: ethernet: nixge: Add support for
National Instruments XGE netdev")
Reported-by: Alex Williams <alex.williams@ni.com>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vortex_boomerang_interrupt() is invoked from vortex_tx_timeout() or
poll_vortex() interrupts must be disabled. This detaches the interrupt
disable logic from locking which requires patching for PREEMPT_RT.
The advantage of avoiding spin_lock_irqsave() in the interrupt handler is
minimal, but converting it removes all the extra code for callers which
come not from interrupt context.
Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locking is done in the same way in _vortex_interrupt() and
_boomerang_interrupt(). To prevent duplication, move the locking into the
calling vortex_boomerang_interrupt() function.
No functional change.
Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If vp->full_bus_master_tx is set, vp->full_bus_master_rx is set as well
(see vortex_probe1()). Therefore the conditionals for the decision if
boomerang or vortex ISR is executed have the same result. Instead of
repeating the explicit conditional execution of the boomerang/vortex ISR,
move it into an own function.
No functional change.
Cc: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
'hwname' should be freed before leaving from the error handling cases,
otherwise it will cause mem leak
Fixes: cb1a5bae56 ("mac80211_hwsim: add permanent mac address option for new radios")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kernel will now replace map fds with actual pointer before
calling the offload prepare. We can identify those pointers
and replace them with NFP table IDs instead of loading the
table ID in code generated for CALL instruction.
This allows us to support having the same CALL being used with
different maps.
Since we don't want to change the FW ABI we still need to
move the TID from R1 to portion of R0 before the jump.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add support for the perf_event_output family of helpers.
The implementation on the NFP will not match the host code exactly.
The state of the host map and rings is unknown to the device, hence
device can't return errors when rings are not installed. The device
simply packs the data into a firmware notification message and sends
it over to the host, returning success to the program.
There is no notion of a host CPU on the device when packets are being
processed. Device will only offload programs which set BPF_F_CURRENT_CPU.
Still, if map index doesn't match CPU no error will be returned (see
above).
Dropped/lost firmware notification messages will not cause "lost
events" event on the perf ring, they are only visible via device
error counters.
Firmware notification messages may also get reordered in respect
to the packets which caused their generation.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
For asynchronous events originating from the device, like perf event
output, we need to be able to make sure that objects being referred
to by the FW message are valid on the host. FW events can get queued
and reordered. Even if we had a FW message "barrier" we should still
protect ourselves from bogus FW output.
Add a reverse-mapping hash table and record in it all raw map pointers
FW may refer to. Only record neutral maps, i.e. perf event arrays.
These are currently the only objects FW can refer to. Use RCU protection
on the read side, update side is under RTNL.
Since program vs map destruction order is slightly painful for offload
simply take an extra reference on all the recorded maps to make sure
they don't disappear.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Remove the 'linear' field from struct mlx5_wq_param.
It is redundant, set but never read.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
