Add FCPF and FCPV instances to the r8a774a1 dtsi, similarly
to what was done for the r8a7796 with commit 41dbbf0c5b
("arm64: dts: r8a7796: Add FCPF and FCPV instances"),
commit 69490bc966 ("arm64: dts: renesas: r8a7796: Point
FDP1 via FCPF to IPMMU-VI0"), and commit cef942d0bd ("arm64:
dts: renesas: r8a7796: Point VSPI via FCPVI to IPMMU-VC0").
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds definitions for L2 cache for the Cortex-A53 CPU
cores (512 KiB in size, organized as 32 KiB x 16 ways), adds
Cortex-A53 CPU cores (setting a total of 6 cores, 2 x Cortex-A57
+ 4 x Cortex-A53), and finally enables the performance monitor
unit for the Cortex-A53 cores on the R8A774A1 SoC.
Based on work done for r8a7796 SoC.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device nodes for all RZ/G2M SCIF and HSCIF serial ports,
incl. clocks, power domains and DMAs.
According to the HW user manual, SCIF[015] and HSCIF[012] are
connected to both SYS-DMAC1 and SYS-DMAC2, while SCIF[34] and
HSCIF[34] are connected to SYS-DMAC0.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to R-Car Gen3 HW manual rev1.00, R-Car M3-N has two CAN
interfaces, similar to H3, M3-W and other SoCs from the same family.
Add CAN placeholder nodes to avoid below DTC errors:
Error: arch/arm64/boot/dts/renesas/ulcb-kf.dtsi:19.1-6 Label or path can0 not found
Error: arch/arm64/boot/dts/renesas/ulcb-kf.dtsi:25.1-6 Label or path can1 not found
These errors occur *after* the addition of r8a77965-m3nulcb-kf.dts.
Fix them beforehand.
CAN support is inspired from below commits:
- v4.7 commit 308b7e4ba6 ("arm64: dts: r8a7795: Add CAN support")
- v4.11 commit 909c162524 ("arm64: dts: r8a7796: Add CAN support")
- v4.12 commit bec0948e81 ("arm64: dts: r8a7796: Add reset control properties")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
[simon: make placeholder minimal by only including reg property]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
For R-Car M3-N hook up SYS-DMAC0, SYS-DMAC1 and SYS-DMAC2 to
IPMMU-DS0 and IPMMU-DS1 in same way as for R-Car M3-W.
This follows the R-Car Gen3 Rev.1.00 (April 2018) datasheet.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the PDM input device on the S400 and it to the sound card
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There are 7 digital mics on the MIC daughter board attached
to the s400 board, so add the digital microphone codec to
its DTS
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
DMC is a small memory region with various registers,
including the ones needed for the canvas module.
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
There is actually several different libretech board with the CC suffix
so the model name is not appropriate here. Update to something more
specific
Reported-by: Da Xue <da@lessconfused.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Devices using the new V4L2 mem2mem vdec require a larger CMA pool. As
nearly all GX* devices are video/media focused and will use it, set a
larger (256MB) default value.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Sort DT nodes by address when possible, by node node name otherwise.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Pull networking fixes from David Miller:
1) Fix up several Kconfig dependencies in netfilter, from Martin Willi
and Florian Westphal.
2) Memory leak in be2net driver, from Petr Oros.
3) Memory leak in E-Switch handling of mlx5 driver, from Raed Salem.
4) mlx5_attach_interface needs to check for errors, from Huy Nguyen.
5) tipc_release() needs to orphan the sock, from Cong Wang.
6) Need to program TxConfig register after TX/RX is enabled in r8169
driver, not beforehand, from Maciej S. Szmigiero.
7) Handle 64K PAGE_SIZE properly in ena driver, from Netanel Belgazal.
8) Fix crash regression in ip_do_fragment(), from Taehee Yoo.
9) syzbot can create conditions where kernel log is flooded with
synflood warnings due to creation of many listening sockets, fix
that. From Willem de Bruijn.
10) Fix RCU issues in rds socket layer, from Cong Wang.
11) Fix vlan matching in nfp driver, from Pieter Jansen van Vuuren.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
nfp: flower: reject tunnel encap with ipv6 outer headers for offloading
nfp: flower: fix vlan match by checking both vlan id and vlan pcp
tipc: check return value of __tipc_dump_start()
s390/qeth: don't dump past end of unknown HW header
s390/qeth: use vzalloc for QUERY OAT buffer
s390/qeth: switch on SG by default for IQD devices
s390/qeth: indicate error when netdev allocation fails
rds: fix two RCU related problems
r8169: Clear RTL_FLAG_TASK_*_PENDING when clearing RTL_FLAG_TASK_ENABLED
erspan: fix error handling for erspan tunnel
erspan: return PACKET_REJECT when the appropriate tunnel is not found
tcp: rate limit synflood warnings further
MIPS: lantiq: dma: add dev pointer
netfilter: xt_hashlimit: use s->file instead of s->private
netfilter: nfnetlink_queue: Solve the NFQUEUE/conntrack clash for NF_REPEAT
netfilter: cttimeout: ctnl_timeout_find_get() returns incorrect pointer to type
netfilter: conntrack: timeout interface depend on CONFIG_NF_CONNTRACK_TIMEOUT
netfilter: conntrack: reset tcp maxwin on re-register
qmi_wwan: Support dynamic config on Quectel EP06
ethernet: renesas: convert to SPDX identifiers
...
Commit eeb89e2bb1 ("x86/efi: Load fixmap GDT in efi_call_phys_epilog()")
moved loading the fixmap in efi_call_phys_epilog() after load_cr3() since
it was assumed to be more logical.
Turns out this is incorrect: In efi_call_phys_prolog(), the gdt with its
physical address is loaded first, and when the %cr3 is reloaded in _epilog
from initial_page_table to swapper_pg_dir again the gdt is no longer
mapped. This results in a triple fault if an interrupt occurs after
load_cr3() and before load_fixmap_gdt(0). Calling load_fixmap_gdt(0) first
restores the execution order prior to commit eeb89e2bb1 and fixes the
problem.
Fixes: eeb89e2bb1 ("x86/efi: Load fixmap GDT in efi_call_phys_epilog()")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: linux-efi@vger.kernel.org
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Joerg Roedel <jroedel@suse.de>
Link: https://lkml.kernel.org/r/1536689892-21538-1-git-send-email-linux@roeck-us.net
The SYSCALL64 trampoline has a couple of nice properties:
- The usual sequence of SWAPGS followed by two GS-relative accesses to
set up RSP is somewhat slow because the GS-relative accesses need
to wait for SWAPGS to finish. The trampoline approach allows
RIP-relative accesses to set up RSP, which avoids the stall.
- The trampoline avoids any percpu access before CR3 is set up,
which means that no percpu memory needs to be mapped in the user
page tables. This prevents using Meltdown to read any percpu memory
outside the cpu_entry_area and prevents using timing leaks
to directly locate the percpu areas.
The downsides of using a trampoline may outweigh the upsides, however.
It adds an extra non-contiguous I$ cache line to system calls, and it
forces an indirect jump to transfer control back to the normal kernel
text after CR3 is set up. The latter is because x86 lacks a 64-bit
direct jump instruction that could jump from the trampoline to the entry
text. With retpolines enabled, the indirect jump is extremely slow.
Change the code to map the percpu TSS into the user page tables to allow
the non-trampoline SYSCALL64 path to work under PTI. This does not add a
new direct information leak, since the TSS is readable by Meltdown from the
cpu_entry_area alias regardless. It does allow a timing attack to locate
the percpu area, but KASLR is more or less a lost cause against local
attack on CPUs vulnerable to Meltdown regardless. As far as I'm concerned,
on current hardware, KASLR is only useful to mitigate remote attacks that
try to attack the kernel without first gaining RCE against a vulnerable
user process.
On Skylake, with CONFIG_RETPOLINE=y and KPTI on, this reduces syscall
overhead from ~237ns to ~228ns.
There is a possible alternative approach: Move the trampoline within 2G of
the entry text and make a separate copy for each CPU. This would allow a
direct jump to rejoin the normal entry path. There are pro's and con's for
this approach:
+ It avoids a pipeline stall
- It executes from an extra page and read from another extra page during
the syscall. The latter is because it needs to use a relative
addressing mode to find sp1 -- it's the same *cacheline*, but accessed
using an alias, so it's an extra TLB entry.
- Slightly more memory. This would be one page per CPU for a simple
implementation and 64-ish bytes per CPU or one page per node for a more
complex implementation.
- More code complexity.
The current approach is chosen for simplicity and because the alternative
does not provide a significant benefit, which makes it worth.
[ tglx: Added the alternative discussion to the changelog ]
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/r/8c7c6e483612c3e4e10ca89495dc160b1aa66878.1536015544.git.luto@kernel.org
Pull RISC-V fix from Palmer Dabbelt:
"This contains what I hope to be the last RISC-V patch for 4.19.
It fixes a bug in our initramfs support by removing some broken and
obselete code"
* tag 'riscv-for-linus-4.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/palmer/riscv-linux:
riscv: Do not overwrite initrd_start and initrd_end
As we have already binding for the H6 system controller, add its node
to the device tree.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[fixed compatible string]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
We currently do not notify all gmaps when using gmap_pmdp_xchg(), due
to locking constraints. This makes ucontrol VMs, which is the only VM
type that creates multiple gmaps, incompatible with huge pages. Also
we would need to hold the guest_table_lock of all gmaps that have this
vmaddr maped to synchronize access to the pmd.
ucontrol VMs are rather exotic and creating a new locking concept is
no easy task. Hence we return EINVAL when trying to active
KVM_CAP_S390_HPAGE_1M and report it as being not available when
checking for it.
Fixes: a4499382 ("KVM: s390: Add huge page enablement control")
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Message-Id: <20180801112508.138159-1-frankja@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
