Memory size is limited in the kdump kernel environment. Allocation of more
msix-vectors (or queues) consumes few tens of MBs of memory, which might
lead to the kdump kernel failure.
This patch adds changes to limit the number of MSI-X vectors in kdump
kernel to minimum required value (i.e., 2 per engine).
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After we change the ipvlan mode from l3 to l2, or vice versa, we only
reset IFF_NOARP flag, but don't flush the ARP table cache, which will
cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2().
Then the message will not come out of host.
Here is the reproducer on local host:
ip link set eth1 up
ip addr add 192.168.1.1/24 dev eth1
ip link add link eth1 ipvlan1 type ipvlan mode l3
ip netns add net1
ip link set ipvlan1 netns net1
ip netns exec net1 ip link set ipvlan1 up
ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1
ip route add 192.168.2.0/24 via 192.168.1.2
ping 192.168.2.2 -c 2
ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2
ping 192.168.2.2 -c 2
Add the same configuration on remote host. After we set the mode to l2,
we could find that the src/dst MAC addresses are the same on eth1:
21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84)
192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64
Fix this by calling dev_change_flags(), which will call netdevice notifier
with flag change info.
v2:
a) As pointed out by Wang Cong, check return value for dev_change_flags() when
change dev flags.
b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops.
So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path.
Reported-by: Jianlin Shi <jishi@redhat.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Fixes: 2ad7bf3638 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if sa_idx is equal to NSIM_IPSEC_MAX_SA_COUNT then
an out-of-bounds read on ipsec->sa will occur. Fix the
incorrect bounds check by using >= rather than >.
Detected by CoverityScan, CID#1470226 ("Out-of-bounds-read")
Fixes: 7699353da8 ("netdevsim: add ipsec offload testing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the addition of GRO for ESP, gro_receive can consume the skb and
return -EINPROGRESS. In that case, the lower layer GRO handler cannot
touch the skb anymore.
Commit 5f114163f2 ("net: Add a skb_gro_flush_final helper.") converted
some of the gro_receive handlers that can lead to ESP's gro_receive so
that they wouldn't access the skb when -EINPROGRESS is returned, but
missed other spots, mainly in tunneling protocols.
This patch finishes the conversion to using skb_gro_flush_final(), and
adds a new helper, skb_gro_flush_final_remcsum(), used in VXLAN and
GUE.
Fixes: 5f114163f2 ("net: Add a skb_gro_flush_final helper.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-07-01
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) A bpf_fib_lookup() helper fix to change the API before freeze to
return an encoding of the FIB lookup result and return the nexthop
device index in the params struct (instead of device index as return
code that we had before), from David.
2) Various BPF JIT fixes to address syzkaller fallout, that is, do not
reject progs when set_memory_*() fails since it could still be RO.
Also arm32 JIT was not using bpf_jit_binary_lock_ro() API which was
an issue, and a memory leak in s390 JIT found during review, from
Daniel.
3) Multiple fixes for sockmap/hash to address most of the syzkaller
triggered bugs. Usage with IPv6 was crashing, a GPF in bpf_tcp_close(),
a missing sock_map_release() routine to hook up to callbacks, and a
fix for an omitted bucket lock in sock_close(), from John.
4) Two bpftool fixes to remove duplicated error message on program load,
and another one to close the libbpf object after program load. One
additional fix for nfp driver's BPF offload to avoid stopping offload
completely if replace of program failed, from Jakub.
5) Couple of BPF selftest fixes that bail out in some of the test
scripts if the user does not have the right privileges, from Jeffrin.
6) Fixes in test_bpf for s390 when CONFIG_BPF_JIT_ALWAYS_ON is set
where we need to set the flag that some of the test cases are expected
to fail, from Kleber.
7) Fix to detangle BPF_LIRC_MODE2 dependency from CONFIG_CGROUP_BPF
since it has no relation to it and lirc2 users often have configs
without cgroups enabled and thus would not be able to use it, from Sean.
8) Fix a selftest failure in sockmap by removing a useless setrlimit()
call that would set a too low limit where at the same time we are
already including bpf_rlimit.h that does the job, from Yonghong.
9) Fix BPF selftest config with missing missing NET_SCHED, from Anders.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the NFP fw only supports L3/L4 hashing so rejects the offload of
filters that output to LAG ports implementing other hash algorithms. Team,
however, uses a BPF function for the hash that is not defined. To support
Team offload, accept hashes that are defined as 'unknown' (only Team
defines such hash types). In this case, use the NFP default of L3/L4
hashing for egress port selection.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the tos and the tunnel flags from the tunnel key and offload these
action fields. Only the checksum and tunnel key flags are implemented in
fw so reject offloads of other flags. The tunnel key flag is always
considered set in the fw so enforce that it is set in the rule. Note that
the compulsory setting of the tunnel key flag and optional setting of
checksum is inline with how tc currently generates ipv4 udp tunnel
actions.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the ttl for ipv4 udp tunnels was set to the namespace default.
Modify this to attempt to extract the ttl from a full route lookup on the
tunnel destination. If this is not possible then resort to the default.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We used to leave bus-info in ethtool driver info empty for
representors in case multi-PCIe-to-single-host cards make
the association between PCIe device and NFP many to one.
It seems these attempts are futile, we need to link the
representors to one PCIe device in sysfs to get consistent
naming, plus devlink uses one PCIe as a handle, anyway.
The multi-PCIe-to-single-system support won't be clean,
if it ever comes.
Turns out some user space (RHEL tests) likes to read bus-info
so just populate it.
While at it remove unnecessary app NULL-check, representors
are spawned by an app, so it must exist.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_consume_skb() in nfp_net_tx_complete() to get bulk free.
Pass 0 as budget for ctrl queue completion since it runs out of
a tasklet.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP NAPI handling will only complete the TXed packets when called
with budget of 0, implement ndo_poll_controller by scheduling NAPI
on all TX queues.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms with broken ACPI tables we may not have access
to the Serial Number PCIe capability. This capability is crucial
for us for switchdev operation as we use serial number as switch ID,
and for communication with management FW where interface ID is used.
If we can't determine the Serial Number we have to fail device probe.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After user changes the ring count statistics for deactivated
rings disappear from ethtool -S output. This causes loss of
information to the user and means that ethtool stats may not
add up to interface stats. Always expose counters from all
the rings. Note that we allocate at most num_possible_cpus()
rings so number of rings should be reasonable.
The alternative of only listing stats for rings which were
ever in use could be confusing.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing device hotplug the sub channel must be async to avoid
deadlock issues because device is discovered in softirq context.
When doing changes to MTU and number of channels, the setup
must be synchronous to avoid races such as when MTU and device
settings are done in a single ip command.
Reported-by: Thomas Walker <Thomas.Walker@twosigma.com>
Fixes: 8195b1396e ("hv_netvsc: fix deadlock on hotplug")
Fixes: 732e49850c ("netvsc: fix race on sub channel creation")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __alx_open function can be called from ndo_open, which is called
under RTNL, or from alx_resume, which isn't. Since commit d768319cd4,
we're calling the netif_set_real_num_{tx,rx}_queues functions, which
need to be called under RTNL.
This is similar to commit 0c2cc02e57 ("igb: Move the calls to set the
Tx and Rx queues into igb_open").
Fixes: d768319cd4 ("alx: enable multiple tx queues")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug where INT_STAT1 was written twice and
INT_STAT2 was ignored when disabling interrupts.
Fixes: b753a9faaf ("net: phy: DP83TC811: Introduce support for the DP83TC811 phy")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small merge conflict in net/mac80211/scan.c, I preserved
the kcalloc() conversion. -DaveM
Johannes Berg says:
====================
This round's updates:
* finally some of the promised HE code, but it turns
out to be small - but everything kept changing, so
one part I did in the driver was >30 patches for
what was ultimately <200 lines of code ... similar
here for this code.
* improved scan privacy support - can now specify scan
flags for randomizing the sequence number as well as
reducing the probe request element content
* rfkill cleanups
* a timekeeping cleanup from Arnd
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The very first version of RTL8169 from 2002 (and only this one) has
support for a TBI 1000BaseX fiber interface. The TBI support in the
driver makes switching to phylib tricky, so best would be to get
rid of it. I found no report from anybody using a device with RTL8169
and fiber interface, also the vendor driver doesn't support this mode
(any longer).
So remove TBI support and bail out with a message if a card with
activated TBI is detected. If there really should be any user of it
out there, we could add a stripped-down version of the driver
supporting chip version 01 and TBI only (and maybe move it to
staging).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation of adding phylib support to the r8169 driver we need
PHY drivers for all chip-internal PHY types. Fortunately almost all
of them are either supported by the Realtek PHY driver already or work
with the genphy driver.
Still missing is support for the PHY of RTL8169s, it requires a quirk
to properly support 100Mbit-fixed mode. The quirk was copied from
r8169 driver which copied it from the vendor driver.
Based on the PHYID the internal PHY seems to be a RTL8211.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I see no need to define a private debug output symbol, let's use the
standard debug output functions instead. In this context also remove
the deprecated PFX define.
The one assertion is wrong IMO anyway, this code path is used also
by chip version 01.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes below checkpatch checks-
CHECK: spaces preferred around that '*' (ctx:VxV)
CHECK: No space is necessary after a cast
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes below checkpatch warnings-
WARNING: Block comments use a trailing */ on a separate line
WARNING: Block comments use * on subsequent lines
WARNING: networking block comments don't use an empty /* line,
use /* Comment
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes below kernel-doc warnings:
Function parameter or member 'maxlen' not described in 'xemaclite_recv_data'
Function parameter or member 'address'not described in 'xemaclite_set_mac_address'
Excess function parameter 'addr' description in 'xemaclite_set_mac_address'
No description found for return value of 'xemaclite_interrupt'
No description found for return value of 'xemaclite_mdio_write'
Function parameter or member 'dev' not described in 'xemaclite_mdio_setup'
Excess function parameter 'ofdev' description in 'xemaclite_mdio_setup'
No description found for return value of 'xemaclite_open'
No description found for return value of 'xemaclite_close'
Excess function parameter 'match' description in 'xemaclite_of_probe'
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove else as it is not required with if doing a return.
It also coalesce the format onto a single line and add the
missing space after the comma. Fixes below checkpatch warning-
WARNING: else is not generally useful after a break or return
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch hardcoded function name with a reference to __func__ making
the code more maintainable. Address below checkpatch warning:
WARNING: Prefer using '"%s...", __func__' to using 'xemaclite_mdio_read',
this function's name, in a string
+ "xemaclite_mdio_read(phy_id=%i, reg=%x) == %x\n",
WARNING: Prefer using '"%s...", __func__' to using 'xemaclite_mdio_write',
this function's name, in a string
+ "xemaclite_mdio_write(phy_id=%i, reg=%x, val=%x)\n",
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking the skb->protocol field, we have to make sure we use the
proper endianness using htons, and not swab16.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlan IDs must not be swapped when creating Header Parser entries. This
has no effect on little-endian systems, but is wrong for big-endian.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPv2's Header Parser use some large TCAM and SRAM entries, that are
duplicated in software so that we can write them to hardware only when
we are done modifying them.
Currently, PPv2 uses a union containing arrays of u32 and u8 to represent
these entries, to facilitate byte per byte access. This representation is
broken when we want to support big endian, and this makes the code
confusing to read.
This patch drops the union, and simply stores the TCAM and SRAM entries
as u32 arrays, each entry corresponding to a 32-bit register.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2 controller always expect descriptors to be in little endian. We
must therefore force descriptors to use that format, and convert to the
host endianness when necessary.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DPAA HW requires that at least 256 bytes from the start of the
first scatter-gather table entry are allocated and accessible. The
hardware reads the maximum size the table can have in one access,
thus requiring that the allocation and mapping to be done for the
maximum size of 256B even if there is a smaller number of entries
in the table.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FMan hardware parser needs to be configured to remove the
short frame padding from the checksum calculation, otherwise
short UDP and TCP frames are likely to be marked as having a
bad checksum.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver performs the internal reload when it receives tx-timeout event from
the OS. Internal reload might fail in some scenarios e.g., fatal HW issues.
In such cases OS still see the link, which would result in undesirable
functionalities such as re-generation of tx-timeouts.
The patch addresses this issue by indicating the link-down to OS when
tx-timeout is detected, and keeping the link in down state till the
internal reload is successful.
Please consider applying it to 'net' branch.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static checkers complain that id_tbl->table points to longs and 4 bytes
is smaller than sizeof(long). But the since other side is dividing by
32 instead of sizeof(long), that means the current code works fine.
Anyway, it's more conventional to use the BITS_TO_LONGS() macro when
we're allocating a bitmap.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before 8d85a7a4f2 ("PCI/IOV: Allow PF drivers to limit total_VFs to 0"),
pci_sriov_set_totalvfs(pdev, 0) meant "we can enable TotalVFs virtual
functions". After 8d85a7a4f2, it means "we can't enable *any* VFs".
That broke this scenario where nfp intends to remove any limit on the
number of VFs that can be enabled:
nfp_pci_probe
nfp_pcie_sriov_read_nfd_limit
nfp_rtsym_read_le("nfd_vf_cfg_max_vfs", &err)
pci_sriov_set_totalvfs(pf->pdev, 0) # if FW didn't expose a limit
...
# userspace writes N to sysfs "sriov_numvfs":
sriov_numvfs_store
pci_sriov_get_totalvfs # now returns 0
return -ERANGE
Prior to 8d85a7a4f2, pci_sriov_get_totalvfs() returned TotalVFs, but it
now returns 0.
Remove the pci_sriov_set_totalvfs(pdev, 0) calls so we don't limit the
number of VFs that can be enabled.
Fixes: 8d85a7a4f2 ("PCI/IOV: Allow PF drivers to limit total_VFs to 0")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Saeed Mahameed says:
====================
mlx5e-updates-2018-06-28
mlx5e netdevice driver updates:
- Boris Pismenny added the support for UDP GSO in the first two patches.
Impressive performance numbers are included in the commit message,
@Line rate with ~half of the cpu utilization compared to non offload
or no GSO at all.
- From Tariq Toukan:
- Convert large order kzalloc allocations to kvzalloc.
- Added performance diagnostic statistics to several places in data path.
From Saeed and Eran,
- Update NIC HW stats on demand only, this is to eliminate the background
thread needed to update some HW statistics in the driver cache in
order to report error and drop counters from HW in ndo_get_stats.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the tunnel option type stored in tunnel flags when creating options
for tunnels. Thereby ensuring we do not set geneve, vxlan or erspan tunnel
options on interfaces that are not associated with them.
Make sure all users of the infrastructure set correct flags, for the BPF
helper we have to set all bits to keep backward compatibility.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The present TX workrequest(FW_ETH_TX_PKT_WR) cant be used for
host->vf communication, since it doesn't loopback the outgoing
packets to virtual interfaces on the same port. This can be done
using FW_ETH_TX_PKT_VM_WR.
This fix depends on ethtool_flags to determine what WR to use for
TX path. Support for setting this flags by user is added in next
commit.
Based on the original work by : Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add constants and callback functions for the dwmac on px30 Soc.
The base structure is the same, but registers and the bits in
them are moved slightly, and add the clk_mac_speed for selecting
mac speed.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of WEP encryption, driver has to configure shared key for
associated station(s). Note that sta pointer is NULL in case of non
pairwise key, causing NULL pointer dereference with existing code
(sta_priv->is_data_encrypted). Fix this by using associated sta list
instead. This enables WEP support as client, WEP AP is non-functional.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The USB completion callback does not disable interrupts while acquiring
the lock. We want to remove the local_irq_disable() invocation from
__usb_hcd_giveback_urb() and therefore it is required for the callback
handler to disable the interrupts while acquiring the lock.
The callback may be invoked either in IRQ or BH context depending on the
USB host controller.
Use the _irqsave() variant of the locking primitives.
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
