Add flag tc_flower_initialized to indicate the
completion if tc flower initialization.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver currently crashes on at91rm9200 with the following trace:
Unable to handle kernel NULL pointer dereference at virtual address 00000014
[...]
[<c031da44>] (macb_rx_desc) from [<c031f2bc>] (at91ether_open+0x2e8/0x3f8)
[<c031f2bc>] (at91ether_open) from [<c041e8d8>] (__dev_open+0x120/0x13c)
[<c041e8d8>] (__dev_open) from [<c041ec08>] (__dev_change_flags+0x17c/0x1a8)
[<c041ec08>] (__dev_change_flags) from [<c041ec4c>] (dev_change_flags+0x18/0x4c)
[<c041ec4c>] (dev_change_flags) from [<c07a5f4c>] (ip_auto_config+0x220/0x10b0)
[<c07a5f4c>] (ip_auto_config) from [<c000a4fc>] (do_one_initcall+0x78/0x18c)
[<c000a4fc>] (do_one_initcall) from [<c0783e50>] (kernel_init_freeable+0x184/0x1c4)
[<c0783e50>] (kernel_init_freeable) from [<c0574d70>] (kernel_init+0x8/0xe8)
[<c0574d70>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
Solve that by initializing bp->queues[0].bp in at91ether_init (as is done
in macb_init).
Fixes: ae1f2a56d2 ("net: macb: Added support for many RX queues")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following warning is seen when rmmod hinic. This is because affinity
value is not reset before calling free_irq(). This patch fixes it.
[ 55.181232] WARNING: CPU: 38 PID: 19589 at kernel/irq/manage.c:1608
__free_irq+0x2aa/0x2c0
Fixes: 352f58b0d9 ("net-next/hinic: Set Rxq irq to specific cpu for NUMA")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switching between low gain (high RSSI) and high gain settings, it
can take a few seconds to adjust to the current environment.
This can lead to short periods of time with extreme packet loss.
When switching from low_gain=1 to low_gain=2, start with the same gain
adjustment value instead of the lowest to avoid spikes of huge numbers
of false CCA events
Also avoid resetting adjustment values on switching between low_gain
values 0 and 1, since it affects only the upper limit of vga adjustment
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This preserves more sensitivity when weak stations are active and avoids
counting signal measurements from other unrelated networks
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Useful for debugging gain adjustment issues triggered by signal strength
changes.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The range should only be limited to 4 for really weak signals, for all
other gain settings the range is 16.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
They will be read on the next calibration step without gain change and
must not count earlier events
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The lowest bit should be set to 0 only for strong links, not for weak
ones.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The gain should be reduced only for very strong connections, not for mid
range.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The beacon timer drifts by 1 microsecond every TBTT. After 20 minutes
with a beacon interval of 100, the drift will be almost 12 ms, enough to
cause weird issues for devices in powersave mode.
Since the beacon timer is configured in units of 1/16 TU (64 us), we
need to adjust it once every 64 beacons and only for one beacon.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
I am removing the
BUG_ON(!in_interrupt());
check because it serves no purpose. Running the completion callback in
BH context makes in_interrupt() still return true but the interrupts
could be enabled. The important part is that ->driver_lock is acquired
with disabled interrupts which is the case now.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
I am removing the
BUG_ON(!in_interrupt());
check because it serves no purpose. Running the completion callback in
BH context makes in_interrupt() still return true but the interrupts
could be enabled. The important part is that ->driver_lock is acquired
with disabled interrupts which is the case now.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ipw2x00 driver family uses get_seconds() to read the current time
for various purposes. This function is deprecated because of the 32-bit
time_t overflow, and it can cause unexpected behavior when the time
changes due to settimeofday() calls or leap second updates.
In many cases, we want to use monotonic time instead, however ipw2x00
explicitly tracks the time spent in suspend, so this changes the
driver over to use ktime_get_boottime_seconds(), which is slightly
slower, but not used in a fastpath here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The get_seconds() function is deprecated because of the y2038 overflow.
In zd1211rw we don't even care about the absolute value, so this is
not a problem, but it's equally trivial to change to the non-deprecated
ktime_get_seconds().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The BIT macro uses unsigned long which some architectures handle as 32 bit
and therefore might cause macro's shift to overflow when used on a value
equals or larger than 32 (NL80211_STA_INFO_RX_DURATION and afterwards).
Since 'filled' member in station_info changed to u64, BIT_ULL macro
should be used with all NL80211_STA_INFO_* attribute types instead of BIT
to prevent future possible bugs when one will use BIT macro for higher
attributes by mistake.
This commit cleans up all usages of BIT macro with the above field
in wireless-drivers by changing it to BIT_ULL instead. In addition, there are
some places which don't use BIT nor BIT_ULL macros so align those as well.
Signed-off-by: Omer Efrat <omer.efrat@tandemg.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a static checker fix, not something I have tested. The issue
is that on the second iteration through the loop, we jump forward by
le32_to_cpu(auth_req->length) bytes. The problem is that if the length
is more than "buflen" then we end up with a negative "buflen". A
negative buflen is type promoted to a high positive value and the loop
continues but it's accessing beyond the end of the buffer.
I believe the "auth_req->length" comes from the firmware and if the
firmware is malicious or buggy, you're already toasted so the impact of
this bug is probably not very severe.
Fixes: 030645aceb ("rndis_wlan: handle 802.11 indications from device")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
use existing memdup_user() helper function instead of open-coding
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix mcs and attempt count estimation in mt76x2_mac_fill_tx_status routine
if the number of tx retries reported by the hw is grater than
IEEE80211_TX_MAX_RATES
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove extra parentheses and replace NULL comparison with !priv, to fix
clang warning of extraneous parentheses and check patch issue. Following
coccinelle script is used to fix it.
@disable is_null,paren@
expression e;
statement s;
@@
if (
- (e==NULL)
+!e
)
s
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not chock ethernet header for uap bridge data path,
as it is still needed to send skb to dest station.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function wlc_phy_workarounds_nphy_rev1 is local to the source and
does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'wlc_phy_workarounds_nphy_rev1' was not declared. Should it
be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The last value in the log_table wraps around to a negative value
since s16 has a value range of -32768 to 32767. This is not what
the table intends to represent. Use the closest positive value
32767.
This fixes a warning seen with clang:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/phy/phy_qmath.c:216:2: warning:
implicit conversion from 'int' to 's16' (aka 'short') changes
value from 32768
to -32768 [-Wconstant-conversion]
32768
^~~~~
1 warning generated.
Fixes: 4c0bfeaae9 ("brcmsmac: fix array out-of-bounds access in qm_log10")
Cc: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the clang warning of extraneous parentheses, with the
following coccinelle script.
@@
identifier i;
expression e;
statement s;
@@
if (
-(i == e)
+i == e
)
s
Suggested-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable support for source MAC address randomization of probe request
frames. Pass addr/mask randomization parameters to firmware.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement net_device_ops::ndo_set_mac_address callback to allow for
setting interface MAC address. Implementation is done through existing
CHANGE_INTF firmware command. All validation is to be done by firmware.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With runtime PM tested working for wlcore with no autosuspend, we can
now enable autosuspend to cut down on enable/disable for interrupts.
Basically we just replace pm_runtime_put() with the autosuspend variants.
Let's use autosuspend delay of 50ms that MMC drivers typically use.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We have wl12xx_boot() call wl12xx_enable_interrupts() and if we have
wl1271_op_add_interface() call pm_runtime_get_sync() before the interrupts
are enabled. And then we get the following error during boot:
wlcore: ERROR ELP wakeup timeout!
Let's fix this by first checking if we need to boot the firmware. And
only after that call pm_runtime_get_sync() when interrupts are enabled.
And only after that do the check for wl12xx_need_fw_change().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With runtime PM enabled, we can now use calls to pm_runtime_force_suspend
and pm_runtime_force_resume for enabling elp during suspend when wowlan
is enabled and waking the chip from elp on resume.
Remove the custom API that was used to ensure that the command
that is used to allow ELP during suspend is completed before the system
suspend.
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After enabling runtime PM, if we force hardware reset multiple times with:
# echo 1 > /sys/kernel/debug/ieee80211/phy0/wlcore/start_recovery
We will after few tries get the following error:
wlcore: ERROR timeout waiting for the hardware to complete initialization
And then wlcore is unable to reconnect until after the wlcore related modules
are reloaded.
Let's fix this by moving pm_runtime_put() earlier before we restart the hardware.
And let's use the sync version to make sure we're done before we restart.
Note that we still will get -EBUSY warning from wl12xx_sdio_set_power() but let's
fix that separately once we know exactly why we get the warning.
Reported-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With runtime PM enabled, we now need to have wlcore enabled longer
until after we're done calling wlcore_cmd_regdomain_config_locked():
scan_complete_work()
wlcore_cmd_regdomain_config_locked()
wlcore_cmd_send_failsafe()
wl12xx_sdio_raw_read()
Note that this is not needed before runtime PM support as the
custom PM code had it's own timer. We have not yet enabled runtime
PM autosuspend for wlcore and this is why this issue now shows up.
Let's fix the issues first before we enable runtime PM autosuspend.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We can update wlcore to use PM runtime by adding functions for
wlcore_runtime_suspend() and wlcore_runtime_resume() and replacing
calls to wl1271_ps_elp_wakeup() and wl1271_ps_elp_sleep() with calls
to pm_runtime_get_sync() and pm_runtime_put().
Note that the new wlcore_runtime_suspend() and wlcore_runtime_resume()
functions are based on simplified versions of wl1271_ps_elp_sleep() and
wl1271_ps_elp_wakeup().
We don't want to use the old functions as we can now take advantage of
the runtime PM usage count. And we don't need the old elp_work at all.
And we can also remove WL1271_FLAG_ELP_REQUESTED that is no longer needed.
Pretty much the only place where we are not just converting the existing
functions is wl1271_op_suspend() where we add pm_runtime_put_noidle()
to keep the calls paired.
As the next step is to implement runtime PM autosuspend, let's not add
wrapper functions for the generic runtime PM calls. We would be getting
rid of any wrapper functions anyways.
After autoidle we should be able to start using Linux generic wakeirqs
for the padconf interrupt.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The call to wl1271_ps_elp_wakeup() in wl12xx_queue_recovery_work() is
unpaired. Let's remove it and add paired calls to wl1271_recovery_work()
instead in preparation for changing things to use runtime PM.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Otherwise we can get:
WARNING: CPU: 0 PID: 55 at drivers/net/wireless/ti/wlcore/io.h:84
I've only seen this few times with the runtime PM patches enabled
so this one is probably not needed before that. This seems to
work currently based on the current PM implementation timer. Let's
apply this separately though in case others are hitting this issue.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Map read has been supported on NFP, this patch enables optimization
for memcpy from map to packet.
This patch also fixed one latent bug which will cause copying from
unexpected address once memcpy for map pointer enabled. The fixed
code path was not exercised before.
Reported-by: Mary Pham <mary.pham@netronome.com>
Reported-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
sizeof() will return unsigned value so in the error check
negative error code will be always larger than sizeof().
Fixes: a0d8e02c35 ("nfp: add support for reading nffw info")
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any error status returned by FW will trigger a print similar to the
following error message in the dmesg.
[ 55.884355] mlx5_core 0000:00:04.0: mlx5_cmd_check:712:(pid 555):
ALLOC_UAR(0x802) op_mod(0x0) failed, status limits exceeded(0x8),
syndrome (0x0)
Those prints are extremely valuable to diagnose issues with running system
and it is important to keep them. However, not-so-careful user can trigger
endless number of such prints by depleting HW resources and will spam
dmesg.
Rate limiting of such messages solves this issue.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
TC shared blocks allow multiple qdiscs to be grouped together and filters
shared between them. Currently the chains of filters attached to a block
are only flushed when the block is removed. If a qdisc is removed from a
block but the block still exists, flow del messages are not passed to the
callback registered for that qdisc. For the NFP, this presents the
possibility of rules still existing in hw when they should be removed.
Prevent binding to shared blocks until the kernel can send per qdisc del
messages when block unbinds occur.
tcf_block_shared() was not used outside of the core until now, so also
add an empty implementation for builds with CONFIG_NET_CLS=n.
Fixes: 4861738775 ("net: sched: introduce shared filter blocks infrastructure")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously it was not possible to distinguish between mpls ether types and
other ether types. This leads to incorrect classification of offloaded
filters that match on mpls ether type. For example the following two
filters overlap:
# tc filter add dev eth0 parent ffff: \
protocol 0x8847 flower \
action mirred egress redirect dev eth1
# tc filter add dev eth0 parent ffff: \
protocol 0x0800 flower \
action mirred egress redirect dev eth2
The driver now correctly includes the mac_mpls layer where HW stores mpls
fields, when it detects an mpls ether type. It also sets the MPLS_Q bit to
indicate that the filter should match mpls packets.
Fixes: bb055c198d ("nfp: add mpls match offloading support")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The command interface can work in two modes: Events and Polling.
In the general case, each time we invoke a command, a work is
queued to handle it.
When working in events, the interrupt handler completes the
command execution. On the other hand, when working in polling
mode, the work itself completes it.
Due to a bug in the work handler, a command could have been
completed by the interrupt handler, while the work handler
hasn't finished yet, causing the it to complete once again
if the command interface mode was changed from Events to
polling after the interrupt handler was called.
mlx5_unload_one()
mlx5_stop_eqs()
// Destroy the EQ before cmd EQ
...cmd_work_handler()
write_doorbell()
--> EVENT_TYPE_CMD
mlx5_cmd_comp_handler() // First free
free_ent(cmd, ent->idx)
complete(&ent->done)
<-- mlx5_stop_eqs //cmd was complete
// move to polling before destroying the last cmd EQ
mlx5_cmd_use_polling()
cmd->mode = POLL;
--> cmd_work_handler (continues)
if (cmd->mode == POLL)
mlx5_cmd_comp_handler() // Double free
The solution is to store the cmd->mode before writing the doorbell.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The NULL character was not set correctly for the string containing
the command length, this caused failures reading the output of the
command due to a random length. The fix is to initialize the output
length string.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Manipulating of the MPFS requires eswitch manager capabilities.
Fixes: eeb66cdb68 ('net/mlx5: Separate between E-Switch and MPFS')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In smartnic env, if the host (PF) driver is not an e-switch manager, we
are not allowed to apply eswitch ports setups such as vlan (VST),
spoof-checks, min/max rate or state.
Make sure we are eswitch manager when coming to issue these callbacks
and err otherwise.
Also fix the definition of ESW_ALLOWED to rely on eswitch_manager
capability and on the vport_group_manger.
Operations on the VF nic vport context, such as setting a mac or reading
the vport counters are allowed to the PF in this scheme.
The modify nic vport guid code was modified to omit checking the
nic_vport_node_guid_modify eswitch capability.
The reason for doing so is that modifying node guid requires vport group
manager capability, and there's no need to check further capabilities.
1. set_vf_vlan - disallowed
2. set_vf_spoofchk - disallowed
3. set_vf_mac - allowed
4. get_vf_config - allowed
5. set_vf_trust - disallowed
6. set_vf_rate - disallowed
7. get_vf_stat - allowed
8. set_vf_link_state - disallowed
Fixes: f942380c12 ('net/mlx5: E-Switch, Vport ingress/egress ACLs rules for spoofchk')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Tested-by: Or Gerlitz <ogerlitz@mellanox.com>
In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the switchdev mode representors are running on
the embedded cpu (EC) and not at the host.
As such, we should avoid dealing with vport representors if
not being esw manager.
While here, make sure to disallow eswitch switchdev related
setups through devlink if we are not esw managers.
Fixes: cb67b83292 ('net/mlx5e: Introduce SRIOV VF representors')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In smartnic env, the host (PF) driver might not be an e-switch
manager, hence the FW will err on driver attempts to deal with
setting/unsetting the eswitch and as a result the overall setup
of sriov will fail.
Fix that by avoiding the operation if e-switch management is not
allowed for this driver instance. While here, move to use the
correct name for the esw manager capability name.
Fixes: 81848731ff ('net/mlx5: E-Switch, Add SR-IOV (FDB) support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Guy Kushnir <guyk@mellanox.com>
Reviewed-by: Eli Cohen <eli@melloanox.com>
Tested-by: Eli Cohen <eli@melloanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The check for cpu hit statistics was not returning immediate false for
any non vport rep netdev and hence we crashed (say on mlx5 probed VFs) if
user-space tool was calling into any possible netdev in the system.
Fix that by doing a proper check before dereferencing.
Fixes: 1d447a3914 ('net/mlx5e: Extendable vport representor netdev private data')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Eli Cohen <eli@melloanox.com>
Reviewed-by: Eli Cohen <eli@melloanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
