Fix mt76x2_temp_tx_alc_enabled routine since in order to enable tx_alc
temperature compensation it necessary to take into account BIT(15) of
MT_EE_TX_POWER_EXT_PA_5G eeprom info
Fixes: 7bc04215a6 ("mt76: add driver code for MT76x2e")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove unnecessary MT_TX_ALC_CFG_4 configuration since the register value
will be properly set according to the usage of an external power amplifier
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not attempt to reorder packets not part of a BA session
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Required for fast-rx and allows mac80211 to skip an unnnecessary check.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use cancel_delayed_work instead of cancel_delayed_work_sync
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There were a number of issues in the existing tx power handling code:
1. The EEPROM target power for chain 0 refers to the actual output power
after the channel and bandwidth delta have been added to the initial
channel gain. This means the delta values should not be added/subtracted
for the rate power calculation
2. When power is reduced significantly, the initial channel gain
underflows very quickly, while the per-rate power offsets are high.
This miscalculation causes effective tx power to be increased when it
should actually be lowered.
Fix this by trying to adjust the channel gain to the lowest power from
the rate table. In case of under- or overflow, compensate by adding an
appropriate delta to the rate power values.
This makes power configuration more accurate on a wider range of
configurable values
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoids race conditions from mac80211 enqueueing tx packets before the
tx-drop bit is cleared
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Allows the driver to control whether to send a BlockAckReq after waking
up. MT76x2 needs this set to true, for MT7603 (to be submitted later)
it needs to be false.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add static qualifier to mt76x2_mac_reset routine and remove the
prototype from mt76x2_mac.h since it is used just in mt76x2_init.c
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the statements are identical, we can safely remove the statements.
The commit 42e74946f0 ("rtlwifi: btcoexist: Fix if == else warnings in
halbtc8821a1ant.c") had fixed the statements, but the commit c6821613e6
("rtlwifi: btcoex: follow linux coding style") that converted coding style
and upgraded btcoex didn't include the fix.
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently TID is extracted by checking at specific offset in data frame.
This approach doesn't work for some of the frames. This patch uses mac80211
API and do it correctly
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Power save request should be sent on station interface. Virtual
interface which is connected should be preferred. This patch
resolves device not entering power save problem in certain
situations
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The issue here is that we allocate "data" and then set
"data = PTR_ALIGN(data, 8);" and then we free the aligned pointer
instead of the original pointer.
kmalloc() pointers are already ARCH_SLAB_MINALIGN aligned which is 8 or
more on everything except certain Xtensa variants. We decided that if
the Xtensa people ever notice a bug here then we'll tell them the bug is
on their side. ;)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To support roaming below changes are done:
* Station notify frame is send to firmware after sending assoc
request. This will avoid dropping of first EAPOL frame due to
delay in creation of station control block in firmware.
* Data queues are unblocked after sending station notify in open
mode, after configuring key in WEP mode, and after receiving
EAPOL4 confirm in WPA mode.
* Initial EAPOL frames priority is chaged to MGMT, rekey EAPOL
frames priority changed to VO.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All descriptor structures are in rsi_mgmt.h except this
extended descriptor structure. Hence moving it to rsi_mgmt.h
and also renaming to rsi_xtend_desc.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Amitkumar Karwar <amit.karwar@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DFS offload support implemented:
- DFS_OFFLOAD feature is advertised depending on HW capabilities
- CAC_STARTED event forwarding from HW implemented
- start_radar_detection() callback now returning -ENOTSUPP
if DFS_OFFLOAD is enabled
Signed-off-by: Dmitry Lebed <dlebed@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some HP laptops have only a single wifi antenna. This would not be a
problem except that they were shipped with an incorrectly encoded
EFUSE. It should have been possible to open the computer and transfer
the antenna connection to the other terminal except that such action
might void the warranty, and moving the antenna broke the Windows
driver. The fix was to add a module option that would override the
EFUSE encoding. That was done with commit c18d8f5095 ("rtlwifi:
rtl8723be: Add antenna select module parameter"). There was still a
problem with Bluetooth coexistence, which was addressed with commit
baa1702290 ("rtlwifi: btcoexist: Implement antenna selection").
There were still problems, thus there were commit 0ff78adeef
("rtlwifi: rtl8723be: fix ant_sel code") and commit 6d62269283
("rtlwifi: btcoexist: Fix antenna selection code"). Despite all these
attempts at fixing the problem, the code is not yet right. A proper
fix is important as there are now instances of laptops having
RTL8723DE chips with the same problem.
The module parameter ant_sel is used to control antenna number and path.
At present enum ANT_{X2,X1} is used to define the antenna number, but
this choice is not intuitive, thus change to a new enum ANT_{MAIN,AUX}
to make it more readable. This change showed examples where incorrect
values were used. It was also possible to remove a workaround in
halbtcoutsrc.c.
The experimental results with single antenna connected to specific path
are now as follows:
ant_sel ANT_MAIN(#1) ANT_AUX(#2)
0 -8 -62
1 -62 -10
2 -6 -60
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Fixes: c18d8f5095 ("rtlwifi: rtl8723be: Add antenna select module parameter")
Fixes: baa1702290 ("rtlwifi: btcoexist: Implement antenna selection")
Fixes: 0ff78adeef ("rtlwifi: rtl8723be: fix ant_sel code")
Fixes: 6d62269283 ("rtlwifi: btcoexist: Fix antenna selection code")
Cc: Stable <stable@vger.kernel.org> # 4.7+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When version 8 of the scan command API was introduced, only the size
of version 7 was updated, causing older versions of the firmware to
throw BAD_COMMAND errors.
Calculating the old version based on the size of the latest version
got too complicated and the size of the older versions will never
change anyway, so it's better to just hardcoded the sizes.
Fixes: 66fa2424df ("iwlwifi: fw api: support the new scan request FW API version")
Reported-by: Scott Register <sreg@sreg.io>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the wifi driver core passes IE elements in the scan request, append
them to the firmware message. The driver currently tells the core that
it is capable of attaching up to WCN36XX_MAX_SCAN_IE_LEN octets, but
doesn't actually pass them to the the hardware.
Note that this patch doesn't fix a bug that was observed. The change is
merely done for the sake of completeness as the hardware supports
appending IEs in scans. Tests show that network scans work fine with
this patch applied.
Some defines were moved around to avoid cyclic include dependencies.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pass the bss_type of the currently configured BSS in the message for the
scan request. Therefore, that setting needs to be kept in struct
wcn36xx_vif.
This seems to be only interesting when scanning for a specific SSID
and doesn't matter for regular wildcard scans.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For firmwares that don't have the SCAN_OFFLOAD feature bit set, do
not call into wcn36xx_smd_stop_hw_scan(). Instead, stop the asynchronous
work and call into ieee80211_scan_completed() immediately.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the network interface goes down while a scan request is still
pending that can't be stopped due to firmware hickups, wcn->scan_req
remains set, even though the hardware is deinitialized. This results
in -EBUSY for all scan requests after the interface was brought up
again.
Fix this by explicitly completing pending scan requests in
wcn36xx_stop().
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the firmware sends a WCN36XX_HAL_SCAN_IND_DEQUEUED indication,
the request is apparently no longer valid. Attempts to stop the hardware
scan request subsequently will lead to the following error message, and
the hardware is no longer able to communicate with any AP:
[ 57.917186] wcn36xx: ERROR hal_stop_scan_offload response failed err=5
Interpreting this indicator message as scan abortion fixes this.
While at it, add a newline to a debug print.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable sta power save in fw for the targets that
supports idle power save. The idle ps enable command
will be ignored by the firmware which does not support
this feature.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SRRI/DRRI are not mapped in the HW Shadow block and can lead
to un-clocked access if common subsystem in the target is
powered down due to idle mode.
To mitigate this problem SRRI/DRRI can be read from
DDR instead of doing an actual hardware read.
Host allocates non cached memory on ddr and configures
the physical address of this memory to the CE hardware.
The hardware updates the RRI on this particular location.
Read SRRI/DRRI from DDR location instead of
direct target read.
Enable retention restore on ddr using hw params to enable
in specific targets.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 needs shadow register write operation support
for copy engine for regular operation in powersave mode.
Add support for copy engine shadow register write in
datapath tx for WCN3990
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn3990 supports shadow register for ce write.
Add a hw param for shadow register support.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By default ath10k driver enables the support for HW_CHECKSUM
(NETIF_F_HW_CSUM). Since the TCP/UDP checksum calculation is not enabled
in the wcn3990 firmware the checksum is incorrect in the TCP/UDP packets
and all patckets are dropped. But due note that wcn3990 support in
ath10k is still incomplete so this isn't a critical fix (yet).
Enable hw checksum calculations in wcn3990 hardware by
setting the proper flags in msdu descriptor tso flags.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware message to delete BSS keys expects a BSS index to be passed.
This field is currently hard-coded to 0. Fix this by passing in the index
we received from the firmware when the BSS was configured.
The encryption type in that message also needs to be set to what was used
when the key was set, so the assignment of vif_priv->encrypt_type is now
done after the firmware command was sent. This reportedly fixes the
following error in AP mode:
wcn36xx: ERROR hal_remove_bsskey response failed err=6
Also, AFAIU, when a BSS is deleted, the firmware apparently drops all the
keys associated with it. Trying to remove the key explicitly afterwards
will hence lead to the following message:
wcn36xx: ERROR hal_remove_bsskey response failed err=16
This is now suppressed with an extra check for the BSS index validity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When trying to set wow wakeup patterns it fails with this command:
iw phyxx wowlan enable patterns offset xx+ IP address xx.xx.xx.xx
The reason is that the wow pattern from upper layer is in 802.3 format
for this case, it need to convert it to 802.11 format. The input
offset parameter is used for 802.3, but the actual offset firmware
need depends on rx_decap_mode, so that it needs to be recalculated.
Pattern of 802.3 packet is not same with 802.11 packet. If the
rx_decap_mode is ATH10K_HW_TXRX_NATIVE_WIFI, then firmware will
receive data packet with 802.11 format from hardware.
Tested with QCA6174 hw3.0 with firmware
WLAN.RM.4.4.1-00099-QCARMSWPZ-1, but this will also affect QCA9377.
This has always failed, so it's not a regression with new firmware
releases.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ath10k reports the random_mac_addr capability to upper layer
based on the service bit firmware reported. Driver sets the
spoofed flag in scan_ctrl_flag to firmware if upper layer has
enabled this feature in scan request.
Test with QCA6174 hw3.0 and firmware-6.bin_WLAN.RM.4.4.1-00102-QCARMSWP-1,
but QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add WMI_SERVICE_AVAILABLE_EVENT to extend WMI_SERVICE_READY_EVENT,
the 128bit service map in WMI_SERVICE_READY_EVENT is not enough
for firmware to notice new WLAN service to host driver. Hereby,
for thoese new WLAN service, firmware will notice host driver by
WMI_SERVICE_AVAILABLE_EVENT.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When trying to open aggregations on 22000 HW before
traffic had actually passed, the driver will discover
it is missing a queue to aggregate on. In such a case -
allocate a queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's already an opmode common file for nvm iwl-nvm-parse.c
Move the content of fw/nvm.c to iwl-nvm-parse.c and delete fw/nvm.c.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The sku_capa_band_24GHz_enable and sku_capa_band_52GHz_enable symbols
cause checkpatch to complain whenever we use them. To prevent this,
convert them to all lower case.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of having a boolean for each modifier we need to handle in the
channel maps, create a bitmask with flags that denote each
modification.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
